检索结果-内蒙古大学图书馆

18th International Topical Meeting on Nuclear Reactor Thermal Hydraulics, NURETH 2019

作者： Wang, Kailin Li, Liangxing Xie, Wei Zhang, Shuangbao State Key Laboratory of Multiphase Flow in Power Engineering Xi'an Jiaotong University Xianning West Road 28# Xi’an city710049 China

The hydraulic performance of lead-bismuth eutectic (LBE) pump is of great importance for the safety aspects concerning lead-alloy cooled fast reactors (LFRs). To investigate the effect of different rotation speed on the performance of axial LBE pump, different rotation speed axial LBE pumps are designed by planar cascade and streamline method with the same mass flow rate and hydraulic head. Ansys BladeGen is used to establish the three-dimensional model of the axial-flow pump. CFD software (Ansys CFX) carry out numerical calculation. Numerical studies are used to compared the performance between two pumps with different rotation speed. To improve the accuracy of CFD simulation, the numerical result is verified by grid independence method and compared with theoretical calculation result. The flow velocity of the liquid LBE have great impact on the design of LBE pump because of the requirement to avoid affect of corrosion. It is found that the maximum flow velocity of low rotation speed pump is about 7.8 m/s, which is lower than the maximum flow velocity of high rotation speed pump in the case of constant volume and performance. Performance of low rotation speed pump meets the requirements of the reactor operating under long-term high load. The research results could be a viable solution used as a reference for the development of LFRs. © 2019 American Nuclear Society. All rights reserved.

关键词： Pumps

来源：评论

学校读者我要写书评

暂无评论

Laminar burning velocity of gasoline and gasoline surrogates under various pressures and temperatures 12

Laminar burning velocity of gasoline and gasoline surrogates...

引用

12th Asia-Pacific Conference on Combustion, ASPACC 2019

作者： Hu, Erjiang Xu, Zhaohua Gao, Zhenhua Huang, Zuohua Stake Key Laboratory of Multiphase Flow in Power Engineering Xi'an Jiaotong University No.28 Xianning West Road Shaan Xi710049 China

The outwardly propagating spherical flame method was used to measure the laminar burning velocity of a commercial gasoline fuel having RON of 92 and gasoline surrogate. Measurements were conducted at the equivalence ratio of 0.8 to 1.5, initial temperatures of 358 K, 403 K, and 448 K and initial pressures of 1 atm, 2 atm and 5atm in a constant volume bomb. The surrogate of primary reference fuel (PRF-92, 92% iso-octane + 8% n-heptane) and toluene reference fuel (TRF-92, 16.69% iso-octane + 22.65% n-heptane + 60.66% toluene) were proposed to match the laminar burning velocity of gasoline (CNPC 92#). It could be found that the TRF-92 was able to successfully reproduce the laminar burning velocity of the gasoline under various experimental conditions. © Asia-Pacific Conference on Combustion, ASPACC *** right reserved.

关键词： Gasoline

来源：评论

学校读者我要写书评

暂无评论

Thermal Simulation for a Mechanical Spindle With External Cooler Across Grease Coated Interface

Research Square

引用

Research Square 2021年

作者： Zhao, Liang Lei, Mohan Ren, Hongdi Wang, Jinshi Wang, Shuai Li, Ben Q. Yang, Jun Mei, Xuesong Xi'an Jiaotong University China State Key Laboratory for Manufacturing Systems Engineering Xi'an Jiaotong University Xi'An710049 China Shaanxi Key Laboratory of Intelligent Robots Xi'an Jiaotong University Xi'An710049 China School of Mechanical and Precision Instrument Engineering Xi'an University of Technology 710048 China State Key Laboratory of Multiphase Flow in Power Engineering Xi’an Jiaotong University Xi’an710049 China Department of Mechanical Engineering College of Engineering and Computer Science University of Michigan MI48128 United States

