检索结果-内蒙古大学图书馆

Influence of silicon infiltration on the wear and oxidation resistance of hot-pressed B4c/c(graphite) composites

cERAMIcS INTERNATIONAL 2021年第24期47卷 34927-34939页

作者： Jiang, Tao Han, Manman Fu, Jia Xian Shiyou Univ Sch Mat Sci & Engn Xian 710065 Shaanxi Peoples R China

B4c/c(graphite) composites were produced using Hot-pressing. However, the composites exhibited low surface hardness, low wear resistance as well as low oxidation resistance. The hot-pressed B4c/c(graphite) composites were processed via silicon infiltration procedure at 1550 degrees c for 2 h in the vacuum condition to refine the wear resistance, surface hardness, and oxidation resistance of the B4c/c(graphite) composites. The silicon infiltration process resulted in the fabrication of a surface layer based on silicon carbide and silicon upon the B4c/c (graphite) composites surface. The surface layer of the silicon infiltrated B4c/c(graphite) composites, primarily comprising silicon carbide and silicon, was examined for its phase composition and microstructure. The oxidation resistance, wear resistance, and surface hardness of B4c/c(graphite) composites subjected to silicon infiltration was additionally examined. The XRD results confirmed that silicon carbide and silicon-based layer existed on the surface of B4c/c(graphite) composites, which was produced as a result of the silicon infiltration process. The surface of silicon infiltrated B4c/c(graphite) composites exhibited a 300-400 mu m thick covering of silicon carbide and silicon. The deposited layer also exhibited a dense and compact microstructure. When compared to hot-pressed B4c/c(graphite) composites, the surface hardness and wear resistance of the composites resulting after silicon infiltration were significantly enhanced. Silicon infiltrated B4c/c(graphite) composites possess a surface hardness of 16-17 GPa. The oxidation resistance of the silicon infiltrated B4c/c(graphite) composites was considerably enhanced as compared to the hot-pressed B4c/c(graphite) composites. So the silicon infiltrated B4c/c(graphite) composites exhibited high surface hardness, excellent wear resistance and excellent oxidation resistance in comparison with the hot-pressed B4c/c(graphite) composites.

关键词： A Hot pressing B composites c Hardness Wear resistance

来源：评论

学校读者我要写书评

暂无评论

Effects of c/N ratio on anaerobic co-digestion of cabbage, cauliflower, and restaurant food waste

引用

BIOMASS cONVERSION AND BIOREFINERY 2021年第5期11卷 2133-2145页

作者： Beniche, I. Hungria, J. El Bari, H. Siles, J. A. chica, A. F. Martin, M. A. Univ Ibn Tofail Kenitra Morocco Lab Renewable Energy & Environm Energy Biomass & Biogas Team Fac Sci BP 133 Kenitra 14000 Morocco Univ Cordoba Dept Chem Engn Campus Univ RabanalesCtra N-4Km 396 Cordoba 14071 Spain

Every day, a large amount of food waste (FW) is generated that causes serious environmental problems such as the production of greenhouse gases and leachate. A possible treatment for this waste is anaerobic digestion (AD), but there are several problems associated with the accumulation of volatile fatty acids (VFA), foaming, or low buffer capacity. In order to resolve or mitigate this problem, FW was mixed with cabbage and cauliflower (ccF) leaves and stalks at different carbon/nitrogen ratios (c/N) to add value to this agricultural waste and benefit from the advantages of co-digestion. Under the study conditions, promising results were obtained during the co-digestion of FW and agricultural wastes at c/N = 45. These include a high biodegradability (98%), a methane yield of 475 mL(STP) cH4/g VS, and an organic loading rate (OLR) of 0.06 kg of VS/m(3) h for the ccF and FW mixture (ccF + FW). Anaerobic co-digestion of ccF + FW might be an interesting option for the simultaneous treatment of these types of organic waste, with the consequent social and environmental benefits.

关键词： Food waste cabbage cauliflower Anaerobic co-digestion c N ratio

来源：评论

学校读者我要写书评

暂无评论

Na3V2(PO4)3/c composites as low-cost and high-performance cathode materials for sodium-ion batteries

引用

INTERNATIONAL JOURNAL OF ENERGY RESEARcH 2021年第3期45卷 4534-4542页

作者： Zhu, Limin Ding, Guochun Sun, Qiancheng Xie, Lingling cao, Xiaoyu Henan Univ Technol Sch Chem & Chem Engn Zhengzhou Peoples R China Henan Univ Technol Key Lab High Specif Energy Mat Electrochem Power Zhengzhou 450000 Peoples R China Henan Univ Technol Sch Environm Engn Zhengzhou Peoples R China

