检索结果-内蒙古大学图书馆

2024 31st International Conference on Nuclear Engineering, ICONE 2024

作者： Yugao, Ma Jiahao, Lu Yue, Liu Suyi, Zhang Muhao, Zhang Science and Technology on Reactor System Design Technology Laboratory Nuclear Power Institute of China Chengdu610213 China College of Nuclear Technology and Automation Engineering Chengdu University of Technology Chengdu610059 China

ISBN: (纸本)9780791888247

The Fission Surface Power system is a feasible solution for future lunar surface exploration energy supply, with the solid-state reactor being considered a primary candidate. This paper presents a modeling and analysis of a solid-state reactor based on publicly available information. Using the reactor Monte Carlo program RMC and the commercial finite element analysis software ANSYS, the reactor is modeled and analyzed. The power distribution of the active zone and reactivity feedback coefficients of the entire core are obtained. The result indicates a negative reactivity feedback coefficient, confirming this reactor design's inherent safety. Furthermore, a two-dimensional reactor model is constructed to obtain the temperature distribution during full-power operation, and non-passive residual heat removal analysis and radiative heat loss failure analysis are performed. At the failure condition of all heat pipes, the maximum core temperature is 742 K, which is below the reactor safety temperature limit, confirming the residual heat removal capability of the solid-state reactor in the loss of heat sink. Additionally, the self-developed transient reactor system analysis program is used for thermal safety analysis. The thermal parameters and heat transfer limits of high-temperature alkali metal heat pipes within the reactor are obtained, with the ratio of heat transfer limit to the heat load of 2.05 demonstrating sufficient safety margins of the heat pipe operation in the reactor. The results manifest that the core is satisfied with the existing criteria for anticipated operating occurrences of solid-state reactors, verifying the excellent safety performance of this reactor design. Based on the analysis and calculations in this study, it is concluded that this reactor design exhibits superior safety performance, which is attributed to the neutron physics design concept of the intermediate neutron spectrum and the thermal-hydraulic design concept of non-passive residual h

关键词： Lunar surface analysis

来源：评论

学校读者我要写书评

暂无评论

Fault Severity Classification based on Information Flow and Support Vector Machines 8

Fault Severity Classification based on Information Flow and ...

引用

8th International Conference on Energy system, Electricity, and Power, ESEP 2023

作者： Yang, Xiaohua Liu, Zhikun Fang, Weiyang Huang, Tao Liu, Jie Yang, Jinghua Ren, Changan Department of Compute Science University of South China Hengyang421001 China Science and Technology on Reactor System Design Technology Laboratory Nuclear Power Institute of China Chengdu610041 China

ISBN: (数字)9781510679801

ISBN: (纸本)9781510679795

Fault severity describes the level of impact caused by a fault. In the event of a malfunction in a nuclear power plant, a vast amount of data and alarms are generated, making it challenging for operators to identify and determine the state of the power plant in a short time. If the fault severity can be effectively identified during a malfunction, it would allow the operators to respond quickly and prevent further losses. Compared to other machine learning methods, the Support Vector Machine (SVM) has superior classification capability in scenarios with limited nuclear power samples. However, if the feature representation of the SVM training sample is inadequate, resulting in similar, indistinguishable training data, it will affect the SVM's classification of fault severity. To address this issue, using the Liang-Kleeman Information Flow (IF) can characterize information transmission from a causal perspective. By introducing IF to combine features of the training data, insufficient sample features can be replaced with the IF that describes information from a causal viewpoint, thereby enhancing the SVM's accuracy in fault severity classification. This paper takes the Main Steam Line Break accident in the primary loop of the nuclear reactor as an example and conducts simulation experiments on the PCTRAN simulation platform. The experimental results show that under 5 different fault degrees, the accuracy of fault degree evaluation of SVM model combined with IF is improved. This method can effectively improve the classification accuracy of different fault severity degrees in MSLB steam flow data with similar changes. © 2024 SPIE.

关键词： Steam piping systems

来源：评论

学校读者我要写书评

暂无评论

Improving the ductility of laser directed energy deposited borated stainless steel by increasing laser power

引用

Journal of Manufacturing Processes 2025年 145卷 494-507页

作者： Huang, Sheng Li, Qingyu Zhang, Xiaoyu Cui, Bin Li, Dichen Zhang, Anfeng Miao, Kai State Key Laboratory for Manufacturing Systems Engineering School of Mechanical Engineering Xi'an Jiaotong University Xi'an710049 China Science and Technology on Reactor System Design Technology Laboratory Nuclear Power Institute of China Chengdu610213 China Department of Mechanical and Electrical Engineering Yuncheng University Yuncheng044000 China Co. Ltd. Chengdu610091 China

