检索结果-内蒙古大学图书馆

Solution chemistry back‐contact FTO/hematite interface engineering for efficient photocatalytic water oxidation

Chinese Journal of Catalysis 2022年第5期43卷 1247-1257页

作者： Karen Cristina Bedin Beatriz Mouriño Ingrid Rodríguez-Gutiérrez João Batista Souza Junior Gabriel Trindade dos Santos Jefferson Bettini Carlos Alberto Rodrigues Costa Lionel Vayssieres Flavio Leandro Souza The National Nanotechnology Laboratory(LNNANO) Brazilian Center for Research in Energy and Materials(CNPEM)Campinas 13083‐970Brazil Centro de Ciências Naturais e Humanas(CCNH) Federal University of ABC(UFABC)Santo André09210580Brazil Federal University of Rio Grande do Sul(UFRGS) Rio Grande do SulBrazil International Research Center for Renewable Energy(IRCRE) State Key Laboratory of Multiphase Flow in Power EngineeringSchool of Energy and Power EngineeringXi’an Jiaotong UniversityXi’an 710049ShaanxiChina

This work describes a simple yet powerful scalable solution chemistry strategy to create back‐contact rich interfaces between substrates such as commercial transparent conducting fluorine‐doped tin oxide coated glass(FTO)and photoactive thin films such as hematite for low‐cost water oxidation ***‐resolution electron microscopy(SEM,TEM,STEM),atomic force microscopy(AFM),elemental chemical mapping(EELS,EDS)and photoelectrochemical(PEC)investigations reveal that the mechanical stress,lattice mismatch,electron energy barrier,and voids between FTO and hematite at the back‐contact interface as well as short‐circuit and detrimental reaction between FTO and the electrolyte can be alleviated by {1. the chemical composition of the precursor solutions,thus increasing the overall efficiency of these low‐cost photoanodes for water oxidation reaction for a clean and sustainable generation of hydrogen from PEC water‐*** findings are of significant importance to improve the charge collection efficiency by minimizing electron‐hole recombination observed at back‐contact interfaces and grain boundaries in mesoporous electrodes,thus improving the overall efficiency and scalability of low‐cost PEC water splitting devices.

关键词： Nanostructure Iron oxide Water oxidation Photoanode Surface engineering Chemical synthesis

来源：评论

学校读者我要写书评

暂无评论

Research on a Poly-Generation System for Gas-Biochar-Heat-Electricity by Supercritical Water Gasification of Biomass Waste

SSRN

引用

SSRN 2024年

作者： Wang, Cui Jin, Hui School of Water and Environment Chang'an University Xi’an710054 China Key Laboratory of Subsurface Hydrology and Ecological Effect in Arid Region of the Ministry of Education Chang'an University Xi’an710054 China Key Laboratory of Eco-hydrology and Water Security in Arid and Semi-arid Regions of Ministry of Water Resources Chang’an University Xi’an710054 China State Key Laboratory of Multiphase Flow in Power Engineering Xi'an Jiaotong University Xi’an710049 China Ministry of Education of China Chongqing University Chongqing400044 China

Biomass energy is renewable and rich in the world, providing a solution for the shortage in fossil fuel and serious environmental pollution. Proposing efficient utilization method of biomass waste demands urgent attention. Supercritical water gasification (SCWG) process is a potential technology. In this work, a poly-generation system based on SCWG was developed to convert biomass waste to gas, biochar, heat and electricity. Firstly, mass, energy, and exergy flow were calculated at the typical condition. Subsequently, impact of various operating parameters, including gasification temperature, mass flowrate of preheated water, biomass concentration, on the hydrogen-rich syngas yield, generated electricity, thermodynamic performance of the system was investigated. The result demonstrated that the exergy loss primarily occurred on cooler, reactor, heat exchanger and preheater, accounting for more than 90% of total exergy loss under different conditions, arising from irreversible reaction, heat transfer and heat dissipation. Higher temperature, higher biomass concentration and more preheated water exerted a positive effect for hydrogen-rich gas production and supplied heat energy, while these parameters were disadvantageous to exergy efficiency. Biochar energy was primarily affected by biomass concentration. Energy efficiency increased with preheated water quantity and biomass concentration rising, and impact of biomass concentration was more significant. Conversely, evaluated gasification temperature displayed an adverse effect on energy efficiency. The maximal exergy efficiency reached about 58.3% at 550℃, biomass concentration of 33%, preheated water mass flowrate of 900 kg·h-1.© 2024, The Authors. All rights reserved.

