检索结果-内蒙古大学图书馆

Effect of whisker alignment on microstructure,mechanical and thermal properties of Mg-SiC_(w)/Cu composite fabricated by a combination of casting and severe plastic deformation(SPD)

引用

Journal of Magnesium and Alloys 2023年第3期11卷 966-980页

作者： Yinwei Wang Moslem Tayyebi Morteza Tayebi Mahdireza Yarigarravesh Shoufa Liu Hongwei Zhang School of Mechanical Engineering Xijing UniversityXi’anShaanxi 710123China Department of Materials Science and Engineering Shiraz University of TechnologyShirazIran Young Researchers and Elites Club Science and Research BranchIslamic Azad UniversityTehranIran Department of Civil Engineering Adjunct facultySharif University of TechnologyTehranIran

In this research,microstructure evaluation,mechanical properties and thermal conductivity of the Mg-SiC_(w)/Cu composite with laminar structure were *** this purpose,SiC whiskers were added to magnesium alloy by using stir-casting,then the Mg-SiC_(w)composite was bonded to copper layers by warm accumulative roll bonding(ARB).Based on the results of optical microscopy(OM)and scanning electron microscopy(SEM),SiC whiskers were well distributed in the magnesium matrix and they were aligned parallelly when the composites were plastically deformed at higher rolling ***,all layers remained continuous with localized necking ***,no intermetallic compounds and phases were detected by XRD and EDS *** from the significant effect of severe plastic deformation on mechanical properties,the findings of mechanical tests point to the usefulness of reinforcements in improving up to 60%microhardness,Young’s modulus,yield,and up to 41%tensile ***,thermal conductivities of composites increased by adding reinforcement and above all by increasing the number of rolling *** growth is attributed to the higher thermal diffusivity of copper and whiskers as well as the increased number of conductive layers within composite.

关键词： SiC whisker Warm accumulative roll bonding Stir-casting Thermal conductivity

来源：评论

学校读者我要写书评

暂无评论

π-Extended giant dimeric acceptor as a third component enables highly efficient ternary organic solar cells with efficiency over 19.2%

引用

Journal of Energy Chemistry 2024年第8期95卷 263-270,I0006页

作者： Mengran Peng Haotian Wu Liming Wu Jianhua Chen Ruijie Ma Qunping Fan Hua Tan Weiguo Zhu Hongxiang Li Junqiao Ding School of Chemical Science and Technology Yunnan UniversityKunming 650500YunnanChina Department of Electrical and Electronic Engineering Research Institute for Smart Energy(RISE)Guangdong-Hong Kong-Macao(GHM)Joint Laboratory for Photonic-Thermal-Electrical Energy Materials and DevicesThe Hong Kong Polytechnic UniversityKowloonHong Kong 999077China State Key Laboratory for Mechanical Behavior of Materials Xi’an Jiaotong UniversityXi’an 710049ShaanxiChina School of Materials Science and Engineering Jiangsu Engineering Laboratory of Light-Electricity-Heat Energy-Converting Materials and ApplicationsChangzhou UniversityChangzhou 213164JiangsuChina College of Polymer Science and Engineering State Key Laboratory of Polymer Materials EngineeringSichuan UniversityChengdu 610065SichuanChina

Ternary strategy with a suitable third component is a successful strategy to improve the photovoltaic performance of organic solar cells(OSCs).Very recently,Y-series based giant molecule acceptors or oligomerized acceptors have emerged as promising materials for achieving highly efficient and stable binary OSCs,while application as third component for ternary OSCs is *** a novelπ-extended giant dimeric acceptor,GDF,is developed based on central Y series core fusion and rigid BDT as linker,and then incorporated into the state-of-the-art PM1:PC6 system to construct ternary *** GDF has a near planar backbone,resulting in increasedπ-conjugation,excellent crystallinity,and good electron transport *** GDF is introduced into the PM1:PC6 system,it ensues in a cascade like the lowest unoccupied molecular orbitals(LUMO)energy level alignment,a complementary absorption band with PM1 and PC6,higher and balanced hole and electron mobility,slightly smaller domain size,and a higher exciton dissociation probability for PM1:PC6:GDF(1:1.1:0.1)blend *** a consequence,the PM1:PC6:GDF(1:1.1:0.1)ternary OSC achieves a champion PCE of 19.22%,with a significantly higher open-circuit voltage and short-circuit current density,compared to 18.45%for the PM1:PC6(1:1.2)binary *** findings show that employing aπ-extended giant dimeric acceptor as a third component significantly improves the photovoltaic performance of ternary OSCs.