Borated stainless steels (BSSs) are extensively applied in the nuclear energy industry due to boron's excellent thermal neutron absorption capacity, but large and brittle borides formed during casting result in a low ductility. Here, a BSS was produced by laser directed energy deposition, and an investigation was conducted to analyze the impact of laser power on both the microstructure and mechanical properties of the deposited material. Fibrous borides with relatively low volume fraction in the overlapping zone resulted in higher ductility, while lamellar borides with relatively large volume fraction in the non-overlapping zone led to higher strength. As the laser power increased from 180 W to 330 W, the size of fibrous and lamellar eutectic borides and austenite increased significantly, the width of the soft overlapping zone increased by 2.27 times, and the elongation increased by 2.03 times, although yield strength and ultimate tensile strength decreased by 46.3 % and 31.7 %, respectively. As a result, these findings confirmed the feasibility of significantly improving the ductility of the as-deposited BSS by increasing the laser power. The work here provides a way to tailoring the mechanical properties of BSS produced by laser additive manufacturing. © 2025 The Society of Manufacturing Engineers

关键词： Ductility

来源：评论

学校读者我要写书评

暂无评论

Experimental Study on Startup Characteristics of Sodium Heat Pipe with Large Length-diameter Ratio 12

Experimental Study on Startup Characteristics of Sodium Heat...

引用

12th Academic Conference of Geology Resource Management and Sustainable Development, GRMSD 2024

作者： Li, Wenjun Zhang, Zhuohua Su, Dongchuan Wu, Ge Tang, Qizhong Wu, Junjie College of Chemical Safety North China Institute of Science and Technology Hebei Sanhe065201 China Key Laboratory of Nuclear Reactor System Design Technology Nuclear Power Research and Design Institute of China Sichuan Chengdu610213 China

ISBN: (纸本)9798331314545

Underground in-situ pyrolysis of oil-rich coal can extract oil and gas resources in coal, which is an important measure for clean and low-carbon utilization of coal resources. The efficiency and energy consumption of underground in-situ pyrolysis of oil-rich coal depend on the heating equipment. The sodium heat pipe with large length-diameter ratio can complete the efficient long-distance heat transfer at high temperature, and has broad application prospects in the field of underground in-situ pyrolysis of oil-rich coal. Compared with the conventional high temperature heat pipe, the evaporation section of the sodium heat pipe with large length-diameter ratio is more likely to burn out during cold start-up, which leads to the failure of cold start-up. Therefore, for the sodium heat pipe with an aspect ratio of 115 (outer diameter D = 20 mm, axial length L = 2300 mm), the start-up characteristics of sodium heat pipes with three filling rates (5 %, 10 %, 15 %) under different heating powers were investigated. The results show that with the increase of the filling rate, the longer the start-up time of the sodium heat pipe with large length-diameter ratio, the more likely it is to produce temperature oscillation. Increasing the heating power can reduce the start-up time gap of the three liquid-filled sodium heat pipes, weaken the temperature oscillation phenomenon, and improve the temperature uniformity and steady-state operating temperature of the sodium heat pipe with large length-diameter ratio. In addition, the decrease of the filling rate of sodium with large length-diameter ratio and the increase of heating power can reduce the equivalent thermal resistance of sodium heat pipe with large length-diameter ratio, and improve the start-up characteristics and heat transfer effect of sodium heat pipe with large length-diameter ratio. When the heating power is 3.5 kW, the start-up time of sodium heat pipe with 5 % filling rate is as low as 450 s. © 2024 Proceedings of the

关键词： Coal deposits

来源：评论

学校读者我要写书评

暂无评论

THE STUDY of COUPLED FUEL PERFORMANCE ANALYSIS and NEUTRONICS with COMSOL and RMC 29

THE STUDY of COUPLED FUEL PERFORMANCE ANALYSIS and NEUTRONIC...

引用

2022 29th International Conference on Nuclear Engineering, ICONE 2022

作者： Liu, Zhenhai Qi, Feipeng Zhou, Yi Li, Quan Chen, Ping Chen, Hao Ma, Chao Zhao, Bo Li, Chenxi Science and Technology on Reactor System Design Technology Laboratory Npic Chengdu China

