检索结果-内蒙古大学图书馆

7th International Conference on Intelligent Robotics and control engineering, IRCE 2024

作者： Li, Mingqun Lei, Yongjun Jiang, Qinghua Beijing Institute of Control Engineering Research and Development Center Beijing China Beijing Institute of Control Engineering System Design Department Beijing China

ISBN: (纸本)9798350352399

XX-1 satellite is a micro-nano satellite with low control system redundancy, equipped with only one set of three-axis gyroscopes. How to achieve attitude control during satellite failures has become an important issue in control scheme. This article proposes an attitude control scheme for low redundancy micro-nano satellites under the condition of no gyroscope. When high-value components in the satellite attitude control system, such as gyroscopes, fail and there are no redundant components, the satellite only uses magnetometers to reconstruct the attitude determination system, which can achieve attitude determination under any attitude conditions. This paper divides the working modes of micro-nano satellites into different modes based on the control tasks. Corresponding control laws are adopted in different modes, and magnetic torquers and momentum wheels are used to generate corresponding control torques, thus forming a complete satellite attitude control scheme. This paper further proposes effective discrimination conditions and parameter design methods for various working modes. Mathematical simulation shows that the proposed scheme enables micro-nano satellites to recover from any attitude to a stable operating state without gyroscope, and has the ability to operate stably in orbit for a long time. The attitude control accuracy is better than 2°, and the attitude stability is better than 0.003°/s, greatly improving the satellite's ability to operate safely in orbit. © 2024 IEEE.

关键词： Gyroscopes

来源：评论

学校读者我要写书评

暂无评论

A Method of Magnetometer Relative Reference Calibration for Micro-Nano Satellite and Its Application in Orbit 6

A Method of Magnetometer Relative Reference Calibration for ...

引用

6th International Conference on Intelligent Robotics and control engineering, IRCE 2023

作者： Li, Mingqun Liu, Xiang Chen, Shangshang Ma, Kun Jiang, Qinghua Research and Development Center Beijing Institute of Control Engineering Beijing China Beijing Institute of Control Engineering System Design Department Beijing China

ISBN: (纸本)9798350326338

For a low-cost micro-nano satellite that uses magnetometer as the core sensor of attitude determination system, a calibration method of relative reference between multiple magnetometer is proposed. The influence of satellite magnetic environment on magnetic field intensity measurement is studied. After considering remanence, induction and installation deviation, an accurate measurement model of magnetometer is proposed. Without introducing other high-performance attitude sensors, the relative relationship between the measurement data of different magnetometer is derived, and a magnetometer relative reference calibration method based on the least square method is proposed. Mathematical simulation shows that the proposed method reduces the relative measurement error of the magnetometer from 2000 nT to 50 nT, and then uses the telemetry data of the satellite in orbit to calibrate several magnetometer of the satellite. After injecting new parameters, the attitude difference of satellites with different magnetometer as the reference decreases from 16 degrees to less than 2 degrees, indicating that the consistency of the magnetometer reference has been significantly improved, which verifies the effectiveness and practicality of the proposed method. © 2023 IEEE.

关键词： Calibration

来源：评论

学校读者我要写书评

暂无评论

Knowledge and data jointly driven aeroengine gas path performance assessment method

引用

Chinese Journal of Aeronautics 2024年第5期37卷 533-557页

作者： Zhe WANG Xuyun FU Rui ZHANG Zhengfeng BAI Xiangzhao XIA Wei JIANG Department of Mechanical Engineering Harbin Institute of TechnologyWeihai 264209China Weihai Key Laboratory of Intelligent Operation and Maintenance Harbin Institute of TechnologyWeihai 264209China Control System Design Laboratory AECC ShenYang Engine Research InstituteShenyang 110015China