关键词： Biomass

来源：评论

学校读者我要写书评

暂无评论

Numerical study on the influence of plugging rate on the performance of adjustable steam ejector

International Journal of Fluid Engineering

引用

International Journal of Fluid engineering 2024年第2期1卷 50-60页

作者： Jianxiang Gao Zepeng Yuan Yuyan Hou Weixiong Chen State Key Laboratory of Multiphase Flow in Power Engineering Xi’an Jiaotong UniversityXi’an 710049People’s Republic of China

During the operation of thermal power plant systems, severe challenges to the quality and safety of the heat supply arise owing to the effects of peak regulation. Steam ejectors, widely employed in the district heating sector, often exhibit poorer performance under off-design conditions as a result of their fixed structure. This study analyzes the effects of varying plugging rate, primary pressure, and induced pressure on the performance of adjustable steam ejectors. As the plugging rate increases, the mass {1. rate of the primary fluid decrease, potentially falling below 32%, and that of the induced fluid initially experiences a minor increase, followed by a rapid decrease. Concurrently, the critical back pressure also decreases with an increase in the plugging rate, potentially falling by up to 65%. By contrast, the entrainment ratio surges with increasing plugging rate, with the maximum increase reaching up to 4.75 times. Under the same primary steam pressure and induced steam pressure, there exists an optimal entrainment ratio. Furthermore, both the critical back pressure and the optimal entrainment ratio increase as the primary steam pressure and induced steam pressure increase.

关键词： performance steam optimal

来源：评论

学校读者我要写书评

暂无评论

Adsorption of Dibenzofuran by Modified Biochar Derived from Microwave Gasification

SSRN

引用

SSRN 2024年

作者： Ren, Jiyun Zhang, Yong Wang, Hui Huang, Xiaoming Jin, Xiaoling Zhang, Kai Li, Ruiyu Yang, Kaixuan Yue, Yang Deng, Lei Che, Defu State Key Laboratory of Multiphase Flow in Power Engineering School of Energy and Power Engineering Xi’an Jiaotong University Xi’an710049 China Yantai Longyuan Power Technology Co. Ltd Yantai264000 China West Pipeline Company of PipeChina Urumchi830000 China Jinggangshan Power Plant Huaneng Power International Inc Jiangxi 343009 China Shunde Institute of Inspection Guangdong Institute of Special Equipment Inspection and Research Foshan528300 China Shanghai Power Equipment Research Institute Co. Ltd. Shanghai200240 China

