检索结果-内蒙古大学图书馆

STUDY ON IMPROVEMENT OF POWER GENERATION FOR A WINDOW BY SOLAR RADIATION REFLECTED FROM THE LOW-E COAT OF A SEMI TRANSPARENT PHOTOVOLTAIC MODULE THAT IS EQUALLY ARRANGED LINEAR DOUBLE-SIDED SOLAR CELLS

引用

Journal of Environmental Engineering (Japan) 2024年第821期89卷 399-409页

作者： Umeda, Kazuhiko Yamaguchi, Akira Taisei Advanced Center of Technology TAISEI CORPORATION Japan Design Division TAISEI CORPORATION Japan

A study was conducted on the improvement of power generation for a window by solar radiation reflected from Low-E coat of a semi transparent photovoltaic module. This module is composed of a double-glazing that be installed a low-E glass in the indoor side and a solar module equally arranged linear double-sided solar cells in the outdoor side. As a result of outdoor verification, it was confirmed that annual power generation by Low-E coat increased by about 9%. The simulation also shows that there is a power generation advantage against the model using the square cell. © 2024 Architectural Institute of Japan. All rights reserved.

关键词： Glass

来源：评论

学校读者我要写书评

暂无评论

SHAKING TABLE TEST OF THE HIGH-DAMPING STRUCTURAL SYSTEM WITH MULTI-STORY SHEAR WALLS AND DAMPERS

引用

AIJ Journal of technology and design 2023年第71期29卷 62-67页

作者： Tani, Tsubasa Ishikawa, Yoshiyuki Maseki, Ryota Nakajima, Tohru Taisei Advanced Center of Technology Japan Design Division Taisei Corporation Japan

Shaking table tests using vibration model are conducted to verify the vibration characteristics of high-damping structural system with multistory shear walls and dampers. The system can reduce response under earthquakes significantly compared to conventional vibration control system which dampers work in response to inter-story drift. Analysis simulating the tests is also conducted and it reveals that the key index representing response reduction effect of the system is damper deformation amplification ratio. © 2023 Architectural Institute of Japan. All rights reserved.

关键词： Vibration control

来源：评论

学校读者我要写书评

暂无评论

Phase-field simulation of precipitation kinetics and creep properties of Ni-Al-Cr/Ta superalloys

引用

Science China(Technological Sciences) 2024年第4期67卷 1139-1150页

作者： YANG ShuaiGe ZHANG Zan ZHUO JiCheng LONG HongLi LI YongSheng National Key Laboratory of Advanced Casting Technologies MIIT Key Laboratory of Advanced Metallic and Intermetallic Materials TechnologyEngineering Research Center of Materials Behavior and DesignMinistry of EducationNanjing University of Science and TechnologyNanjing 210094China

The precipitation kinetics ofγ'-Ni_(3)(Al,Ta)phase and creep properties of Ni-15Al-x Ta at.%superalloys are investigated by the crystal plasticity phase-field *** results show that the high Ta content brings a lower creep strain for the deceleration and steady creep stage,while the creep lifetime is *** large external strain intensifies the creep damage and shortens the creep life of Ni-15Al-3Ta at.%*** kinetics evolution and elements distribution are revealed in the quaternary Ni-10Al-8.5Cr-xT a(x=1.5 at.%,2.0 at.%,2.5 at.%)superalloys by the multi-component phase-field *** anti-phase boundary(APB)changes the coarsening mechanism ofγ'phase,and Ta promotes the precipitation ofγ'phase with an increasing volume fraction and particle *** composition difference betweenγ'andγphases increases with the rising of Ta content,the strong partitioning of Ta toγ'phase strengthens the partitioning of Ni and Cr toγmatrix,and Ta shows a superiority than Al in the lattice site occupation of L1_(2)-Ni_(3)(Al,X)*** an importantγ'phase forming element,the optimization of Ta content is essential for improving the mechanical properties of Ni-based superalloys.

关键词： Ni-Al-Ta alloys creep properties kinetics phase-field

来源：评论

学校读者我要写书评

暂无评论

Precipitating thermally reinforcement phase in aluminum alloys for enhanced strength at 400℃

引用

Journal of Materials Science & technology 2024年第5期172卷 71-82页

作者： Xiang Su Yuan Lei Yang Chen Hongjie Qu Zhixiang Qi Gong Zheng Xu Liu Henggao Xiang Guang Chen National Key Laboratory of Advanced Casting Technologies MIIT Key Laboratory of Advanced Metallic and Intermetallic Materials TechnologyEngineering Research Center of Materials Behavior and DesignMinistry of EducationNanjing University of Science and TechnologyNanjing 210094China School of Aviation and Mechanical Engineering Changzhou Institute of TechnologyChangzhou 213032China

