检索结果-内蒙古大学图书馆

8th International Conference on Fibre-Reinforced Polymer (FRP) Composites in Civil Engineering, CICE 2016

作者： Wang, Zhenyu Cai, Zhongkui Key Lab of Structures Dynamic Behavior and Control of the Ministry of Education Harbin Institute of Technology Harbin150090 China School of Civil Engineering Harbin Institute of Technology Harbin150090 China

ISBN: (纸本)9789881448026

The rapid construction nature and outstanding self-centring ability make the post-tensioned precast segmental (PTPS) bridge pier a promising alternative to traditional cast-in-place piers. In this paper, PTPS piers reinforced with both steel and fibre reinforced polymer (FRP) bars were numerically analyzed. This type of pier is referred to as a hybrid bars reinforced PTPS bridge pier in this paper. The steel bars which continuously cross the segment joints (referred to as ED bars) were expected to improve the energy dissipation ability of the PTPS piers, while the FRP bars were expected to increase the post-yield stiffness and to decrease the residual displacement. Monotonic and cyclic analyses on hybrid bars reinforced PTPS piers were subsequently conducted. Three parameters were investigated, namely, the mechanical properties of FRP bars, the FRP bar reinforcement ratio and the proportion of FRP bars to ED bars. According to the analysis results in this study, the FRP bars are effective on improving the self-centring ability of the hybrid bars reinforced PTPS piers. Copyright © 2016 Department of Civil and Environmental Engineering & Research Institute for Sustainable Urban Development, The Hong Kong Polytechnic University.

关键词： Energy dissipation

来源：评论

学校读者我要写书评

暂无评论

Modeling of the effect of water ingress on the bond between carbon fiber – Epoxy resin with the molecular dynamics technique 8

Modeling of the effect of water ingress on the bond between ...

引用

8th International Conference on Fibre-Reinforced Polymer (FRP) Composites in Civil Engineering, CICE 2016

作者： Xiao, Yanrong Xian, Guijun Li, Hui Key Lab of Structural Dynamic Behavior and Control of the Ministry of Education Harbin Institute of Technology Harbin150090 China Harbin150090 China

ISBN: (纸本)9789881448026

FRP (fiber reinforced polymer) has taken advantages of the fiber reinforcement and resin matrix, possessing excellent mechanical properties and corrosive resistances, even in harsh environments. The lack of the knowledge of the durability performances of FRPs in various environmental conditions and the related degradation mechanisms of FRPs leads to significantly conservative design. Water ingress plays a critical effect on the durability of FRP, due to susceptibility of the bond between the fibers and resin matrices. In the present paper, molecular dynamics technique was used to model the moisture effect on the fiber-resin bond. The bonding performances of the epoxy on carbon fibers under dry and wet conditions were simulated. Free energy profiles were calculated to quantify interfacial adhesion. As shown from the decline of binding free energy, the water ingress led to remarkable deterioration of the fiber bonding to the resin matrix. The study is expected to be helpful for both the development of durable FRPs, and to predict the service life of a FRP subjected to hydrothermal aging accurately. Copyright © 2016 Department of Civil and Environmental Engineering & Research Institute for Sustainable Urban Development, The Hong Kong Polytechnic University.

关键词： Molecular dynamics

来源：评论

学校读者我要写书评

暂无评论

Bayesian system identification based on hierarchical sparse Bayesian learning and gibbs sampling with application to structural damage assessment

arXiv

引用

arXiv 2017年

作者： Huang, Yong Beck, James L. Li, Hui Key Lab of Structural Dynamic Behavior and Control of the Ministry of Education School of Civil Engineering Harbin Institute of Technology Harbin China Division of Engineering and Applied Science California Institute of Technology CA United States