ISBN: (纸本)9780791886366

Predicting fuel behavior in the reactor is a typical multiphysics coupling problem. The traditional fuel performance analysis adopts a decoupling way. To provide a higher fidelity tool for fuel performance simulation, the multi-physics coupling software COMSOL and 3D Monte Carlo neutron transport code RMC are coupled. The fuel rod thermo-mechanical coupling analysis module is constructed in COMSOL. RMC is innovatively wrapped as a component of COMSOL to communicate with the fuel performance module. Grid mapping algorithm is set up using COMSOL's functionality. A carefully designed segregation solver sequence is used to control the coupling process. The fine power distribution calculated by RMC is transferred to COMSOL fuel thermal calculation, and the fuel temperature and the coolant temperature and density calculated by COMSOL are transferred to RMC. In a Picard iterative way, the fuel rod lattice level neutron thermomechanical tight coupling is realized. The coupling is demonstrated in a fuel rod BOL steady state case. The fuel performance analysis is enhanced by the higher fidelity neutron flux solution. © 2022 American Society of Mechanical Engineers (ASME). All rights reserved.

关键词： Iterative methods

来源：评论

学校读者我要写书评

暂无评论

Emergent antisymmetric wrinkling patterns in films on ridged substrates

引用

science China(Physics,Mechanics & Astronomy) 2023年第11期66卷 179-187页

作者： Jiahui Zhang Yi Sun Linghui He Yong Ni CAS Key Laboratory of Mechanical Behavior and Design of Materials Department of Modern MechanicsCAS Center for Excellence in Complex System MechanicsUniversity of Science and Technology of ChinaHefei230026China

We report the formation of antisymmetric wrinkling patterns in films on ridged substrates induced by the buckling instability of the substrates via finite element simulations and *** simulated results reveal that the uniaxial compression along the ridge can trigger both the wrinkling instability of the film and the lateral buckling instability of the *** latter could change the wrinkles from a symmetric pattern to an antisymmetric pattern in a range of film-substrate modulus ratio and aspect ratio of the ridge profile,as validated by the experimental observations.A three-dimensional phase diagram with four buckling patterns,i.e.,sole ridge buckling pattern,antisymmetric wrinkling pattern with different wavelengths from ridge buckling,symmetric wrinkling pattern without ridge buckling,and antisymmetric wrinkling pattern with the same wavelength as ridge buckling,is built with respect to the uniaxial compression,modulus ratio,and aspect *** results not only elucidate how and when the interplay between the wrinkling instability and the ridge instability results in the formation of the antisymmetric wrinkling pattern but also offer a way to generate controllable complex wrinkling patterns.

关键词： wrinkling pattern buckling instability ridged film-substrate system antisymmetric wrinkles

来源：评论

学校读者我要写书评

暂无评论

REVIEW OF RISK-INFORMED SAFETY design CONCEPT, METHOD AND APPLICATION 30

REVIEW OF RISK-INFORMED SAFETY DESIGN CONCEPT, METHOD AND AP...

引用

30th International Conference on Nuclear Engineering, ICONE 2023

作者： Gong, Lanxin Zhong, Mingjun Peng, Changhong School of Nuclear Science and Technology University of Science and Technology of China Hefei China Science and Technology on Reactor System Design Technology Laboratory Nuclear Power Institute of China Chengdu China

ISBN: (纸本)9784888982566

Since the NRC issued the PSA policy in 1995, PSA containing risk information has been widely used in supervision and design. Subsequently, the concept of "risk-informed" has gained more and more recognition, and its application has expanded from the initial equipment maintenance to the current design. By analyzing the regulations, standards and other guidance documents of various countries and institutions on safety design, we reviewed the history of risk-informed safety design concepts, methods and their applications, especially the progress of LMP projects in the United States in recent years. We put forward prospects for the development and application of risk-informed concepts and methods in new reactors in the future. © 2023 by JSME.

关键词： design

来源：评论

学校读者我要写书评

暂无评论

A Transformer-based Time Series Prediction Model with Contrastive Learning for Nuclear Power system State Monitoring 15

A Transformer-based Time Series Prediction Model with Contra...

引用

15th IEEE Global Reliability and Prognostics and Health Management Conference, PHM-Beijing 2024

作者： Gou, Pengfei Zheng, Daiwei Tang, Lei Liu, Mengjuan School of Information and Software Engineering University of Electronic Science and Technology of China UESTC Chengdu China Science and Technology on Reactor System Design Technology Laboratory Nuclear Power Institute of China NPIC Chengdu China