Aeroengines,as the sole power source for aircraft,play a vital role in ensuring flight *** gas path,which represents the fundamental pathway for airflow within an aeroengine,directly impacts the aeroengine's performance,fuel efficiency,and ***,timely and accurate evaluation of gas path performance is of paramount *** paper proposes a knowledge and data jointly driven aeroengine gas path performance assessment method,combining Fingerprint and gas path parameter deviation ***,Fingerprint is used to correct gas path parameter deviation values,eliminating parameter shifts caused by non-component performance ***,coarse errors are removed using the Romanovsky criterion for short-term data divided by an equal-length overlapping sliding ***,an Ensemble Empirical Mode Decomposition and Non-Local Means(EEMD-NLM)filtering method is designed to“clean”data noise,completing the preprocessing for gas path parameter deviation ***,based on the characteristics of gas path parameter deviation values,a Dynamic Temporary Blended Network(DTBN)model is built to extract its temporal features,cascaded with Multi-Layer Perceptron(MLP),and combined with Fingerprint to construct a Dynamic Temporary Blended AutoEncoder(DTB-AutoEncoder).Eventually,by training this improved autoencoder,the aeroengine gas path multi-component performance assessment model is formed,which can sufficiently decouple the nonlinear mapping relationship between aeroengine gas path multi-component performance degradation and gas path parameter deviation values,thereby achieving the performance assessment of engine gas path *** practical application cases,the effectiveness of this model in assessing the aeroengine gas path multi-component performance is verified.

关键词： Performance assessment Aeroengine Fingerprint Gas path parameter deviation values Jointly drive

来源：评论

学校读者我要写书评

暂无评论

Error Dependent Sampling to Reduce Transient Events in Event Based control 3

Error Dependent Sampling to Reduce Transient Events in Event...

引用

3rd IEEE Industrial Electronics Society Annual On-Line Conference, ONCON 2024

作者： Miguel-Escrig, Oscar Romero-Perez, Julio-Ariel Sanchez-Moreno, Jose Dormido-Bencomo, Sebastian Universitat Jaume I Department of System Engineering and Design Castelló de la Plana Spain Department of Computer Science and Automatic Control Madrid Spain

ISBN: (纸本)9798331540319

One of the objectives of event-based control is the reduction of generated events to perform an appropriate process control. Among the event generation techniques used to this end, those quantifying the error signal can be found more frequently for its simplicity of implementation. However, they entail a drawback in the form of trade-off between event generation and performance. Aiming to reduce the number of events, specifically in the transient response, without degrading the performance, an error dependent sampling scheme is studied in this work. © 2024 IEEE.

关键词： Electromagnetic transients

来源：评论

学校读者我要写书评

暂无评论

A Hybrid Temporal-Magnitude Based Sampling for Event-Based control 3

A Hybrid Temporal-Magnitude Based Sampling for Event-Based C...

引用

3rd IEEE Industrial Electronics Society Annual On-Line Conference, ONCON 2024

作者： Miguel-Escrig, Oscar Sanchez-Moreno, Jose Romero-Perez, Julio-Ariel Dormido-Bencomo, Sebastian Universitat Jaume I Department of System Engineering and Design Castelló de la Plana Spain Department of Computer Science and Automatic Control Madrid Spain

ISBN: (纸本)9798331540319

In the current industrial environment, which is shifting towards an event-based control prone paradigm, sampling strategies in use must be revisited. Both temporal and magnitude dependent sampling strategies have been demonstrated to be suitable for control systems, reporting benefits in different categories. However, these sampling strategies also present some drawbacks, discussed in this contribution. Aiming to address some of these drawbacks, a new sampling strategy is proposed gathering characteristics of both predecessors. © 2024 IEEE.

关键词： Decentralized control

来源：评论

学校读者我要写书评

暂无评论

An Integrated Calibration Scheme for Attitude Benchmark of Micro-nano Satellites and Its Experiments Based on In-Orbit Data 8

An Integrated Calibration Scheme for Attitude Benchmark of M...