The carbon layer acting as a conductive medium is beneficial to overcoming the comparatively inferior electronic conductivity of Na3V2(PO4)(3). Based on this, Na3V2(PO4)(3)/c composites with diverse ratios of citric acid are synthetized via rheological phase reaction way in this work. The consequences display that the Na3V2(PO4)(3)/c-1.5 composite brings a higher initial discharge capacity of 113.2 mAh g(-1) at a current rate of 1 c with coulombic efficiency above 99% during all cycles. The discharge capacity retains at 117.6 mAh g(-1) at the 100th cycle. Even at the high current densities of 5 c and 10 c, the composite also shows superior cycling performance with negligible capacity fading. Its discharge capacities decline from 97 to 92.6 mAh g(-1) at 5 c and from 85.3 to 83.7 mAh g(-1) at 10 c. These remarkable outcomes arise from its preferable morphology with suitable carbon coating because both excess and skimpy carbon seriously affect the microstructure and electrochemical properties of Na3V2(PO4)(3)/c composites.

关键词： carbon coating cathode materials Na3V2(PO4)(3) c rheological phase reaction sodium‐ ion batteries

来源：评论

学校读者我要写书评

暂无评论

Urchin-like MnO/c microspheres as high-performance lithium-ion battery anode

引用

IONIcS 2021年第4期27卷 1423-1428页

作者： Zhang, Lei Shen, Lian Liu, Yangai Suo, Guoquan China Univ Geosci Sch Mat Sci & Technol Natl Lab Mineral Mat Beijing Key Lab Mat Utilizat Nonmetall Minerals & Beijing 100083 Peoples R China Shaanxi Univ Sci & Technol Sch Mat Sci & Engn Xian 710021 Peoples R China

Manganese oxide (MnO) is prospective as anode material for lithium-ion batteries (LIBs) due to its low insertion voltage and high reversible capacity. Here, urchin-like MnO microspheres with carbon coating (u-MnO/c) are synthesized through hydrothermal method, and its lithium storage performance is investigated. The unique urchin-like structures of u-MnO/c endow it high surface area which provides sufficient contact with electrolyte. The carbon coating can effectively suffer volume change of u-MnO during charge/discharge process. Meanwhile, the carbon coating can effectively improve the conductivity of u-MnO-based anode. Due to the above features, u-MnO/c delivers high initial capacity of 845 mAh g(-1), and an obvious activation process is observed at the beginning of the cycles thanks to the abundant invasion of the electrolyte into u-MnO/c. The large capacity of 723 mAh g(-1) can still be achieved after 80 cycles. This work provides a promising guide for designing high-performance LIBs electrode materials.

关键词： Lithium ion batteries MnO c composite Microsphere

来源：评论

学校读者我要写书评

暂无评论

Acid Hydrolysis to Provide the Potential for Rice-Husk-Derived c/SiO₂ composites for Lithium-Ion Batteries

引用

JOURNAL OF ELEcTRONIc MATERIALS 2021年第8期50卷 4426-4432页

作者： Ma, Lijie Liu, Li Liu, Xiaoyang Li, Yixin Feng, Yi Tian, Yumei chao, Yimin Zhu, Yanchao Wang, Xiaofeng Jilin Univ Coll Chem State Key Lab Inorgan Synth & Preparat Chem 2699 Qianjin St Changchun 130012 Peoples R China Northeast Normal Univ Dept Chem Changchun 130024 Peoples R China Univ East Anglia Sch Chem Norwich Res Pk Norwich NR4 7TJ Norfolk England

As major waste materials in the rice milling industry, rice husks (RHs) have potential industrial applications. In this work, acid solutions were used to extract high-value-added polysaccharide components (hemicellulose and cellulose) from RHs to obtain sugar residues (SRs) for comprehensive utilization. The SRs were converted into c/SiO2 composites after carbonization and ball-milling. The c/SiO2 composites with crystalline cellulose content in the precursor possessed desirable electrochemical properties when tested as an anode material for lithium-ion batteries (LIBs), including cycle performance, initial coulombic efficiency (IcE) and electrical impedance. Meanwhile, a high reversible specific capacity of 553 mAh g(-1) was maintained after 100 cycles at a current density of 0.1 A g(-1). This method can be used to turn biomass into a potentially valuable anode material with desirable electrochemical properties for LIBs.

