检索结果-内蒙古大学图书馆

Data Driven control and Learning systems (DDCLS)

作者： Yunge Zang Yan Li Yuting Duan Xiangyu Li Xi Chang Zhen Li Beijing Aerospace Automatic Control Institute Beijing P. R. China National Key Laboratory of Science and Technology on Aerospace Intelligence Control Beijing P. R. China Beijing Aerospace Institute for Metrology and Measurement Technology Beijing P. R. China Key Laboratory for Intelligent Control … Decision on Complex Systems School of Automation Beijing Institute of Technology Beijing China

To facilitate ground station monitoring and command uploading, unmanned aerial vehicles (UAVs) need to frequently exchange individual state data between units. However, this results in a significant usage of communication bandwidth. To address this issue, on the basis of an event-triggered strategy, this paper proposes an Extended Kalman Filter (EKF). aimed at reducing the communication burden of UAVs while maintaining high accuracy. Specifically, a state measurement triggered by an event is selected for filtering only if it contains innovation, thereby reducing the amount of data that needs to be communicated. Since UAV systems are nonlinear, EKF is adopted to fully utilize the information obtained from event-triggered strategies, thereby enhancing the estimation performance. In this paper, a physical UAV was used to verify the proposed algorithm, and it proved to have robust dynamic performance and to effectively reduce the communication rate.

关键词：

来源：评论

学校读者我要写书评

暂无评论

Parallel control for Optimal Tracking via Adaptive Dynamic Programming

引用

IEEE/CAA Journal of Automatica Sinica 2020年第6期7卷 1662-1674页

作者： Jingwei Lu Qinglai Wei Fei-Yue Wang School of Artificial Intelligence University of Chinese Academy of SciencesBeijing 100049 The State Key Laboratory for Management and Control of Complex Systems Institute of AutomationChinese Academy of SciencesBeijing 100190China IEEE State Key Laboratory for Management and Control of Complex Systems Institute of AutomationChinese Academy of SciencesBeijing 100190 Institute of Systems Engineering Macao University of Science and TechnologyMacao 999078 Qingdao Academy of Intelligent Industries Qingdao 266109China

This paper studies the problem of optimal parallel tracking control for continuous-time general nonlinear *** existing optimal state feedback control,the control input of the optimal parallel control is introduced into the feedback ***,due to the introduction of control input into the feedback system,the optimal state feedback control methods can not be applied *** address this problem,an augmented system and an augmented performance index function are proposed ***,the general nonlinear system is transformed into an affine nonlinear *** difference between the optimal parallel control and the optimal state feedback control is analyzed *** is proven that the optimal parallel control with the augmented performance index function can be seen as the suboptimal state feedback control with the traditional performance index ***,an adaptive dynamic programming(ADP)technique is utilized to implement the optimal parallel tracking control using a critic neural network(NN)to approximate the value function *** stability analysis of the closed-loop system is performed using the Lyapunov theory,and the tracking error and NN weights errors are uniformly ultimately bounded(UUB).Also,the optimal parallel controller guarantees the continuity of the control input under the circumstance that there are finite jump discontinuities in the reference ***,the effectiveness of the developed optimal parallel control method is verified in two cases.

关键词： Adaptive dynamic programming(ADP) nonlinear optimal control parallel controller parallel control theory parallel system tracking control neural network(NN)

来源：评论

学校读者我要写书评

暂无评论

Research on Attention-Based Predictive Model in Multi-Agent Reinforcement Learning

Research on Attention-Based Predictive Model in Multi-Agent ...

引用

2022 Chinese automation Congress, CAC 2022

作者： Hong, Weixin Wu, Huaiyu Shen, Zhen Xiong, Gang Hu, Bin Dong, Xisong Wang, Fei-Yue The State Key Laboratory for Management and Control of Complex Systems Institute of Automation Chinese Academy of Sciences Beijing100190 China School of Artificial Intelligence University of Chinese Academy of Sciences Beijing100049 China The Beijing Engineering Research Center of Intelligent Systems and Technology Institute of Automation Chinese Academy of Sciences Beijing100190 China The Guangdong Engineering Research Center of 3D Printing and Intelligent Manufacturing Cloud Computing Center Chinese Academy of Sciences Dongguan523808 China