Bayesian system identification has attracted substantial interest in recent years for inferring structural models based on measured dynamic response from a structural dynamical system. The focus in this paper is Bayesian system identification based on noisy incomplete modal data where we can impose spatially-sparse stiffness changes when updating a structural model. To this end, based on a similar hierarchical sparse Bayesian learning model from our previous work, we propose two Gibbs sampling algorithms. The algorithms differ in their strategies to deal with the posterior uncertainty of the equation-error precision parameter, but both sample from the conditional posterior probability density functions (PDFs) for the structural stiffness parameters and system modal parameters. The effective dimension for the Gibbs sampling is low because iterative sampling is done from only three conditional posterior PDFs that correspond to three parameter groups, along with sampling of the equation-error precision parameter from another conditional posterior PDF in one of the algorithms where it is not integrated out as a "nuisance" parameter. A nice feature from a computational perspective is that it is not necessary to solve a nonlinear eigenvalue problem of a structural model. The effectiveness and robustness of the proposed algorithms are illustrated by applying them to the IASE-ASCE Phase II simulated and experimental benchmark studies. The goal is to use incomplete modal data identified before and after possible damage to detect and assess spatially-sparse stiffness reductions induced by any damage. Our past and current focus on meeting challenges arising from Bayesian inference of structural stiffness serve to strengthen the capability of vibration-based structural system identification but our methods also have much broader applicability for inverse problems in science and technology where system matrices are to be inferred from noisy partial information about their eigenq

关键词： Probability density function

来源：评论

学校读者我要写书评

暂无评论

Influence of mineral admixtures on the rheological behavior of self-compacting concrete

引用

Jilin Daxue Xuebao (Gongxueban)/Journal of Jilin University (Engineering and Technology Edition) 2016年第2期46卷 439-444页

作者： Gao, Xiao-Jian Sun, Bo-Chao Ye, Huan Wang, Zi-Long Key Lab of Structures Dynamic Behavior and Control Ministry of Education Harbin Institute of Technology Harbin150090 China School of Civil Engineering Harbin Institute of Technology Harbin150090 China

In this paper, the influence of mineral admixtures on the rheological properties of fresh Self-Compacting Concrete (SCC) mixture was studied using a new type of concrete rheometer. The results show that both yield shear stress and plastic viscosity of the SCC mixture decrease as the content of fly ash in the mixture increases. As the content of Ground Granulated Blast Furnace Slag (GGBFS) increases, the thixotropy behavior of the SCC mixture becomes more obvious, and the yield stress decreases first and then increases. Both the yield stress and the thixotropy behavior of SCC mixture increase with the addition of limestone powder. For all the SCC mixtures with different mineral admixtures, as the storage time increases, the thixotropy behavior of fresh concrete is gradually weakened, the yield stress increases and the plastic viscosity decreases. © 2016, Editorial Board of Jilin University. All right reserved.

关键词： Fly ash

来源：评论

学校读者我要写书评

暂无评论

Damage Detection for SMC Benchmark Problem: A Subspace-Based Approach

Damage Detection for SMC Benchmark Problem: A Subspace-Based...

引用

作者： Zhou, Wensong Li, Shunlong Li, Hui Key Laboratory of Structures Dynamic Behavior and Control of the Ministry of Education Harbin Institute of Technology Harbin150090 China School of Transportation Science and Engineering Harbin Institute of Technology Harbin150090 China Key Laboratory of Advanced Material and Intelligent Control Technology on Transportation Safety Harbin Institute of Technology Harbin150090 China

A full-scale bridge benchmark problem was issued by the Center of Structural Monitoring and control at the Harbin Institute of Technology. The data used in this problem were collected by an in situ structural health monitoring system implemented into a full-scale cable-stayed bridge before and after the bridge was damaged, which is very rare in structural health monitoring field. This benchmark problem will help to verify and/or make comparison of the condition assessment and the damage detection methods, which are usually validated by numerical simulation and/or laboratory testing of small-scale structures with assumed deterioration models and artificial damage. With respect to damage detection of girder, one of the benchmark problems, using the monitored and field testing acceleration data, this paper describes a damage detection method, based on a residual generated from a subspace-based covariance-driven identification method, to detect the damage, and give relative quantitative damage indexes. This method was applied on both two parts of the given benchmark problem, and then detailed discussions and results on this problem are reported in this paper. © 2016 World Scientific Publishing Company.