关键词： Rice husks sugar residues c SiO2 composites lithium-ion battery

来源：评论

学校读者我要写书评

暂无评论

ORR properties of S-modified co₃O₄@S-g-c₃N₄/c catalyst in alkaline electrolyte

引用

IONIcS 2021年第6期27卷 2545-2551页

作者： Dong, Xuewei Wang, Dongchao Qiu, Zhongyu Xuan, Jiaping Huang, Naibao Dalian Jiaotong Univ Sch Environm & Chem Engn Dalian Peoples R China Dalian Maritime Univ Dept Mat Sci & Engn Dalian Peoples R China

Developing high-efficiency and low-cost electrocatalysts for oxygen reduction reaction (ORR) is one of the key objectives for fuel cells. In this work, S-modified co3O4@S-g-c3N4/c catalyst was prepared by combining pyrolysis with ultrasonic method. Transmission electron microscopy analysis indicated that the obtained catalyst had a core-shell structure, which used co3O4 as its core and 1.5-nm-thick S-interspersed g-c3N4 encapsulated co3O4 as shell. When the ratio of S to g-c3N4 was 1:3, the as-prepared catalyst co3O4@ S-g-c3N4/c exhibited positive onset potential and higher limiting diffusion current density of 4.00 mA cm(-2) @0.8V, which was 10 and 37% higher than that of co3O4@g-c3N4/c and co3O4/c, respectively. After 2000 cV cycles, the catalyst also showed good durability.

关键词： Fuel cell co3O4 ORR catalyst co3O4@ S-g-c3N4 c

来源：评论

学校读者我要写书评

暂无评论

Wavelet analysis of a flexible filament kinematics: emulating c. elegans swimming behavior

引用

JOURNAL OF THE BRAZILIAN SOcIETY OF MEcHANIcAL ScIENcES AND ENGINEERING 2021年第4期43卷 1-13页

作者： Malvar, Sara carmo, Bruno S. Univ Sao Paulo Dept Mech Engn Escola Politecn Av Prof Mello Moraes 2231 Sao Paulo Brazil

This paper discusses different aspects of an active flexible filament propulsion in a liquid medium. The immersed boundary method is used to model a flexible filament immersed in Newtonian fluid at low Reynolds numbers. The flexible filament motion emulates that of a c. elegans. We varied some parameters of the filament motion, such as the interpolation points of the function related to the curvature of the filament and the upstroke and downstroke period, and analyzed the kinematic response in the body displacement and fluid flow. A methodology based on signal analysis is proposed for correct modeling of the movement of these filaments. The swimming velocity and distance are analyzed using wavelet transform, in which the notion of time-frequency localization is made precise. This methodology allows defining which parameters lead to the best efficiency, e.g., greater swim distance for the same number of strokes, making it very valuable for passive control of the filament.

关键词： Wavelet analysis c elegans Immersed boundary method Active matter

来源：评论

学校读者我要写书评

暂无评论

Microstructure and oxidation mechanism of multiphase Mo-Ti-Si-B alloys at 800 °c

引用

cORROSION ScIENcE 2021年 187卷 109518-109518页

作者： Zhao, Mi Xu, Boyang Shao, Yuman Zhu, Yan Wu, Jie Wu, Shusen Yan, Youwei Huazhong Univ Sci & Technol Sch Aerosp Engn 1037 Luoyu Rd Wuhan 430074 Peoples R China Huazhong Univ Sci & Technol Sch Mat Sci & Engn State Key Lab Mat Proc & Die & Mould Technol 1037 Luoyu Rd Wuhan 430074 Peoples R China Huazhong Univ Sci & Technol Sch Mech Sci & Engn 1037 Luoyu Rd Wuhan 430074 Peoples R China

Three Mo-Ti-Si-B alloys with compositions of 50Mo-20Ti-20Si-10B, 40Mo-30Ti-20Si-10B and 30Mo-40Ti-20Si-10B (at.%) were designed and prepared by arc-melting. Microstructure evolution at 1600 degrees c and oxidation mechanism at 800 degrees c of these alloys were analyzed. 50Mo-20Ti-20Si-10B suffered from pesting because of a large volume fraction of Mo3Si, which produced porous products with severe volume expansion. Both 40Mo-30Ti-20Si-10B and 30Mo-40Ti-20Si-10B have better oxidation resistance. It can be inferred that during long-term oxidation, interactions between constituent phases contributed to the overall oxidation resistance of the alloys.