Spindles in precision boring machine often work in low speed and heavy load without internal cooling, and the thermal error is nonnegligible. So an external cooling system was designed, and the effectiveness of the designed scheme needs to be preliminarily verified by simulation before building the cooling system. Thermal simulations of the spindle with an external cooler require calculating the thermal resistance of the thermal grease-coated interface between the cooler and spindle. Models describing the contact thermal resistance and total thermal resistance for metal contact filled with silicone grease based on solid-liquid interface force equivalence were described in this paper, and experiments were also conducted to verify the accuracy of these models. The contact thermal resistances between the cast iron/copper and silicone grease on flat or arc surfaces were calculated, and the bulk thermal resistance of the silicone grease layer was calculated. The total heat transferred between the cooler and the silicone grease-coated interface of the spindle were calculated. Heat transfer and heat generation in the spindle were calculated, and a finite element model was established to verify the effectiveness of the designed external cooling scheme. Finally, results from experiments for the spindle in different conditions show that the external cooling system decreases the time to reach thermal equilibrium by more than 60%. The RMSE of the simulated thermal elongation is less than 5.7044 μm when the rotating speed of 3000 rpm, and is less than 3.9714 μm when the rotating speed is 1500 rpm. © 2021, CC BY.

关键词： Cooling

来源：评论

学校读者我要写书评

暂无评论

Review on development of carbon nanotube field emission cathode for space propulsion systems

引用

High Voltage 2020年第4期5卷 409-415页

作者： Chao Huo Feng Liang An-bang Sun Science and Technology on Combustion Internal Flow and Thermal-structure LaboratorySchool of AstronauticsNorthwestern Polytechnical UniversityXi'anShaanxiPeople's Republic of China Faculty of Metallurgical and Energy Engineering Kunming University of Science and TechnologyKunmingPeople's Republic of China State Key Laboratory of Electrical Insulation and Power Equipment School of Electrical EngineeringXi'an Jiaotong UniversityXi'an 710049People's Republic of China

In recent years,small-size,low-weight aerospace propulsion systems have developed rapidly for space exploration,on-orbit scientific instruments and extra space missions,while additional electron emission devices are commonly required in those propulsion *** nanotube(CNT)based field emission cathodes exhibit extraordinary field emission properties and are regarded to be an ideal alternative of conventional thermionic or hollow *** this study,the authors give an overview of present status of researches on CNT-based electron emission cathodes for utilising as neutralisers or electron sources particularly in space electric propulsion systems,the theory and characteristics of CNT are also ***,challenges,problems and possible solutions before actual applications of CNT in a space mission are discussed accordingly.

关键词： field neutral emission

来源：评论

学校读者我要写书评

暂无评论

Modulating conductivity type of cuprous oxide（Cu2O） films on copper foil in aqueous solution by comproportionation

引用

Journal of Materials Science & Technology 2019年第8期35卷 1570-1577页

作者： Changwei Tang Xiaohui Ning Jian Li Hui-Lin Guo Ying Yang Shaanxi Provincial Key Laboratory of Electroanalytical Chemistry Key Laboratory of Synthetic and Natural Functional Molecule Chemistry of the Ministry of EducationCollege of Chemistry & Materials ScienceNorthwest UniversityXi'an 710127 China National Demonstration Center for Experimental Chemistry Education Northwest UniversityXi'an 710127 China International Research Center for Renewable Energy State Key Laboratory of Multiphase Flow in Power EngineeringXi'an Jiaotong UniversityXi'an 710049 China

Cuprous oxide(Cu2O)is an attractive material for photoelectrochemical(PEC)hydrogen production or photovoltaic application,because of its appropriate band gap,low material cost and *** this paper,Cu2O films were obtained by comproportionation in acid cupric sulfate solutions with varying concentrations of potassium *** and electrochemical experiments,such as zero-bias photocurrent responses,voltammograms,and Mott-Schottky measurements,show that the Cu2O films grown in low(≤0.75 mol dm^–3)and high(≥1.00 mol dm^–3)nitrate ion concentrations presented n-type and p-type conductivity,*** circuit potential and polarization behavior were monitored to investigate the mechanism of modulating conductivity *** ions consume protons in the plating solution during comproportionation with different concentrations of nitrate ions creating different pH at the Cu2O/solution *** gradient leads to the transformation of Cu2Ofilms conductivity changing from n-type to p-type with increasing the concentration of nitrate ions in the plating *** method could be used to fabricate homojunction electrode on metal substrate for PEC hydrogen production or photoelectric application.