关键词： Giant dimeric acceptor Third component Ternary organic solar cells

来源：评论

学校读者我要写书评

暂无评论

Tribological performance under different environments of Ti-C-N composite films for marine wear-resistant parts

引用

International Journal of Minerals,Metallurgy and materials 2023年第1期30卷 144-155页

作者： Hongbo Ju Rui Zhou Jing Luan Ch Sateesh Kumar Lihua Yu Junhua Xu Junfeng Yang Bowei Zhang Filipe Fernandes School of Materials Science and Engineering Jiangsu University of Science and TechnologyZhenjiang 212003China CEMMPRE—Centre for Mechanical Engineering Materials and Processes Department of Mechanical EngineeringUniversity of CoimbraCoimbra 3030-788Portugal CFAA University of the Basque Country UPV/EHUBilbao 48170Spain ISEP-School of Engineering Polytechnic of PortoPorto 4200-072Portugal Key Laboratory of Materials Physic Institute of Solid State PhysicsHefei Institute of Physical SciencesChinese Academy of SciencesHefei 230031China Institute for Advanced Materials and Technology University of Science and Technology BeijingBeijing 100083China

The need for reducing the wear in mechanical parts used in the industry makes self-lubricant films one of the sustainable solutions to achieve long-term protection under different environmental *** purpose of this work is to study the influence of C additions on the tribological behavior of a magnetron-sputtered TiN film in air,water,and *** results show that the addition of C into the TiN binary film induced a new amorphous phase,and the films exhibited a dual phase of fcc(face-centered cubic)-TiN and amorphous *** antifriction and wear-resistance properties were enhanced in air and water by adding 19.1at%***,a further increase in the C concentration improved anti-frictional properties but also led to higher wear *** the amorphous phase induced microbatteries and accelerated the corrosion of TiN phases in seawater,the negative abrasion state was detected for all Ti-C-N films due to the adhesion of the tribocorrosion debris on the wear track.

关键词： RF reactive magnetron sputtering Ti-C-N films microstructure tribological properties in air/water/seawater

来源：评论

学校读者我要写书评

暂无评论

Electrical, mechanical and damage self-sensing properties of basalt fiber reinforced polymer composites modified by electrophoretic deposition

引用

Progress in Natural science:materials International 2023年第5期33卷 593-600页

作者： Haoming Sun Dong Xiang Jie Zhang Wei Tan Eileen Harkin-Jones Junjie Wang Menghan Wang Bin Wang Chunxia Zhao Hui Li Zhenyu Li Yuntao Li Yuanpeng Wu School of New Energy and Materials Southwest Petroleum University The Center of Functional Materials for Working Fluids of Oil and Gas Field Sichuan Engineering Technology Research Center of Basalt Fiber Composites Development and Application Southwest Petroleum University Collaborative Scientific Innovation Platform of Universities in Sichuan for Basalt Fiber Southwest Petroleum University School of Mechanical Engineering Southwest Petroleum University School of Engineering and Materials Science Queen Mary University of London School of Engineering Ulster University Department of Civil Engineering Tsinghua University College of Materials Science and Engineering Chongqing University

In this work, basalt fiber reinforced polymer(BFRP) with enhanced electrical, mechanical properties and in-situ damage self-sensing capability was prepared using carboxylic carbon nanotubes(COOH-CNTs) modified BF fabrics via electrophoretic deposition(EPD) at different voltages. The BFRP with BF fabrics modified at a deposition voltage of 20 V(EPD20-BFRP) showed the lowest electrical resistivity. Compared with unmodified BFRP, the tensile and flexual moduli of EPD20-BFRP increased by 37.5 % and 14.9 %, respectively. Single-layer EPD20-BFRP exhibited a high gauge factor(GF) of 44.3 during tensile damage self-sensing. The acoustic emission(AE) signals during tensile and flexual damage process agreed well with the relative resistance changes(RRC),which confirmed different damage stages within loading process, such as elastic deformation, damage evolution,crack coalescence, and complete fracture. In addition, the multi-layer BFRP containing a single-layer EPD20-BFRP on the upper or lower surface of laminate exhibited distinct electrical signal responses subjected to the flexural loading.

关键词： Carbon nanotubes and nanofibers Natural fibers Polymer-matrix composites (PMCs) Non-destructive testing

来源：评论

学校读者我要写书评

暂无评论

Precision Enhancement in Tough Polylactic Acid Material Extrusion: A Systematic Response Surface Investigation for Sustainable Manufacturing

SAE International journal of Sustainable Transportation, Ene...