Dioxins, emanating from the waste incineration, constitutes an organic pollutant that poses considerable risks to human health and environment. In this study, the corn straw char (CSC) and oak char (OC) derived from the electric heating and microwave gasification, and the coconut-shell activated carbon (AC) are employed as absorbents for the adsorption of dibenzofuran (DBF, dioxins model compound). Characterization techniques including BET, X-ray CT, SEM-EDS, FTIR, and XPS are performed to identify the DBF adsorption mechanism on biochar. The results show that the biochar prepared by the microwave gasification has a more well-developed pore structure than that of the electric heating gasification. Higher porosity (1..94%) and lower mineral content (1.75%) are responsible for the effective adsorption of DBF onto AC. The adsorption capacity of CSC is proportional to the modified concentration of KOH. It is mainly ascribed to the decrement of carboxyl and lactone groups and the enhancement of alkaline functional groups on the biochar surface, which augments the hydrophobicity and π–π electron donor–acceptor (EDA) interaction. Instead, DBF adsorption capacity on the biochar is adversely affected by HNO3 modification. For all biochar samples, the corresponding maximum adsorption ratios are AC (87.1.%) > KOH-modified CSC (77.1.%) > unmodified CSC (49.1.%) > unmodified OC (39.70%) > HNO3-modified CSC (36.09%). The adsorption mechanisms of DBF on the gasified biochar encompass pore filling, hydrophobicity, and π–π EDA interaction. A desirable adsorption capacity of DBF on the biochar prepared by the microwave gasification is attainable through augmenting the specific surface area while diminishing the oxygen-containing groups of the surface simultaneously. © 2024, The Authors. All rights reserved.

关键词： Potassium hydroxide

来源：评论

学校读者我要写书评

暂无评论

Investigation of Droplet Dynamic Behavior in Pemfcs Gas Diffusion Layer and Gas Channel with Micro-Ct and Lattice Boltzmann Method

SSRN

引用

SSRN 2024年

作者： Lv, Xuecheng Zhou, Zhifu Wu, Wei-Tao Wei, Lei Gao, Linsong Lyu, Jizu Hu, Chengzhi Li, Yang Li, Yubai Song, Yongchen Key Laboratory of Ocean Energy Utilization and Energy Conservation of Ministry of Education Dalian University of Technology Dalian116024 China State Key Laboratory of Multiphase Flow in Power Engineering Xi'an Jiaotong University Xi'An710049 China School of Mechanical Engineering Nanjing University of Science and Technology Nanjing210094 China Department of Mechanical and Energy Engineering Southern University of Science and Technology Shenzhen518055 China School of Mechanical Engineering and Mechanics Xiangtan University Xiangtan411105 China School of Mechanical Engineering Guangdong Ocean University Zhanjiang524088 China

This study reconstructed the 3D structure for the gas diffusion layer (GDL) of proton exchange membrane fuel cells (PEMFCs) using the micro-CT technique and investigated the dynamic behavior of droplets inside the multi-scale space of GDL and gas channel (GC) using the lattice Boltzmann method (LBM). The prediction model for droplet detachment at the GDL-GC interface was developed. The results indicate that there is a significant difference between the breakage location of the liquid bridge and the trajectory of the liquid droplet after detaching from the GDL-GC interface in the multi-scale space of GC and GDL, compared to the single-scale GC space where GDL is ignored. The increase in gas velocity and internal contact angle of the GDL contribute to reducing the droplet detachment volume and increasing the droplet detachment frequency. At the internal contact angle of 1.0º-1.0º, GDL exhibited the most efficient removal of liquid water. A contact angle smaller than this range would hinder the detachment of droplets in the GC, while a contact angle larger than this range would lead to the accumulation of liquid water in the GDL. The surface force generated by the connection of liquid bridges in the analytical model for critical droplet detachment forms an angle with the gas flow direction, with the characteristic length determining this force being the minimum diameter at the necking of the liquid bridge. © 2024, The Authors. All rights reserved.

关键词： Contact angle

来源：评论

学校读者我要写书评

暂无评论

Research on a Poly-Generation System for Gas-Biochar-Heat-Electricity by Supercritical Water Gasification of Biomass Waste