Heat-resistant aluminum alloys are widely used in aerospace and automotive fields for manufacturing hot components due to their advantages in lightweight design and energy ***,the high-temperature strength of existing cast aluminum alloys is always limited to about 100 MPa at 350℃due to coarsening and transformation of strengthening ***,we reveal that the yield strength and ultimate tensile strength of the T6 state Al-8.4Cu-2.3Ce-1.0Mn-0.5Ni-0.2Zr alloy at 400◦C increase by 34%and 44%after re-aging at 300℃for 100 h,and its thermal strength exhibits distinguished ad-vantage over traditional heat-resistant aluminum *** enhanced elevated-temperature strength is attributed to the reprecipitation of the Ni-bearing T-Al_(20)Cu_(2)Mn_(3)phase,whose number density increases over one *** significant segregation of Ni,Ce,and Zr elements at the interfaces helps improve the thermal stability of the T *** thermostable T phase effectively strengthens the matrix by in-hibiting dislocation ***,a highly interconnected 3D intermetallic network along the grain boundaries can still remain after long-term re-aging at 300℃,which is conducive to imposing a drag on the grain boundaries at high *** finding offers a viable route for enhancing the elevated-temperature strength of heat-resistant aluminum alloys,which could provide expanded opportunities for higher-temperature applications.

关键词： Aluminum alloys Precipitation Thermally reinforcement phase Re-aging treatment High-temperature strength

来源：评论

学校读者我要写书评

暂无评论

Mechanical behavior of TiAl alloys

引用

Science China(Technological Sciences) 2023年第9期66卷 2457-2480页

作者： XIANG HengGao CHEN Yang QI ZhiXiang ZHENG Gong CHEN FengRui CAO YueDe LIU Xu ZHOU Bing CHEN Guang National Key Laboratory of Advanced Casting Technologies MIIT Key Laboratory of Advanced Metallic and Intermetallic Materials TechnologyEngineering Research Center of Materials Behavior and DesignMinistry of EducationNanjing University of Science and TechnologyNanjing 210094China

Intermetallic TiAl alloys attract much attention in advanced engineering fields due to their low density(3.9–4.2 g/cm3) and excellent high-temperature properties. After more than half a century of research and development, TiAl alloys have found applications in aerospace, automotive, and related industries. However, as a kind of semi-brittle materials, intermetallic TiAl alloys exhibit different mechanical behavior from metallic and ceramic materials. Thus, it is necessary to systematically understand their mechanical behavior to ensure further developments and safe engineering applications. In this paper, the principal mechanical behavior of Ti Al alloys was reviewed comprehensively, including tension, creep, fatigue, and strengthening mechanisms. The mechanical performance and the corresponding deformation mechanisms are summarized and discussed in detail. The future directions of mechanical research on TiAl alloys are also overviewed to expedite their extensive utilization in engineering fields.

关键词： TiAl tension creep fatigue strengthening mechanisms

来源：评论

学校读者我要写书评

暂无评论

Strengthening and toughening bulk Ni_(2)CoFeV_(0.5) medium-entropy alloy via thermo-mechanical treatment

引用

Journal of Materials Science & technology 2023年第20期151卷 19-29页

作者： Lei Gu Rui Hou Yi Liu Guang Chen Jihua Liu Gong Zheng Ruisheng Zhang Yonghao Zhao National Key Laboratory of Advanced Casting Technologies MIIT Key Laboratory of Advanced Metallic and Intermetallic Materials TechnologyEngineering Research Center of Materials Behavior and DesignMinistry of EducationNanjing University of Science and TechnologyNanjing 210094China

Single-phase face-centered cubic(fcc)medium-and high-entropy alloys(MEAs/HEAs)have high ductility but low yield *** this work,the microstructures of single-phase fcc Ni_(2)CoFeV_(0.5) MEAs were tailored by cold-rolling and subsequent annealing and typical heterogeneous lamella(HL)structures composed of recrystallized micro-grain lamellae(with an averaged grain size of∼4μm)and nonrecrystallized nano-/ultrafine-grain lamellae were *** tests revealed that most HL samples exhibited excellent strength and ductility *** HL sample with∼23 vol%recrystallized grains annealed at 590℃ for 1 h had a high yield strength of 1120 MPa and a good fracture elongation of 12.3%,which increased by 5%and 46%,respectively compared with those of as-rolled ***-induced yield strength increase is attributed to high-density annealing twin boundaries(TBs)in the recrystallized grains,the annihilation of mobile dislocations inside the non-recrystallized grains,and extra heterodeformation-induced strengthening produced by the HL ***-Petch relationship of Ni_(2)CoFeV_(0.5) MEA can be reasonably described by counting both TBs and grain boundaries,with lattice friction stress of 87.3 MPa and coefficient of 722.8 MPaμm1/*** work provides optional and controllable solutions for preparing MEAs/HEAs with excellent mechanical properties by low-cost and high-efficiency thermomechanical treatments.