引用

SAE International journal of Sustainable Transportation, Energy, Environment, and Policy 2024年第3期5卷

作者： Moradi, Mahmoud Rezayat, Mohammad Meiabadi, Saleh Rasoul, Fakhir A. Shamsborhan, Mahmoud Casalino, Giuseppe Karamimoghadam, Mojtaba University of Northampton United Kingdom Department of Materials Science and Engineering Spain Politècnica de Catalunya-BarcelonaTECH Barcelona Research Center in Multiscale Science and Engineering Spain École de Technologie Supérieure Department of Mechanical Engineering Canada Al-Kitab University Department of Air-Conditioning and Refrigeration Technical Engineering College of Technical Engineering Iraq Islamic Azad University Mechanical Engineering Department Iran Polytechnic University of Bari Department of Mechanics Mathematics and Management Italy

This research systematically explores the significant impact of geometrical dimensions within fused deposition modeling (FDM), with a focus on the influence of raster angle and interior fill percentage. Through meticulous experimentation and the application of response surface modeling (RSM), the influence on critical parameters such as weight, length, width at ends, width at neck, thickness, maximum load, and elongation at tensile strength is thoroughly analyzed. The study, supported by ANOVA, highlights the notable effects of raster angle and interior fill percentage, particularly on width at ends, width at neck, and thickness. During the optimization phase, specific parameters - precisely, a raster angle of 31.68 and an interior fill percentage of 27.15 - are identified, resulting in an exceptional desirability score of 0.504. These insights, substantiated by robust statistical data, fill a critical gap in the understanding of 3D-printed parts, offering practical recommendations for superior mechanical performance across diverse applications. © 2024 SAE International.

关键词： Tensile strength

来源：评论

学校读者我要写书评

暂无评论

3D/4D additive-subtractive manufacturing of heterogeneous ceramics

引用

Journal of materials science & Technology 2024年第34期201卷 210-221页

作者： Guo Liu Xinya Lu Xiaofeng Zhang Yan Zhao Shenghui Yi Jingjun Xu Yuqi Zhan Jianan Yin Chengcheng Feng Zhifeng Zhou Peiyu Wang Zhou Chen Yunhu He Siyao Chen Pengchao Liu Jun Zuo Yu Dai Jian Wu Sida Liu Jian Lu Centre for Advanced Structural Materials City University of Hong Kong Shenzhen Research InstituteGreater Bay Joint DivisionShenyang National Laboratory for Materials ScienceShenzhen 518057China CityU-Shenzhen Futian Research Institute Shenzhen 518045China Hong Kong Branch of National Precious Metals Material Engineering Research Center City University of Hong KongHong Kong 999077China Department of Mechanical Engineering City University of Hong KongHong Kong 999077China Department of Materials Science and Engineering City University of Hong KongHong Kong 999077China National Engineering Laboratory for Modern Materials Surface Engineering Technology&The Key Lab of Guangdong for Modern Surface Engineering Technology Institute of New MaterialsGuangdong Academy of ScienceGuangzhou 510650China State Key Laboratory of Advanced Design and Manufacturing for Vehicle Body College of Mechanical and Vehicle EngineeringHunan UniversityChangsha 410082China Faculty of Materials Science Shenzhen MSU-BIT UniversityShenzhen 518100China Shenyang National Laboratory for Materials Science Institute of Metal ResearchChinese Academy of SciencesShenyang 110016China School of Physics and Materials Nanchang UniversityNanchang 330031China

The manufacturing of heterogeneous high-temperature material components is challenging for use in practical ***-dimensional(3D)printing provides solutions to programmable constructing ceramic ***,the development of heterogeneous ceramics is limited by low flexibil-ity of heterogeneity,geometrical complexity,structural resolution,manufacturing efficiency,and mate-rial *** this study,we demonstrated flexible and rapid approaches for fabricating complicated and precise heterogeneous ceramics by shape-changing(4D)or shape-keeping(3D)additive-subtractive manufacturing(ASM)*** shape-changing strategy for heterogeneous ceramics was achieved by global ceramization of heterogeneous precursors,while the shape-keeping strategy for heterogeneous ceramics was achieved by local receramization of homogeneous *** element analysis(FEA)simulations of the influence of the thermal shrinkage dominant in the shape-changing strategy on the shape deformation of heterogeneous ceramics could be valuable predictions of the experimental *** 3D/4D ASM methods are generic for high-temperature materials and extendable to metallic and dia-mond materials.