ISBN: (纸本)9781665465335

Agent actions planning is a challenging problem in multi-agent reinforcement learning. Recent methods typically build their predictive models by full connection layers, but the shortage of utilizing action and observation information in complex multi-agent environment limits the performance of those methods. To address this issue, we propose a novel predictive model based on self-attention mechanism which can effectively use information in the environment. Specifically, we use the MADDPG algorithm to make a dataset where the input is the observations and actions and the output is the predicted observations and rewards. We also introduce the multi-head attention mechanism into the predictive model so that the predictive model can better combine different information for prediction. We perform extensive experiments to assess the proposed method and compare it with the representative baseline approach. Results demonstrate that our method outperforms competitors with higher accuracy in different tasks. Our implementation will be publicly available. © 2022 IEEE.

关键词： Reinforcement learning

来源：评论

学校读者我要写书评

暂无评论

Memristor-Based Circuit of Sequential Associative Memory with Memory Interactions and Stimulus Similarity Effect

引用

IEEE Transactions on Cognitive and Developmental systems 2025年

作者： Xiong, Dongdong Wang, Xiaoping Jiang, Yiming Yang, Chao Jiang, Man Lai, Jingang Zeng, Zhigang Huazhong University of Science and Technology School of Artificial Intelligence and Automation Wuhan430074 China Key Laboratory of Image Processing and Intelligent Control of Education Ministry of China Wuhan430074 China Hubei Key Laboratory of Braininspired Intelligent Systems Wuhan430074 China Huazhong University of Science and Technology Institute of Artificial Intelligence School of Artificial Intelligence and Automation Key Laboratory of Image Processing and Intelligent Control of Education Ministry of China Wuhan430074 China Guangxi University of Science and Technology School of Computer Science and Technology Liuzhou545006 China Huazhong University of Science and Technology Department of Physiology School of Basic Medicine and Tongji Medical College Wuhan430030 China

Most proposed memristor-based circuits of associative memory consider various mechanisms in only one associative memory. Few works on circuit design of sequential associative memory have been reported. In this paper, a memristor-based circuit of sequential associative memory with memory interactions and stimulus similarity effect is designed. Two associative memories, the prior associative memory (PAM) and the later associative memory (LAM), are formed successively. The PAM modifies the rate of the formation of the LAM, and the LAM, in turn, affects the strength of the PAM, which are two interactions in sequential associative memory, called transfer and retroaction. In addition, the magnitudes of transfer and retroaction are determined by the similarity of the conditioned stimuli. The above functions are realized by the ring input processing module, memory module, transfer module and retroaction module. It has been identified in circuit analysis that the proposed circuit is power efficient and has good robustness. Furthermore, the proposed circuit has promising applications for fire rescue robots. © 2016 IEEE.

关键词： Associative storage

来源：评论

学校读者我要写书评

暂无评论

Collaborative Scheduling of Computing Tasks for Edge Computing

Collaborative Scheduling of Computing Tasks for Edge Computi...

引用

2021 China automation Congress, CAC 2021

作者： Liu, Yue Xiong, Gang Zhu, Fenghua Chen, Shichao Zhang, Liguo Liu, Xudong School of Artificial Intelligence and Automation Beijing University of Technology The State Key Laboratory for Management and Control of Complex Systems Institute of Automation Chinese Academy of Sciences Beijing China Beijing Engineering Research Center of Intelligent Systems and Technology Institute of Automation The Cloud Computing Center Chinese Academy of Sciences Beijing China The State Key Laboratory for Management and Control of Complex Systems Institute of Automation Qingdao Academy of Intelligent Industries Chinese Academy of Sciences Beijing China Faculty of Information and Technology Beijing University of Technology Beijing China

ISBN: (纸本)9781665426473

In the face of the rapid development of the IoT, the traditional cloud computing, while providing services for mobile intelligent devices, also brings problems such as network bandwidth occupation and communication delay. Edge computing can solve these problems to some extent. But too many offloaded tasks may result in an edge server becoming overloaded and execution delay of tasks increasing, the computing resources of idle edge devices are also not fully utilized. In order to make full use of the computing resources of idle edge devices in the local network and reduce the execution delay for computing tasks, this paper takes the average delay time for all end devices as the optimization objective and proposes an end-edge cooperative scheduling (EECS) model to schedule tasks for edge computing. The scheduling algorithm used in EECS model is improved based on MCT algorithm. We use the EdgeCloudSim to verify the EECS model and scheduling algorithm. The simulation results show that the average completion time of computing tasks in EECS model, compared with only single edge server (SEE) task computing model, can be reduced by up to three times. In addition, the system load can be balanced to a certain extent in local network. © 2021 IEEE

关键词： Edge computing

来源：评论

学校读者我要写书评

暂无评论

Automated Assembly by Two-Fingered Microhand for Fabrication of Soft Magnetic Microrobots

Automated Assembly by Two-Fingered Microhand for Fabrication...