关键词： Medium-entropy alloys Microstructures Strength and ductility Heterogeneous lamella structure Cold-rolling Annealing

来源：评论

学校读者我要写书评

暂无评论

Strengthening in gradient TiAl alloys

引用

Journal of Materials Science & technology 2023年第35期166卷 98-105页

作者： P.Li Y.Chen X.Liu X.H.Wang F.R.Chen Z.X.Qi G.Zheng H.G.Xiang G.Chen National Key Laboratory of Advanced Casting Technologies MIIT Key Laboratory of Advanced Metallic and Intermetallic Materials TechnologyEngineering Research Center of Materials Behavior and DesignMinistry of EducationNanjing University of Science and TechnologyNanjing210094China

Gradient structure is emerging as an effective strategy to fabricate metals with remarkable mechanical performance,but have not been verified in intermetallic compounds for high-temperature *** experiments and atomic simulations,we show that a typical intermetallic TiAl alloy with gra-dient structure has a significant strengthening effect both at room temperature and high *** room-temperature compressive strength of TiAl alloys with gradient grain obtained by additive man-ufacturing is 2.57 GPa,which is∼2.7 times as strong as that with equiaxed *** strengthening effect is attributed to more sessile dislocations in gradient structure caused by the intersections of mul-tiple slip systems in gradient *** importantly,the strengthening effect is still effective at high temperatures and the compressive strength is 1.28 GPa at 750°*** simulation results show that this strengthening effect is due to the increased Hirth dislocation at high *** study expands the applications of TiAl alloys for load-bearing structures and provides a new strategy for improving the strength of intermetallic compounds at both room temperature and high temperatures.

关键词： TiAl alloys Strengthening Gradient grain Additive manufacturing Molecular dynamics

来源：评论

学校读者我要写书评

暂无评论

A modified maxwell-pulse thermoplastic constitutive model of in-situ Ta-particle reinforced Zr-based bulk metallic glass composites

引用

Progress in Natural Science:Materials International 2024年第4期34卷 753-766页

作者： Pan Gong Zhuang Wang Guoqing Yu Maojun Li Xin Zhuo Xuefeng Tang Mao Zhang Lei Deng Junsong Jin A.A.Churakova Xinyun Wang State Key Laboratory of Materials Processing and Die & Mould Technology School of Materials Science and Engineering Huazhong University of Science and Technology State Key Laboratory of Advanced Design and Manufacturing Technology for Vehicle Hunan University Institute of Molecule and Crystal Physics Ufa Federal Research Center RAS

The impact of different Ta contents on the mechanical properties and thermoplastic forming ability of in-situ Taparticle reinforced Zr–Cu–Al–Ni bulk metallic glass composites was studied. The composition(Zr55Cu30Al10-Ni5)94Ta6with the best comprehensive performance was chose for a systematic investigation into its thermoplastic behavior in the supercooled liquid region（SLR）, with quantitative analysis conducted by the strain rate sensitivity index and activation volume. The steady-state flow stress and the stress overshoot intensity were augmented with deformation temperature decreasing, strain rate increasing, and the addition of the secondary phase, leading to a transition from Newtonian to non-Newtonian flow regime. The addition of the secondary phase deteriorated the rheological properties of the material. To solve the problem that the Maxwell-Pulse constitutive model showed an inability to accurately describe the steady-state flow process. A modified constitutive relationship, introducing the effect of the volume fraction of Ta particles on viscosity and elastic modulus in the steady-state flow process which was ignored in Maxwell-pulse model, was established. The fitting results of the true stress-strain curves of the modified Maxwell-pulse constitutive model were in better agreement with the experimental date than those of the Maxwell-pulse constitutive model, with higher prediction accuracy. The modified constitutive model well predicted the thermoplastic deformation behavior of(Zr55Cu30Al10Ni5)*** influence mechanism of Ta particles on the flow behavior was explained that Ta particles increased the viscosity of amorphous matrix, thereby hindering its flow and ultimately leading to an increase in flow stress.

