The enhanced electrochemical stability of the synthesized hybrid catalyst has been demonstrated by the introduction of the synergistic effect between carbon powder additive and the prepared catalyst. Single crystal Ir...
详细信息
CdS/TiO2 composites consisted of uniform anatase TiO2 of 15 nm are successfully prepared by water in oil method with cubic phase CdS nanocrystals highly dispersed, which exhibits strong visible light absorption at abo...
详细信息
SiC/Cu composites exhibit low density, low coefficient of thermal expansion and excellent mechanical properties. In this study, Zn of 2 wt. % was added as the sintering activator, and the high volume faction (60%) SiC...
详细信息
A novel kind of porous SiO2@TiO2 microspheres have been synthesized by a convenient hydrothermal method with SiO2 spheres as the core strcuture, which exhibits an enhanced degradation rate towards gaseous benzene than...
详细信息
Antimony-doped tin oxide (ATO) nanoparticles with controlled doping level were prepared by a nonaqueous solution route, using alcohol as the solvent, citric acid as an agent, tin (IV) tetrachloride as tin source and a...
详细信息
Loosely packed MoS2 nanosheets with thin carbon coating were synthesized via a facile, one-pot hydrothermal growth method. In the resulted optimal-designed nanoarchitecture, the ultrathin nanosheets, with a wall-thick...
Loosely packed MoS2 nanosheets with thin carbon coating were synthesized via a facile, one-pot hydrothermal growth method. In the resulted optimal-designed nanoarchitecture, the ultrathin nanosheets, with a wall-thickness of approximately 5-10 nm, provide large electrode-electrolyte interface, so as to facilitate faster lithium-ions intercalation and diffusion. The flexible and conductive carbon overcoats accommodate and alleviate the volume variation of the composites and thus maintain the structural and electrical integrity. In favor of the synergy and interplay of the carbon effect and intrinsic structural advantages, MoS2@C (1:2) composites with the precursor MoO3: D-glucose molar ratio of 1:2 exhibit high reversible specific capacity of 1419 mA h g-1 at 0.1 A g-1, retain 80 % of the capacity after 50 cycles, and excellent rate capability as high as 672 mA h g-1 at 10 A g-1 with almost 100 % Coulombic efficiency. The good electrochemical performance suggests that these MoS2@C composites with unique flower-like morphology give rise to high specific surface area and increased layer distance leading to the reduced diffusion path of lithium-ions and rapid electrons transport. The rational and optimal design of the MoS2@C composites with an excellent electrochemical performance in the report creates a new avenue to develop a high-performance anode material.
Multi walled carbon nanotubes decorated with ferriferrous oxide nanoparticle (MWCNTs-Fe3O4) complex was used as an effective reinforcement in the polymer composites. The MWCNTs-Fe3O4 with various grafting contents of ...
Multi walled carbon nanotubes decorated with ferriferrous oxide nanoparticle (MWCNTs-Fe3O4) complex was used as an effective reinforcement in the polymer composites. The MWCNTs-Fe3O4 with various grafting contents of Fe3O4 nanoparticles were successfully prepared by combining in situ atom transfer radical polymerization (ATRP) and coprecipitation process, which was characterized with Fourier transform infrared spectroscopy (FT-IR) and transmission electron microscope (TEM). The MWCNTs-Fe3O4 complex showed the strong magnetic response behavior, which could be easily aligned in an external magnetic field. The alignment state of MWCNTs-Fe3O4 complex could be modulated by adjusting the intensity of external magnetic field, grafting content of Fe3O4 nanoparticles and viscosity of the solvent. Moreover, with the addition of MWCNTs-Fe3O4, tensile strength and modulus of epoxy composites were enhanced by 12.3 and 10.9%, respectively, which was due to the reinforcing effect of the aligned MWCNTs-Fe3O4 within magnetic field.
The microstructures and mechanical properties of 550 MPa grade lightweight high strength thin-walled H-beam steel were experimentally studied. The experimental results show that the microstructure of the air-cooled H-...
详细信息
The microstructures and mechanical properties of 550 MPa grade lightweight high strength thin-walled H-beam steel were experimentally studied. The experimental results show that the microstructure of the air-cooled H-beam steel sample is consisted of ferrite, pearlite and a small amount of granular bainites as well as fine and dispersive V（C,N） precipitates. The microstructure of the water-cooled steel sample is consisted of ferrite and bainite as well as a small amount of fine pearlites. The microstructure of the water-cooled sample is finer than that of the air-cooled sample with the average intercept size of the surface grains reaching to 3.5 gna. The finish rolling temperature of the thin-walled high strength H-beam steel is in the range of 750 ~C-850 ~C. The lower the finish rolling temperature and the faster the cooling rate, the finer the ferrite grains, the volume fraction of bainite is increased through water cooling process. Grain refinement strengthening and precipitation strengthening are used as major strengthening means to develop 550 MPa grade lightweight high strength thin- walled H-beam steel. Vanadium partially soluted in the matrix and contributes to the solution strengthening. The 550 MPa grade high-strength thin-walled H-beam steel could be developed by direct air cooling after hot rolling to fully meet the requirements of the target properties.
暂无评论