关键词： Damage detection

来源：评论

学校读者我要写书评

暂无评论

Realization of the global yield mechanism of RC frame structures by redesigning the columns using column tree method

引用

Science china(Technological Sciences) 2015年第10期58卷 1627-1637页

作者： BAI JiuLin OU JinPing School of Civil Engineering Harbin Institute of Technology Key Lab of Structures Dynamic Behavior and Control (Harbin Institute of Technology) Ministry of Education

Global failure mechanism, i.e., the strong-column weak-beam mechanism, can provide higher total energy dissipation capacity with less ductility demand on components than other failure modes, and results in a more uniform story drift distribution and higher resistance to earthquake loads at the system level. However, the current code-based elastic design method cannot guarantee the global failure mechanism of frame structures under severe earthquakes. In this paper, a simple, but practical design procedure is proposed to ensure the global failure mechanism of reinforced concrete(RC) frame structures by redesigning the columns using the column tree method(CTM). CTM considers the yield limit state of all beams and column bases. The code-based design is firstly carried out to determine the section information of all beams and base columns. Then, the internal force demands applied on the column tree can be derived. Lastly, the column moments, shear forces and axial forces are determined according to the free-body diagram of CTM to finish the column redesign. Two RC frame structures with 6 and 12 stories are illustrated to verify the design procedure. The analytical results demonstrate the proposed approach can realize the global failure mechanism.

关键词： global failure mechanism column tree method （CTM） reinforced concrete frame structures failure mode plastic hinges

来源：评论

学校读者我要写书评

暂无评论

Experimental studies on behavior of fully grouted reinforced-concrete masonry shear walls

引用

Earthquake Engineering and Engineering Vibration 2015年第4期14卷 743-757页

作者： Zhao Yan Wang Fenglai Key Lab of Structures Dynamic Behavior and Control (Harbin Institute of Technology) Ministry of Education School of Civil Engineering Harbin Institute of Technology

An experimental study is conducted on fully grouted reinforced masonry shear walls (RMSWs) made from concrete blocks with a new configuration. Ten RMSWs are tested under reversed cyclic lateral load to investigate the influence of different reinforcements and applied axial stress values on their seismic behavior. The results show that flexural strength increases with the applied axial stress, and shear strength dominated by diagonal cracking increases with both the amount of horizontal reinforcement and applied axial stress. Yield displacement, ductility, and energy dissipation capability can be improved substantially by increasing the amount of horizontal reinforcement. The critical parameters for the walls are derived from the experiment: displacement ductility values corresponding to 15% strength degradation of the walls reach up to 2.6 and 4.5 in the shear and flexure failure modes, respectively; stiffness values of flexure- and shear-dominated walls rapidly degrade to 17%–19% and 48%–57% of initial stiffness at 0.50 D_max (displacement at peak load). The experiment suggests that RMSWs could be assigned a higher damping ratio (～14%) for collapse prevention design and a lower damping value (～7%) for a fully operational limit state or serviceability limit state.

关键词： reinforced-concrete masonry shear wall shear strength ductility stiffness degradation energy dissipation equivalent viscous damping ratio

来源：评论

学校读者我要写书评

暂无评论

Corrigendum to “Predicting water permeability and relative gas permeability of unsaturated cement-based material from hydraulic diffusivity” [Cem. Concr. Res. 58 (2014) 152–1 60]

引用

Cement and Concrete Research 2016年 87卷 105-106页

作者： Chunsheng Zhou Key Lab of Structures Dynamic Behavior and Control (Harbin Institute of Technology) Ministry of Education Heilongjiang Harbin 150090 China School of Civil Engineering Harbin Institute of Technology Harbin 150090 China

来源：评论

学校读者我要写书评

暂无评论

Damage detection in metallic plates using d36 piezoelectric phased arrays 8

Damage detection in metallic plates using d36 piezoelectric ...