SSRN

引用

SSRN 2024年

Biomass energy is renewable and rich in the world, providing a solution for the shortage in fossil fuel and serious environmental pollution. Proposing efficient utilization method of biomass waste demands urgent attention. Supercritical water gasification (SCWG) process is a potential technology. In this work, a poly-generation system based on SCWG was developed to convert biomass waste to gas, biochar, heat and electricity. Firstly, mass, energy, and exergy flow were calculated at the typical condition. Subsequently, impact of various operating parameters on the hydrogen-rich syngas yield, generated electricity, thermodynamic performance was investigated. The result demonstrated that the exergy loss primarily occurred on cooler, reactor, heat exchanger and preheater, accounting for more than 90% of total exergy loss, arising from irreversible reaction, heat transfer and heat dissipation. Higher temperature, biomass concentration and preheated water exerted a positive effect for hydrogen-rich gas production and supplied heat energy, while these parameters were disadvantageous to exergy efficiency. Biochar energy was affected by biomass concentration. Energy efficiency increased with preheated water quantity and biomass concentration rising, and impact of biomass concentration was more significant. Conversely, evaluated gasification temperature displayed an adverse effect on energy efficiency. The maximal exergy efficiency reached 58.3% at 550℃, 33%, 900 kg·h-1. © 2024, The Authors. All rights reserved.

关键词： Biomass

来源：评论

学校读者我要写书评

暂无评论

Research on a Poly-Generation System for Gas-Biochar-Heat-Electricity by Supercritical Water Gasification of Biomass Waste

SSRN

引用

SSRN 2024年

Biomass energy is renewable and rich in the world, providing a solution for the shortage in fossil fuel and serious environmental pollution. Proposing efficient utilization method of biomass waste demands urgent attention. Supercritical water gasification (SCWG) process is a potential technology. In this work, a poly-generation system based on SCWG was developed to convert biomass waste to gas, biochar, heat and electricity. Firstly, mass, energy, and exergy flow were calculated at the typical condition. Subsequently, impact of various operating parameters, including gasification temperature, mass flowrate of preheated water, biomass concentration, on the hydrogen-rich syngas yield, generated electricity, thermodynamic performance of the system was investigated. The result demonstrated that the exergy loss primarily occurred on cooler, reactor, heat exchanger and preheater, accounting for more than 90% of total exergy loss under different conditions, arising from irreversible reaction, heat transfer and heat dissipation. Higher temperature, higher biomass concentration and more preheated water exerted a positive effect for hydrogen-rich gas production and supplied heat energy, while these parameters were disadvantageous to exergy efficiency. Biochar energy was primarily affected by biomass concentration. Energy efficiency increased with preheated water quantity and biomass concentration rising, and impact of biomass concentration was more significant. Conversely, evaluated gasification temperature displayed an adverse effect on energy efficiency. The maximal exergy efficiency reached about 58.3% at 550°C, biomass concentration of 33%, preheated water mass flowrate of 900 kg·h-1.© 2024, The Authors. All rights reserved.

关键词： Biomass

来源：评论

学校读者我要写书评

暂无评论

A Thermal Calculation Model for Tubular Condensing Heat Exchanger

SSRN

引用

SSRN 2023年

作者： Han, Lei Yang, Kaixuan Yang, Jiahui Li, Ruiyu Li, Yuhang Deng, Lei Che, Defu State Key Laboratory of Multiphase Flow in Power Engineering School of Energy and Power Engineering Xi’an Jiaotong University Xi’an710049 China Shanghai Power Equipment Research Institute Co. Ltd. Shanghai200240 China Shunde Institute of Inspection Guangdong Institute of Special Equipment Inspection and Research Foshan528300 China Xi’an Thermal Power Research Institute Co. Ltd. Xi’an710032 China

The condensing heat exchanger is commonly applied in various heat exchange systems. It can efficiently recover moisture and heat from the flue gas that contains water vapor. However, the convective-condensation heat transfer process is so complicated that no mature thermal calculation model is available. This study develops a thermal calculation model for the widely employed tubular condensing heat exchanger in industry. To characterize the degree of the heat and mass transfer, this study introduces two parameters, namely the sensible and latent heat transfer efficiencies of fin. The thermal calculations are conducted for the condensing heat exchangers reported in the literature to verify the proposed model by comparing it with the experimental data. The results show that the absolute error of the calculated sensible and latent heat transfer efficiencies is 0.0365 and 0.0268, respectively. A maximum difference of 5.2 K has been acquired between the measured and calculated values of the outlet temperature. The relative error of the condensate water flowrate is mostly within ±5.0% and ±1..0% under the bare-tube and finned-tube conditions, respectively, with a maximum deviation of 0.7 and 1.4 kg h-1. This study provides a general model for designing and optimizing various tubular condensing heat exchangers accurately. © 2023, The Authors. All rights reserved.