引用

8th International Conference on Automation, control and Robotics engineering, CACRE 2023

作者： Li, Mingqun Luo, Tong Wang, Shaokai Li, He Lei, Yongjun Jiang, Qinghua Beijing Institute of Control Engineering Research and Development Center Beijing China Beijing Institute of Control Engineering System Design Department Beijing China Beijing Institute of Control Engineering Software Development Department Beijing China

ISBN: (纸本)9798350302776

The integrated calibration method of micro-nano satellite attitude benchmark is studied. Considering the magnetic effects and residual magnetism caused by the complex magnetic environment of the satellite, an accurate measurement model for magnetometers was adopted. By using the relationship between the measured and theoretical values of the geomagnetic field, the residual magnetism and magnetic sensitivity coefficients in the magnetometer measurement model were calibrated, through the least square method of uncertain parameters of the calibration. After modeling the installation error of the solar sensor, the calibration of the solar sensor is completed, so as to realize the integrated calibration of the attitude benchmark of the micro-nano satellite. Finally, this article conducted ground experiments using telemetry data from an in orbit satellite. The experimental results showed that the proposed method reduced sensor measurement errors, improved sensor benchmark consistency, and improved attitude determination accuracy from around 10 degrees to better than 0.2 degrees, verifying the effectiveness of the proposed method. © 2023 IEEE.

关键词： Calibration

来源：评论

学校读者我要写书评

暂无评论

Perturbation Event Oriented Dynamic Task Scheduling Algorithm for Parallel Testing of control systems

Perturbation Event Oriented Dynamic Task Scheduling Algorith...

引用

2024 IEEE International Conference on Sensing, Diagnostics, Prognostics, and control, SDPC 2024

作者： Chen, Jingyi Wang, Shenhang Tong, Xiaoxuan Xiang, Gang Yu, Yang Zhan, Ziyuan School of Electronic and Information Engineeer Harbin Institute of Technology Harbin China Beijing Aerospace Automatic Control Institute System Design Department Beijing China Beijing Aerospace Automatic Control Institute Beijing China Beijing Aerospace Automatic Control Institute Department of System Engineering Beijing China

ISBN: (纸本)9798350388855

Task scheduling algorithms are key to research and practice in parallel testing techniques, especially in control system applications. The complexity of control system testing requires higher scheduling efficiency. However, perturbation events caused by test equipment problems, data transmission obstacles, or task changes are almost unavoidable and may reduce the scheduling effectiveness or even lead to system crashes. Therefore, in this paper, based on the analysis of the dynamic test scheduling model, a disturbance factor is designed to judge the urgency of disturbance events for evaluating the dynamic scheduling cycle. On this basis, based on the comprehensive rescheduling index, a suitable adjustment strategy is selected to formulate the dynamic test scheduling scheme. The experimental results show that the algorithm proposed in this paper can achieve fast response capability for different disturbance events and exhibit good adaptivity. © 2024 IEEE.

关键词： Scheduling algorithms

来源：评论

学校读者我要写书评

暂无评论

A theoretical and deep learning hybrid model for predicting surface roughness of diamond-turned polycrystalline materials

引用

International Journal of Extreme Manufacturing 2023年第3期5卷 620-644页

作者： Chunlei He Jiwang Yan Shuqi Wang Shuo Zhang Guang Chen Chengzu Ren Tianjin Key Laboratory of Equipment Design and Manufacturing Technology Department of Mechanical EngineeringTianjin UniversityTianjin 30054People’s Republic of China Department of Mechanical Engineering Keio UniversityYokohama 223-8522Japan Tianjin Key Laboratory of the Design and Intelligent Control of the Advanced Mechatronical System School of Mechanical EngineeringTianjin University of TechnologyTianjin 300384People’s Republic of China School of Mechanical Engineering Yanshan UniversityQinhuangdao 066004People’s Republic of China

Polycrystalline materials are extensively employed in *** surface roughness significantly affects the working *** defects,particularly grain boundaries,have a great impact on the achieved surface roughness of polycrystalline ***,it is difficult to establish a purely theoretical model for surface roughness with consideration of the grain boundary effect using conventional analytical *** this work,a theoretical and deep learning hybrid model for predicting the surface roughness of diamond-turned polycrystalline materials is *** kinematic–dynamic roughness component in relation to the tool profile duplication effect,work material plastic side flow,relative vibration between the diamond tool and workpiece,etc,is theoretically *** material-defect roughness component is modeled with a cascade forward neural *** the neural network,the ratio of maximum undeformed chip thickness to cutting edge radius RT S,work material properties(misorientation angle θ_(g) and grain size d_(g)),and spindle rotation speed n s are configured as input *** material-defect roughness component is set as the output *** validate the developed model,polycrystalline copper with a gradient distribution of grains prepared by friction stir processing is machined with various processing parameters and different diamond *** with the previously developed model,obvious improvement in the prediction accuracy is observed with this hybrid prediction *** on this model,the influences of different factors on the surface roughness of polycrystalline materials are *** influencing mechanism of the misorientation angle and grain size is quantitatively *** fracture modes,including transcrystalline and intercrystalline fractures at different RTS values,are ***,optimal processing parameters are obtained with a simulated annealing *** experiments are performed with