关键词： Cuprous oxide(Cu2O) Comproportionation Semiconductor films Tuning conductivity Photoelectrochemical cell

来源：评论

学校读者我要写书评

暂无评论

Wake of a stationary sphere near a wall

引用

Huagong Xuebao/CIESC Journal 2019年第9期70卷 3300-3306页

作者： Li, Xing Bai, Bofeng State Key Laboratory of Multiphase Flow in Power Engineering Xi'an Jiaotong University Xi'anShaanxi710049 China

The flow characteristics of the sphere under uniform flow in a large space have been extensively studied, but the influence of the wall on the flow characteristics of the sphere is not clear. The wake of the particle is focused. Results show that there are three regimes of the sphere wake, which are steady wake, unsteady symmetric wake and unsteady asymmetric wake. If Re400, the vortex shedding is not symmetric and becomes chaotic as Reynolds number increases. © All Right Reserved.

关键词： Wakes

来源：评论

学校读者我要写书评

暂无评论

Experimental and numerical study on impinging fuel spray under high-pressure cross-flow condition 14

Experimental and numerical study on impinging fuel spray und...

引用

14th International Conference on Liquid Atomization and Spray Systems, ICLASS 2018

作者： Si, Z. Guo, M. Ashida, Y. Nishida, K. Ogata, Y. Tang, C. Huang, Z. Department of Mechanical System Engineering University of Hiroshima 1-4-1 Kagamiyama Higashi-Hiroshima739-8527 Japan School of Mechanical and Electronic Engineering Wuhan University of Technology 122 Luoshi road Wuhan Hubei430070 China State Key Laboratory of Multiphase Flow in Power Engineering Xi'an Jiaotong University 28 Xianning west road Xi'an710049 China

It is certified that the fuel spray is strongly affected by both in-cylinder air flow and piston cavity wall impingement in a direct injection engine. In this study, sprays injected by a valve covered orifice nozzle were tested by a high-speed video camera and a continuous wave laser sheet under a wind-tunnel with cross-flow and pressurized ambience, thereby the spray profiles in vertical and horizontal planes were investigated. Moreover, the experiment results were compared with simulations which was calculated by the validated spray models based on the CONVERGE software. With increase in the cross-flow velocity, the spray tip penetration evidently increased, and the increased cross-flow velocity led to an increase in the vortex height because of the enhanced spray dispersion. Furthermore, the high ambient pressure restrains the spray dispersion and leads to smaller spray tip penetration and vortex height. The outlines of spray with same liquid-to-air momentum flux ratio q can agree with each other in the windward side, nevertheless the droplet diffusion under high cross-flow velocity is distinct in the leeside. At the horizontal plane of y=25mm, a complex vortex movement was observed that resulted in a nonuniform distribution of droplets in the upper part of the spray in the leeward side. From the calculations, in the radial region apart from the impingement point (8mm4mm) hardly moved. © 2018 Solar Turbines Incorporated.

关键词： Continuous wave lasers

来源：评论

学校读者我要写书评

暂无评论

Performance of cone meter for measuring cryogenic fluid considering cavitation

引用

International Journal of Fluid Machinery and Systems 2019年第1期12卷 12-21页

作者： He, Denghui Chang, Zhuang Bai, Bofeng Chen, Senlin Guo, Pengcheng State Key Laboratory of Eco-hydraulic in Northwest Arid Region Xi’an University of Technology NO.5 South Jinhua Road Xi’an710048 China State Key Laboratory of Multiphase Flow in Power Engineering Xi’an Jiaotong University No.28 Xianning West Road Xi’an710049 China

The performance of the cone meter when measuring the cryogenic fluid was investigated by numerical simulation. The results show that the discharge coefficient and pressure loss coefficient of the cone meter are almost constant when the Reynolds number in the "stable region". The cryogenic fluids, especially the liquid hydrogen, have wider stable Reynolds number ranges than the water. There is little effect of cavitation on the discharge coefficient and pressure loss coefficient at the initial stage of cavitation. Thus the effect of slight cavitation on the measurement error of the flow rate is small, whose relative error is less than ±0.5% in present cases. This study opens a new avenue for measuring the flow rate of the cryogenic fluid. © 2019, Turbomachinery Society of Japan. All rights reserved.