关键词： Mass transfer

来源：评论

学校读者我要写书评

暂无评论

Thermodynamic analysis on a heat-power decoupling system integrated with absorption heat pump

Thermodynamic analysis on a heat-power decoupling system int...

引用

201. Canadian Society for Civil engineering Annual Conference, CSCE 201.

作者： Wang, Liyuan Liu, Ming Fu, Yue Liu, Jiping Yan, Junjie MOE Key Laboratory of Thermal Fluid Science Engineering School of Energy and Power Engineering Xi'an Jiaotong University Xi'an Shaanxi China State Key Laboratory of Multiphase Flow in Power Engineering School of Energy and Power Engineering Xi'an Jiaotong University Xi'an Shaanxi China

ISBN: (纸本)9780791883747

Because of the continuous expanding of the district heating, the heating load of combined heat and power(CHP) plants increases year by year. The minimum power load of CHP plant increases with the heating load due to the heat-power coupling mechanism. Therefore, heat-power decoupling is necessary to improve the operation flexibility for CHP units. Integrating the absorption heat pump(AHP) is an effective method to realize the heat-power decoupling. In this study, a 330MW CHP unit model and AHP model have been developed and validated. The performance of the heat-power decoupling and energy saving performance has been investigated by comparing the thermodynamic performance indicators. Results show that, the proposed system can increase the maximum heating load and decrease the power generation when the primary network return temperature is decreased. When the heating steam extraction is kept constant, with the increase of the primary network return water temperature, the heat generation efficiency and the standard coal consumption rate of heating increases, the coal consumption rate of power generation and the heating efficiency decreases. And the primary network return water temperature increases from 40 °C to 70 °C, the coal consumption rate of power generation decreases by 4.3 g/kWh, and the coal consumption rate of heating increases by 0.67 kg/GJ. Copyright © 2020 ASME.

关键词： Water temperature

来源：评论

学校读者我要写书评

暂无评论

Theoretical study on flow and radiation in tubular solar photocatalytic reactor

引用

Frontiers in Energy 2021年第3期15卷 687-699页

作者： Qingyu WEI Yao WANG Bin DAI Yan YANG Haijun LIU Huaijie YUAN Dengwei JING Liang ZHAO International Research Center for Renewable Energy State Key Laboratory of Multiphase Flow in Powering EngineeringXi’an Jiaotong UniversityXi’an 710049China Beijing Aerospace Propulsion Institute Beijing 100076China School of Energy and Power Engineering University of Shanghai for Science and TechnologyShanghai 200093China

In this paper,based on the mixture flow model,an optimized six-flux model is first established and applied to the tubular solar photocatalytic *** influencing photocatalyst distribution and radiation distribution at the reactor outlet,*** concentration and circulation speed,are also *** is found that,at the outlet of the reactor,the optimized six-flux model has better performances(the energy increase by 1.00%and 284%,respectively)with a higher catalyst concentration(triple)and a lower speed(one third).

关键词： photocatalytic hydrogen photoreactor numerical simulation solar energy flow model radiation model

来源：评论

学校读者我要写书评

暂无评论

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

请选择保存的检索档案：

请选择收藏分类：

通借通还

建议与咨询 留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

请选择保存的检索档案： 新增检索档案 确定 取消

请选择收藏分类： 新增自定义分类 确定 取消

通借通还

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

请选择保存的检索档案：

请选择收藏分类：