引用

IEEE International Conference on Robotics and automation (ICRA)

作者： Yue Zhao Xiaoming Liu Ruixi Wang Dan Liu Masaru Kojima Qiang Huang Tatsuo Arai Key Laboratory of Biomimetic Robots and Systems Ministry of Education State Key Laboratory of Intelligent Control and Decision of Complex System Beijing Advanced Innovation Center for Intelligent Robots and Systems Beijing China School of Mechatronical Engineering Beijing Institute of Technology Beijing China Department of Intelligent Manufacturing Shenzhen International Graduate School Tsinghua University Shenzhen China Department of Materials Engineering Science Osaka University Osaka Japan Center for Neuroscience and Biomedical Engineering The University of Electro-Communications Tokyo Japan

ISBN: (数字)9798350384574

ISBN: (纸本)9798350384581

Micro-assembly is an emerging method to fabricate microrobots with multiple modules or particles. However, there is always a lack of a flexible and efficient method to freely create the desired magnetic soft microrobots. In this paper, an automated assembly system based on a two-fingered microhand is presented for fabricating magnetic soft microrobots. Our proposed system can automatically pick and place components to assemble microrobots with a two-fingered micromanipulator, and orient these components through an external magnetic field. The automated assembly has the advantages of high accuracy, high speed, and high success rate. It can endow magnetic microrobots with flexible material selection, arbitrary geometry design, and programable magnetization profile. We can make full use of this system to fabricate multiple magnetic soft microrobots. The experiment results demonstrate that this system can efficiently fabricate microrobots with excellent mechanical properties, which have application potential in robotics, biomedical engineering, and environmental governance.

关键词： Three-dimensional displays Shape Micromanipulators Magnetization Manuals Three-dimensional printing Soft magnetic materials

来源：评论

学校读者我要写书评

暂无评论

Observer-Based Data-Driven Consensus control for Nonlinear Multiagent systems with Faded Neighborhood Information

SSRN

引用

SSRN 2022年

作者： Yin, Caiyun Ren, Hongru Li, Hongyi Lu, Renquan School of Automation The Guangdong Province Key Laboratory of Intelligent Decision and Cooperative Control Guangdong University of Technology Guangdong Guangzhou510006 China

A data-driven consensus control approach is proposed for unknown nonlinear multiagent systems (MASs) with faded neighborhood information and disturbance under Markov switching topologies. Since the exact model of MASs is unknown, each agent is given an equivalent affine data model using a local dynamic linearization method. To estimate the time-varying parameter in the affine data model, an adaptive update algorithm is designed. The total uncertainty induced by parameter estimation error and unknown nonlinearity is estimated using a discrete extended state observer and compensated in the control law. Further, considering the impact of the faded neighborhood information, a compensation term is introduced to correct the output information. Then, a data-driven consensus control protocol is proposed, and the convergence is proved by employing the contraction mapping principle. Finally, the simulation study tests the theoretical results. © 2022, The Authors. All rights reserved.

关键词： Multi agent systems

来源：评论

学校读者我要写书评

暂无评论

Prediction Method of Truck Travel Time in Open Pit Mines Based on LSTM Model

Prediction Method of Truck Travel Time in Open Pit Mines Bas...

引用

Chinese control Conference (CCC)

作者： Mengting Ao Changhe Li Shengxiang Yang School of Automation China University of Geosciences Wuhan China Hubei Key Laboratory of Advanced Control and Intelligent Automation for Complex Systems Wuhan China Engineering Research Center of Intelligent Technology for Geo-Exploration Ministry of Education Wuhan China School of Computer Science and Informatics De Montfort University Leicester United Kingdom

Aiming at the prediction of truck travel time in open pit mines, we established a prediction model based on long short-term memory(LSTM). This model fully accounts for 11 factors, including the nature of trucks, weather, road conditions, and driver's behaviors, as well as the influence of neighbor road segments in the route on the current predicted road segment. The experiment shows that the error of the LSTM prediction model is significantly reduced compared with SVR and BP models. In addition, the maximum absolute mean error under different conditions is less than 12 seconds.