关键词： Cavitation

来源：评论

学校读者我要写书评

暂无评论

An optimal design of the widths of heat affect zone, fusion zone, and near interface zone in a dissimilar metal welded joint

Material Design and Processing Communications

引用

Material Design and Processing Communications 2020年第5期2卷

作者： Guo, Guoliang Yang, Jie Wang, Lei Liu, Guiqiu Zhang, Baozhong Zhang, Sihan Shanghai Key Laboratory of Multiphase Flow and Heat Transfer in Power Engineering School of Energy and Power Engineering University of Shanghai for Science and Technology Shanghai China Consumer Appliances Centre Shandong Product Quality Inspection Research Institute Shandong China

The optimal design of the dissimilar metal welded joint is a valuable research issue, whether optimize the material, processing technology, dimension, or anything else. The fracture behavior of the dissimilar metal welded joint have been found affected by the widths of heat affect zone, fusion zone, and near interface zone. In this study, the optimal design of the widths of heat affect zone, fusion zone, and near interface zone in the dissimilar metal welded joint was further studied systematically. Firstly, a dissimilar metal welded joint, which used in the nuclear power plants with either heat affect zone crack or fusion zone crack, was selected, and a width mismatch coefficient MW was defined. In addition, the crack propagation paths and J-resistance curves of the dissimilar metal welded joints under different MW induced by the widths of heat affect zone, fusion zone, and near interface zone were calculated. Based on the obtained results, the widths of heat affect zone, fusion zone, and near interface zone were optimized. This study will provide support for the design of the dissimilar metal welded joint and is significant to the structure integrity assessment of the nuclear power plants. © 2019 John Wiley & Sons, Ltd.

关键词： Nuclear fuels

来源：评论

学校读者我要写书评

暂无评论

Lithium Extraction from High Magnesium Salt Lake Brine with an Integrated Membrane Technology

SSRN

引用

SSRN 2022年

作者： Ashraf, Muhammad Awais Usman, Muhammad Hussain, Iftikhar Ahmad, Faraz Guo, Shiwei Zhang, Lu State Key Laboratory of Multiphase Complex Systems CAS Key Laboratory of Green Process and Engineering Institute of Process Engineering Chinese Academy of Sciences Beijing100190 PR China University of Chinese Academy of Sciences Beijing100049 China Washington State University United States Department of Mechanical Engineering City University of Hong Kong 83 Tat Chee Avenue Kowloon Hong Kong Key Laboratory of Coal Science and Technology Taiyuan University of Technology Taiyuan030024 China North China Electric Power University Hebei Key Lab of Power Plant Flue Gas Multi-Pollutants Control Department of Environmental Science and Engineering Baoding071000 China Faculty of Economics and Business

Lithium extraction is a great challenge from the high magnesium content salt solution. In this work, an integrated polyamide tight ultrafiltration (UF) and nanofiltration (NF) membranes are systematically investigated to separate Li+ from a high magnesium salt solution. Tight ultrafiltration UA001 and nanofiltration NF270 membranes in the integrated-cascade system not only increased Li+ permeation to 82.5% but also enhanced the high Mg2+ retention to 94.6% from the ternary salt solution of LiCl and MgCl2. The transport model was also developed to calculate the real retention of Li+ and Mg2+, under constant pressure mode. The separation efficiency SFLi/Mg for the ternary salt solution of LiCl+MgCl2+H2O was more than 15 at a constant pressure of 25 bars with an integrated membrane process, which was higher as compared to single-stage UF and NF270 membranes. Moreover, the high Mg2+/Li+ ratio was also reduced from 30 to 1.9 in the integrated-cascade membrane process. © 2022, The Authors. All rights reserved.

关键词： Magnesium compounds

来源：评论

学校读者我要写书评

暂无评论

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

请选择保存的检索档案：

请选择收藏分类：

通借通还

建议与咨询 留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

请选择保存的检索档案： 新增检索档案 确定 取消

请选择收藏分类： 新增自定义分类 确定 取消

通借通还

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

请选择保存的检索档案：

请选择收藏分类：