关键词： diamond turning material-defect roughness component polycrystalline copper neural network simulated annealing algorithm

来源：评论

学校读者我要写书评

暂无评论

Effects of ultrasonic vibration parameters on the cutting force, chip morphology, and bone cracking in bovine cortical bone milling

引用

International Journal of Abrasive Technology 2024年第4期12卷 293-312页

作者： Hu, Yahui Zhong, Jie He, Lingrui Lin, Yize Zhang, Zhaoxiong Zhang, Chunqiu Fu, Weihua Tianjin Key Laboratory for Advanced Mechatronic System Design and Intelligent Control School of Mechanical Engineering National Demonstration Center for Experimental Mechanical and Electrical Engineering Education Tianjin University of Technology Tianjin300384 China Department of General Surgery Tianjin Medical University General Hospital Tianjin300052 China

Ultrasonic vibration-assisted technology is employed in orthopaedic surgery to minimise invasive effects in bone milling. This study explored the motion characteristics of ultrasonic vibration-assisted milling (UVAM), its intermittent cutting phenomenon, and tool-bone contact and separation times, via the developed experimental platform. The UVAM and conventional milling (CM) tests were carried out on bovine cortical bones with measurement of respective cutting forces and scanning electron microscope (SEM) observation of crack initiation and propagation in the milled bones. The UVAM application improved the chip-breaking ability of the milling tool and reduced the bone-milling force by 15.90%–25.06% compared to CM. Properly adjusting ultrasonic frequency and amplitude made it possible to reduce the bone cracking effect and enhance the milled bone surface quality. Copyright © 2024 Inderscience Enterprises Ltd.

关键词： Mammals

来源：评论

学校读者我要写书评

暂无评论

A generative deep learning framework for inverse design of compositionally complex bulk metallic glasses

引用

npj Computational Materials 2023年第1期9卷 2196-2203页

作者： Ziqing Zhou Yinghui Shang Xiaodi Liu Yong Yang Department of Mechanical Engineering College of EngineeringCity University of Hong KongKowloon TongKowloonHong KongChina City University of Hong Kong(Dongguan) 523000 DongguanChina College of Mechatronics and Control Engineering Shenzhen University518060 ShenzhenChina Department of Materials Science and Engineering College of EngineeringCity University of Hong KongKowloon TongKowloonHong KongChina Department of Advanced Design and System Engineering College of EngineeringCity University of Hong KongKowloon TongKowloonHong KongChina

The design of bulk metallic glasses(BMGs)via machine learning(ML)has been a topic of active research ***,the prior ML models were mostly built upon supervised learning algorithms with human inputs to navigate the high dimensional compositional space,which becomes inefficient with the increasing compositional complexity in ***,we develop a generative deep-learning framework to directly generate compositionally complex BMGs,such as high entropy *** framework is built on the unsupervised Generative Adversarial Network(GAN)algorithm for data generation and the supervised Boosted Trees algorithm for data *** studied systematically the confounding effect of various data descriptors and the literature data on the effectiveness of our framework both numerically and *** importantly,we demonstrate that our generative deep learning framework is capable of producing composition-property mappings,therefore paving the way for the inverse design of BMGs.

关键词： inverse metallic entropy

来源：评论

学校读者我要写书评

暂无评论

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

请选择保存的检索档案：

请选择收藏分类：

通借通还

建议与咨询 留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

请选择保存的检索档案： 新增检索档案 确定 取消

请选择收藏分类： 新增自定义分类 确定 取消

通借通还

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

请选择保存的检索档案：

请选择收藏分类：