引用

8th European Workshop on Structural Health Monitoring, EWSHM 2016

作者： Wang, Wentao Lynch, Jerome P. Li, Hui Key Lab of Structures Dynamic Behavior and Control Ministry of Education Harbin Institute of Technology Harbin150090 China Department of Civil and Environmental Engineering University of Michigan Ann ArborMI48109-2125 United States Department of Electrical Engineering and Computer Science University of Michigan Ann ArborMI48109-2125 United States

ISBN: (纸本)9781510827936

Recently, d36-type piezoelectric wafers derived from lead magnesium niobate-lead titanate (PMN-PT) single crystal materials have been proposed for elastic wave generation in thinwalled structures. In contrast to traditional d31 piezoelectric materials which generate symmetric and anti-symmetric Lamb waves, d36 introduces these same Lamb waves plus an inplane shear horizontal (SH) wave. Based on guided wave theory, the SH0 wave mode is nondispersive which may find many advantages uses in structural health monitoring. To detect and localize damage (e.g., cracks, corrosion) in thin walled structures, a phased array of d36- type piezoelectric wafers is proposed. To validate the proposed phase array, extensive experiments have been conducted using an aluminum plate with four d36 PMN-PT piezoelectric wafers surface bonded. The d36 phased array is shown capable of accurately detecting the location of local damage in the plate. Good detection accuracy is observed indicating that this proposed methodology has the potential to provide an effective identification of damage in metallic thin walled structures.

关键词： Damage detection

来源：评论

学校读者我要写书评

暂无评论

Creep of concrete with high amounts of supplementary cementitious materials and applications in concrete-filled tubes 4

Creep of concrete with high amounts of supplementary cementi...

引用

4th International Conference on Sustainable Construction Materials and Technologies, SCMT 2016

作者： Kuder, Katie Lehman, Dawn Chien, Jie Roeder, Charles Lowes, Laura Civil and Environmental Engineering Seattle University 901 12th Ave SeattleWA98122-1090 United States More Hall Civil and Environmental Engineering University of Washington SeattleWA98195-2700 United States Key Lab of Structures Dynamic Behavior Control of the Ministry of Education Harbin Institute of Technology Harbin150090 China

Due to its design versatility, availability and cost efficiency, concrete continues to play a dominant role in the construction industry. However, the production of Portland cement, a primary component of typical concrete mixes, is known to have a serious impact on the environment. Increasing the use of supplementary cementitious materials (SCMs) in concrete is an obvious and necessary step to reduce the carbon emissions associated with cement production. However, most reinforced concrete (including cast-in-place and precast) structural components rely on the early stiffness and strength of the concrete to resist self-weight and construction loadings after the release of the formwork. In contrast to cement-only concretes, high SCM concretes require more time to reach the target strength and stiffness values. Therefore, a structural component that does not depend on these engineering properties during construction is preferred. Concrete-filled tubes (CFTs) offer a solution to this challenge, with the steel tube is able to support construction loads while the high SCM concrete fill develops its strength and stiffness. However, there are concerns about the long-term deformations (creep) of high SCM concrete and its impact on CFT performance. This research develops models to predict the long-term (creep) response of SCM concretes and uses those predictive models to assess the long-term response of CFTs with SCM concrete fill. The models were validated using a large SCM database and two full-scale CFTs with SCM concrete fill that were tested under sustained loading. © 2016 International Committee of the SCMT conferences. All rights reserved.

关键词： Creep

来源：评论

学校读者我要写书评

暂无评论

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

请选择保存的检索档案：

请选择收藏分类：

通借通还

建议与咨询 留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

请选择保存的检索档案： 新增检索档案 确定 取消

请选择收藏分类： 新增自定义分类 确定 取消

通借通还

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

请选择保存的检索档案：

请选择收藏分类：