关键词： A Intermetallics B SEM Weight loss c High temperature corrosion Oxidation

来源：评论

学校读者我要写书评

暂无评论

Nitrogen removal performance and bacterial communities in zeolite trickling filter under different influent c/N ratios

引用

ENVIRONMENTAL ScIENcE AND POLLUTION RESEARcH 2021年第13期28卷 15909-15922页

作者： Liu, Lina Li, Na Tao, chunyang Zhao, Yubo Gao, Jingqing Huang, Zhenzhen Zhang, Jingshen Gao, Jianlei Zhang, Jinliang cai, Ming Zhengzhou Univ Sch Ecol & Environm Zhengzhou Henan Peoples R China Zhengzhou Yuanzhihe Environm Protect Technol Co L Zhengzhou Henan Peoples R China Zhengzhou Univ Sch Water Conservancy & Engn Zhengzhou 450001 Henan Peoples R China Yellow River Engn Consulting Co Ltd Zhengzhou 450003 Henan Peoples R China

In this study, the degradation performance of nutrients in zeolite trickling filter (ZTF) with different influent c/N ratios and aeration conditions was investigated. Microaeration was beneficial for enhancing NH4+-N removal performance. Due to the sufficient carbon source supply under a c/N ratio of 8, a high removal efficiency of NH4+-N and TN was simultaneously observed in ZTF. In addition, TN removal mainly occurred at the bottom, which might be explained by the sufficient nutrients available for bacteria to multiply in this zone. The abundant genera were Acinetobacter, Gemmobacter, Flavobacterium, and Pseudomonas, all of which are heterotrophic nitrification-aerobic denitrification (HNAD) bacteria. In addition, biofilm only slowed down the adsorption rate but did not significantly reduce the adsorption capacity of zeolite. Bio-zeolite had NH4+-N well adsorption capacity and bio-desorption capacity. Biological nitrogen removal performance was superior to physicochemical absorption of zeolite. The results suggested that the physicochemical of zeolite and biochemical reactions of microorganism coupling actions may be the main nitrogen transformation pathway in ZTF. Our research provides a reference for further understanding the nitrogen removal mechanism of zeolite bioreactors.

关键词： Zeolite trickling filter c N ratios Microaeration Nitrogen removal Heterotrophic nitrification-aerobic denitrification Physicochemical absorption

来源：评论

学校读者我要写书评

暂无评论

Single-Pore versus Dual-Pore Bipyridine-Based covalent-Organic Frameworks: An Insight into the Heterogeneous catalytic Activity for Selective c-H Functionalization

引用

SMALL 2021年第22期17卷 2003970-2003970页

作者： Vardhan, Harsh Al-Enizi, Abdullah M. Nafady, Ayman Pan, Yanxiong Yang, Zhongyu Gutierrez, Humberto R. Han, Xiaolong Ma, Shengqian Univ S Florida Dept Chem 4202 E Fowler Ave Tampa FL 33620 USA King Saud Univ Coll Sci Dept Chem Riyadh 11451 Saudi Arabia North Dakota State Univ Dept Chem & Biochem 1231 Albrecht Blvd Fargo ND 58108 USA Univ S Florida Dept Phys Tampa FL 33620 USA Northwest Univ Sch Chem Engn Xian 710069 Shaanxi Peoples R China Univ North Texas Dept Chem 1508 W Mulberry St Denton TX 76201 USA

Exponential growth in the field of covalent-organic frameworks (cOFs) is emanating from the direct correlation between designing principles and desired properties. The comparison of catalytic activity between single-pore and dual-pore cOFs is of importance to establish structure-function relationship. Herein, the synthesis of imine-linked dual-pore [(BPyDc)](x)(%)-ETTA cOFs (x = 0%, 25%, 50%, 75%, 100%) with controllable bipyridine content is fulfilled by three-component condensation of 4,4 ',4 '',4 '''-(ethene-1,1,2,2-tetrayl)tetraaniline (ETTA), 4,4 '-biphenyldialdehyde, and 2,2 '-bipyridyl-5,5 '-dialdehyde in different stoichiometric ratio. The strong coordination of bipyridine moieties of [(BPyDc)](x)(%)-ETTA cOFs with palladium imparts efficient catalytic active sites for selective functionalization of sp(2)c-H bond to c-X (X = Br, cl) or c-O bonds in good yield. To broaden the scope of regioselective c-H functionalization, a wide range of electronically and sterically substituted substrates under optimized catalytic condition are investigated. A comparison of the catalytic activity of palladium decorated dual-pore frameworks with single-pore imine-linked Pd(II) @ Py-2,2 '-BPyDc framework is undertaken. The finding of this work provides a sporadic example of chelation-assisted c-H functionalization and disclosed an in-depth comparison of the relationship between superior catalytic activity and core properties of rationally designed imine linked frameworks.

关键词： c -H functionalization covalent-organic frameworks heterogeneous catalysis palladium pore surface engineering

来源：评论

学校读者我要写书评

暂无评论

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

请选择保存的检索档案：

请选择收藏分类：

通借通还

建议与咨询 留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

请选择保存的检索档案： 新增检索档案 确定 取消

请选择收藏分类： 新增自定义分类 确定 取消

通借通还

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

请选择保存的检索档案：

请选择收藏分类：