关键词：

来源：评论

学校读者我要写书评

暂无评论

A Lightweight Object Detection Network for Industrial Robot Based YOLOv5

A Lightweight Object Detection Network for Industrial Robot ...

引用

Chinese automation Congress (CAC)

作者： Tao Zhong Yahui Gan Zao Han Huan Gao Ang Li Key Laboratory of Measurement and Control of Complex Systems of Engineering School of Automation Southeast University Ministry of Education NanJing China Nanjing YingQi Intelligent Technology Co. Ltd. Intel Joint Research Institute on Intelligent Edge Computing NanJing China

With the rapid development of deep learning, it has been widely applied in fields such as computer vision, natural language processing, and robotics. Despite the superior performance of deep learning in object detection, most industrial vision robots still rely on traditional object detection methods due to computational constraints of robot controllers. In order to improve the performance of object detection for vision robots, a lightweight 3D object detection network based on You Only Look Once version 5 (YOLOv5) is proposed for satisfying industrial production. YOLOv5 work to efficiently object detection using deep convolutional networks. In terms of model deployment, we adopt a novel OpenVINO-based model deployment approach. The OpenVINO framework significantly enhances the inference speed of models by model optimization and compression. Our model achieves a 70% reduction in inference time compared to the baseline model on CPU. The effectiveness of the proposed method is demonstrated through experiments.

关键词：

来源：评论

学校读者我要写书评

暂无评论

Real-time In-situ Defect Detection in 3D Printing of Continuous Fiber-Reinforced Composites

Real-time In-situ Defect Detection in 3D Printing of Continu...

引用

Digital Twins and Parallel Intelligence (DTPI), IEEE International Conference on

作者： Zhijian Yue Zhen Shen Xiangyang Dong Qihang Fang Weixing Wang Xisong Dong Gang Xiong Fei-Yue Wang School of Artificial Intelligence University of Chinese Academy of Sciences Beijing China State Key Laboratory of Multimodal Artificial Intelligence Systems Beijing Engineering Research Center of Intelligent Systems and Technology Institute of Automation Chinese Academy of Sciences Beijing China Intelligent Manufacturing Center Qingdao Academy of Intelligent Industries Qingdao China Guangdong Engineering Research Center of 3D Printing and Intelligent Manufacturing Cloud Computing Center Chinese Academy of Sciences Dongguan China State Key Laboratory for Management and Control for Complex Systems Institute of Automation Chinese Academy of Sciences Beijing China

ISBN: (数字)9798350349252

ISBN: (纸本)9798350349269

With the development of continuous fiber-reinforced composites (CFRCs) 3D printing technology, timely, efficient and accurate detection of fiber path defects is essential for ensuring product quality and performance. However, challenges still need to be addressed in this field, such as inadequate training data coverage and the complexity of fiber path structures. These factors hinder the capability of traditional methods to accurately assess the status of printed products. Therefore, developing accurate and robust fiber path defect detection techniques is crucial for CFRCs 3D printing technology. In this paper, we propose a precise detection method for fiber path defects in CFRCs 3D printing using the YOLOv7 object detection model combined with a Squeeze-and-Excitation (SE) attention mechanism. By introducing the SE attention mechanism, we enhance the perception capability of the YOLOv7 model for crucial features, thereby improving the accuracy of fiber path defect detection. The experimental results show that the YOLOv7 model, when augmented with an attention mechanism, achieves an average accuracy of 93.9% in identifying fiber path defects during the printing process. Compared to models without this attention mechanism, the results show that there is 10.7% increase, with a notably enhanced learning capacity during the training phase, which substantiates the efficacy and practicality of the proposed approach.

关键词： Training Solid modeling Accuracy Attention mechanisms Training data Three-dimensional printing Real-time systems Quality assessment Optical fiber testing Defect detection

来源：评论

学校读者我要写书评

暂无评论

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

请选择保存的检索档案：

请选择收藏分类：

通借通还

建议与咨询 留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

请选择保存的检索档案： 新增检索档案 确定 取消

请选择收藏分类： 新增自定义分类 确定 取消

通借通还

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

请选择保存的检索档案：

请选择收藏分类：