关键词： 3D/4D printing Additive-subtractive manufacturing Heterogeneous ceramics Elastomer-derived ceramics Local receramization

来源：评论

学校读者我要写书评

暂无评论

COMPREHENSIVE REVIEW OF DIC AND XCT TECHNOLOGIES IN EVALUATING CONCRETE STRUCTURAL INTEGRITY AND DURABILITY

COMPREHENSIVE REVIEW OF DIC AND XCT TECHNOLOGIES IN EVALUATI...

引用

ASME 2024 International mechanical engineering Congress and Exposition, IMECE 2024

作者： Azari, Fatemeh Jazaei, Robabeh Department of Mechanical Engineering and Materials Science College of Engineering University of Pittsburgh PittsburghPA United States Department of Engineering College of Engineering and Science Slippery Rock University Slippery RockPA United States

ISBN: (纸本)9780791888612

The deteriorating concrete infrastructure in the U.S., notably highways and bridges, urgently needs attention. The department of Transportation and various assessments highlight a maintenance deficit exacerbating traffic congestion [1]. An investment of about $3.6 trillion [1,2] is required to rectify these issues and improve traffic flow, emphasizing the need for stronger, more durable composite materials for concrete [2].Recent advances in high-resolution optical imaging, especially X-ray Computed Tomography (CT), have become crucial in materials science [3]. CT imaging offers in-depth insights into the internal structure of concrete, essential for understanding crack development and propagation under environmental stresses like earthquakes [4]. This technology has transformed the assessment of concrete's mechanical properties, such as stress behaviors and deformation [4,5]. Improved CT imaging significantly enhances computational modeling, facilitating precise integration of geometric models into advanced finite element analysis software, thus improving the durability and longevity of concrete infrastructures [6, 7]. This paper provides a comprehensive review of the applications, progress, and limitations of CT imaging in concrete material analysis [6-8]. It underscores the significance of these imaging techniques in enhancing the structural performance of concrete, contributing to the resilience and sustainability of critical infrastructure systems [7-9]. This review aims to foster a deeper understanding of material behaviors and drive innovations in concrete technology. Copyright © 2024 by ASME.

关键词： Traffic congestion

来源：评论

学校读者我要写书评

暂无评论

Grain-refining Co_(0.85)Se@CNT cathode catalyst with promoted Li_(2)O_(2)growth kinetics for lithium-oxygen batteries

引用

Chinese Chemical Letters 2024年第12期35卷 304-310页

作者： Ruonan Yang Jiajia Li Dongmei Zhang Xiuqi Zhang Xia Li Han Yu Zhanhu Guo Chuanxin Hou Gang Lian Feng Dang School of Materials Science&Engineering State Key Laboratory of Crystal MaterialsShandong UniversityJi’nan 250061China Integrated Composites Lab Department of Mechanical and Construction EngineeringNorthumbria UniversityNewcastle Upon TyneNE18STUnited Kingdom School of Environmental and Material Engineering Yantai UniversityYantai 264005China

Highly active cathode catalysts for efficient formation/decomposition of Li_(2)O_(2)are essential for the performance improvement of lithium-oxygen batteries(LOBs).In this study,a grain-refining Co_(0.85)Se catalyst with a lattice spacing of 2.69 A of(101)plane closely matching with the(100)plane(2.72A)of Li_(2)O_(2)was applied for high-performance ***(101)plane exposed Co_(0.85)Se@CNT was synthesized by a simple one-pot hydrothermal *** Co_(0.85)Se with the lattice matching effect not only led to the efficient conversion and polarized growth of Li_(2)O_(2),but also prevented the formation of *** functional theory(DFT)calculations reveal that Co_(0.85)Se(101)plane has the intrinsic catalytic ability to generate/decompose Li_(2)O_(2)during ORR/OER process,due to its homogeneous electron distribution,suitable adsorption energy,and promoted Li_(2)O_(2)growth *** a consequence,the(101)plane highly exposed Co_(0.85)Se@CNT-80 electrode exhibited remarkable cycle stability over 2400 h at 100 mA/g and 290cycles at 500 mA/g,which is about 2 times longer than other electrodes.