关键词： Bulk metallic glass composites Supercooled liquid region Thermoplastic deformation Constitutive model Influence mechanism

来源：评论

学校读者我要写书评

暂无评论

Comprehensive Biomechanical Characterization of the Flexible Cat Spine via Finite Element Analysis,Experimental Observations,and Morphological Insights

引用

Journal of Bionic Engineering 2024年第6期21卷 2877-2892页

作者： Da Lu Xueqing Wu Yangyang Xu Shijia Zhang Le Zhang Xin Huang Baoqing Pei Beijing Key Laboratory for Design and Evaluation Technology of Advanced Implantable&Interventional Medical Devices Beijing Advanced Innovation Center for Biomedical EngineeringSchool of Biological Science and Medical EngineeringBeihang UniversityBeijing100083China Shenzhen Institute of Beihang University Shenzhen518000China

Felids,during intense activities such as jumping and sprinting,adjust their posture by twisting and stretching their body to disperse limb impact and minimize *** self-stabilization mechanism has garnered significant attention for inspiring biometric robot *** study investigates the flexibility and cushioning characteristics of a cat’s spine,focusing on its biomechanical properties.A high-fidelity 3D model was used to test the range of motion(ROM)under six conditions,simulate dorsiflexion to analyze stress *** torsional and compressive stiffness were tested by using five cat spinal *** flexibility principles of the flexible cat’s spine were explained via morphological *** indicate that the cat spine has the least rotational stiffness in axial rotation,followed by extension and lateral bending,with a compressive stiffness of 53.62±4.68 N/*** during dorsiflexion is evenly distributed across *** vertebrae heights account for 90.34%of total spinal length with a mean height-to-width ratio of ***’spines,with more articulations and elongated vertebrae,allow for significant twisting and bending,aiding in rapid body posture adjustments and impact *** biomechanical traits could inspire the design of robots for confined rescue operations.

关键词： Cat spine Biomechanical characterization Finite element analysis Morphological measurement Flexibility testing

来源：评论

学校读者我要写书评

暂无评论

Effect of Free-End Torsion on the Corrosion and Mechanical Properties for Mg-3Zn-0.2Ca Alloy

引用

Acta Metallurgica Sinica(English Letters) 2025年第1期38卷 59-70页

作者： Li-Lan Gao Jiang Ma Yan-Song Tan Xiao-Hao Sun Qi-Jun Gao De-Bao Liu Chun-Qiu Zhang Tianjin Key Laboratory for Advanced Mechatronic System Design and Intelligent Control School of Mechanical EngineeringTianjin University of TechnologyTianjin300384China National Demonstration Center for Experimental Mechanical and Electrical Engineering Education Tianjin University of TechnologyTianjin300384China School of Materials Science and Engineering Tianjin University of TechnologyTianjin300384China

Magnesium alloys with excellent degradability and biocompatibility are promising materials for biomedical implants,saving patients the burden of second ***,their mechanical properties and corrosion resistance are significantly below the requirements for implant *** study aims to improve the mechanical and corrosion resistance properties of Mg-3Zn-0.2Ca alloy by pre-torsion treatment,and find out the optimal shear *** rod-shaped Mg-3Zn-0.2Ca alloy specimens were pre-torsion treated at different torsion *** effect of free-end torsion on Mg-3Zn-0.2Ca alloy was characterized through microstructure analysis,mechanical testing,and corrosion ***-torsion treatment can refine grain and induce twins and dislocations in Mg-3Zn-0.2Ca *** surface hardness increases with the increase in torsion *** yield strength and ultimate strength initially increase and then decrease with increasing torsion angle,while ductility decreases with increasing torsion *** with a shear strain of 30%exhibit the highest tensile strength,reaching 284.78±10.62 MPa,with an elongation of 19.37±1.66%.Furthermore,they show a significant improvement in fatigue lives both before and after *** the stress amplitude is 120 MPa,the fatigue lives for specimens without pre-torsion treatment are 54,275 cycles and 4324 cycles before and after pre-corrosion,while they increased significantly to 92,015 cycles and 5050 cycles with the 30%shear strain,***,the 30%shear strain specimens show a significant reduction in corrosion *** conclusion,pre-torsion treatment can effectively modify the microstructure of Mg-3Zn-0.2Ca alloy,enhancing both mechanical properties and corrosion *** optimal shear strain for this improvement is 30%.This study provides a practical method to enhance the mechanical properties and corrosion resistance of Mg-3Zn-0.2Ca alloy,making it more suitable for biomedical implan

关键词： Magnesium alloy Pre-torsion Microstructure Mechanical property Corrosion resistance

来源：评论

学校读者我要写书评

暂无评论

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

请选择保存的检索档案：

请选择收藏分类：

通借通还

建议与咨询 留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

请选择保存的检索档案： 新增检索档案 确定 取消

请选择收藏分类： 新增自定义分类 确定 取消

通借通还

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

请选择保存的检索档案：

请选择收藏分类：