关键词： Lithium-oxygen batteries Co_(0.85)Se@CNT Cathode catalysts Grain-refiner DFT calculation

来源：评论

学校读者我要写书评

暂无评论

Synergistically Improved mechanical Properties and Thermal Conductivity of Hypoeutectic AlSiNiFeMg Alloy Prepared by Ultrasonic-assisted Casting

引用

Journal of Wuhan University of Technology(materials science) 2024年第6期39卷 1565-1568页

作者： ZHANG Wenda YUAN Xuan ZHOU Yuli ZHONG Gu BAI Peikang WANG Hongfu LIU Jun School of Materials Science and Engineering North University of ChinaTaiyuan 030051China Chinalco Materials Application Research Institute Co. Ltd.Suzhou BranchSuzhou 215026China Department of Materials Science and Engineering University of Science and Technology BeijingBeijing 100083China Standard&Quality Control Research Institute Ministry of Water ResourcesHangzhou 310024China School of Mechanical Engineering North University of ChinaTaiyuan 030051China Delta Aluminum Corporation in Zhaoqing Zhaoqing 526029China

We employed a melt ultrasonic treatment near the liquidus to prepare a high-thermal-conductivity Al-4Si-2Ni-0.8Fe-0.4Mg *** influences of various ultrasonic powers on its microstructure,mechanical properties,and thermal conductivity were *** is shown that near-liquidus ultrasonication significantly refines the alloy grains and eutectic structure,synergistically improving the alloy’s mechanical properties and thermal ***,the grain size decreased by 84.5%from 941.4 to 186.2μ*** the ultrasonic power improved the thermal conductivity of the alloy slightly and significantly enhanced its mechanical *** an ultrasonic power of 2100 W,the tensile strength,yield strength,elongation rate,and thermal conductivity were 216 MPa,142 MPa,6.3%,and 169 W/(m·k),respectively.

关键词： Al-Si alloy mechanical property thermal conductivity ultrasonic treatment solidification microstructure

来源：评论

学校读者我要写书评

暂无评论

Kinetic investigation of the energy storage process in graphene fiber supercapacitors:Unraveling mechanisms,fabrications,property manipulation,and wearable applications

引用

Carbon Energy 2025年第1期7卷 133-173页

作者： Juan Zhang Wenwen Liu Minzhi Du Qingli Xu Minren Hung Ruifang Xiang Meng Liao Xinhou Wang Bingjie Wang Aiping Yu Kun Zhang Key Laboratory of Textile Science and Technology(Donghua University) Ministry of EducationCollege of TextilesDonghua UniversityShanghaiChina Department of Chemical Engineering Waterloo Institute for NanotechnologyUniversity of WaterlooWaterlooONCanada Laboratory of Advanced Materials State Key Laboratory of Molecular Engineering of PolymersDepartment of Macromolecular ScienceFudan University2205 Songhu RdShanghai 200438China College of Mechanical Engineering Donghua UniversityShanghai 201620China

Graphene fiber supercapacitors(GFSCs)have garnered significant attention due to their exceptional features,including high power density,rapid charge/discharge rates,prolonged cycling durability,and versatile weaving ***,inherent challenges in graphene fibers(GFs),particularly the restricted ion-accessible specific surface area(SSA)and sluggish ion transport kinetics,hinder the achievement of optimal capacitance and rate *** existing reviews on GFSCs,a notable gap exists in thoroughly exploring the kinetics governing the energy storage process in *** review aims to address this gap by thoroughly analyzing the energy storage mechanism,fabrication methodologies,property manipulation,and wearable applications of *** theoretical analysis of the energy storage process,specific parameters in advanced GF fabrication methodologies are carefully summarized,which can be used to modulate nano/micro-structures,thereby enhancing energy storage *** particular,enhanced ion storage is realized by creating more ion-accessible SSA and introducing extra-capacitive components,while accelerated ion transport is achieved by shortening the transport channel length and improving the accessibility of electrolyte *** on the established structure-property relationship,several critical strategies for constructing optimal surface and structure profiles of GF electrodes are *** on the exceptional flexibility and wearability of GFSCs,the review further underscores their potential as foundational elements for constructing multifunctional e-textiles using conventional textile *** conclusion,this review provides insights into current challenges and suggests potential research directions for GFSCs.

关键词： fiber-shaped supercapacitor graphene ion storage ion transport wearable application

来源：评论

学校读者我要写书评

暂无评论

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

请选择保存的检索档案：

请选择收藏分类：

通借通还

建议与咨询 留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

请选择保存的检索档案： 新增检索档案 确定 取消

请选择收藏分类： 新增自定义分类 确定 取消

通借通还

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

请选择保存的检索档案：

请选择收藏分类：