ISBN: (纸本)9798350354010

Prognostics and Health Management (PHM) is currently the mainstream solution for the condition monitoring and maintenance of industrial systems. In PHM, the system condition is monitored by monitoring the operational status parameters of the system to diagnose equipment faults, predict the remaining useful life, etc. Utilizing sequential operational status parameters to complete prediction and classification tasks is usually modeled as a time series processing task. Therefore, a high-performance time series prediction model is crucial for PHM. This paper focuses on the use of time series prediction models to achieve the prediction of key state parameters of the nuclear power system. However, there are still some challenges when directly applying existing time series prediction models to industrial systems. First, obtaining operational data on the nuclear power system is relatively difficult, resulting in a small amount of training data, which causes many models to face the risk of insufficient training or overfitting. Second, most of the existing time series prediction models are composed of high- and low-frequency decoupling modules, while the operational data of nuclear power systems often have fewer high-frequency components, making it difficult for many existing SOTA models to achieve good results. In order to address these challenges, we have developed a Transformer-based time series prediction model with contrastive learning for monitoring the status of nuclear power systems. We evaluated the new model on three nuclear power simulation datasets and four power transformer datasets. The experimental results show that the new model's performance is superior to baseline models. We also proved the effectiveness of our improvement through ablation experiments. © 2024 IEEE.

关键词： Prediction models

来源：评论

学校读者我要写书评

暂无评论

Effect of Free-End Torsion on the Corrosion and Mechanical Properties for Mg-3Zn-0.2Ca Alloy

引用

Acta Metallurgica Sinica(English Letters) 2025年第1期38卷 59-70页

作者： Li-Lan Gao Jiang Ma Yan-Song Tan Xiao-Hao Sun Qi-Jun Gao De-Bao Liu Chun-Qiu Zhang Tianjin Key Laboratory for Advanced Mechatronic System Design and Intelligent Control School of Mechanical EngineeringTianjin University of TechnologyTianjin300384China National Demonstration Center for Experimental Mechanical and Electrical Engineering Education Tianjin University of TechnologyTianjin300384China School of Materials Science and Engineering Tianjin University of TechnologyTianjin300384China

Magnesium alloys with excellent degradability and biocompatibility are promising materials for biomedical implants,saving patients the burden of second ***,their mechanical properties and corrosion resistance are significantly below the requirements for implant *** study aims to improve the mechanical and corrosion resistance properties of Mg-3Zn-0.2Ca alloy by pre-torsion treatment,and find out the optimal shear *** rod-shaped Mg-3Zn-0.2Ca alloy specimens were pre-torsion treated at different torsion *** effect of free-end torsion on Mg-3Zn-0.2Ca alloy was characterized through microstructure analysis,mechanical testing,and corrosion ***-torsion treatment can refine grain and induce twins and dislocations in Mg-3Zn-0.2Ca *** surface hardness increases with the increase in torsion *** yield strength and ultimate strength initially increase and then decrease with increasing torsion angle,while ductility decreases with increasing torsion *** with a shear strain of 30%exhibit the highest tensile strength,reaching 284.78±10.62 MPa,with an elongation of 19.37±1.66%.Furthermore,they show a significant improvement in fatigue lives both before and after *** the stress amplitude is 120 MPa,the fatigue lives for specimens without pre-torsion treatment are 54,275 cycles and 4324 cycles before and after pre-corrosion,while they increased significantly to 92,015 cycles and 5050 cycles with the 30%shear strain,***,the 30%shear strain specimens show a significant reduction in corrosion *** conclusion,pre-torsion treatment can effectively modify the microstructure of Mg-3Zn-0.2Ca alloy,enhancing both mechanical properties and corrosion *** optimal shear strain for this improvement is 30%.This study provides a practical method to enhance the mechanical properties and corrosion resistance of Mg-3Zn-0.2Ca alloy,making it more suitable for biomedical implan

关键词： Magnesium alloy Pre-torsion Microstructure Mechanical property Corrosion resistance

来源：评论

学校读者我要写书评

暂无评论

Research on model validation of routing protocol for UAV swarm cooperative disaster relief system

Research on model validation of routing protocol for UAV swa...

引用

2023 International Conference on Computer Application and Information Security, ICCAIS 2023

作者： Wei, Tonghao Liu, Jie Yang, Fei Han, Wenxing Jiang, Wei School of Computer Science/Software University of South China Hunan Hengyang China Science and Technology on Reactor System Design Technology Laboratory Nuclear Power Institute of China Sichuan Chengdu China

ISBN: (纸本)9781510675032

In recent years, with the continuous expansion of unmanned aerial vehicle (UAV) swarm applications and the rapid development of the UAV self-organizing network system, the related security threats have also increased. In this paper, we conduct the communication model of the UAV swarm cooperative disaster relief system by verifying the security attributes of the UAV swarm cooperative disaster relief system based on the dynamic source routing (DSR) protocol and we also analyze and verify their security attributes. Finally, we propose a novel scheme to model, characterize, and verify the security attributes of the UAV swarm communication networks. It provides a formal analysis and verification method for verifying the security attributes of self-organized network systems, simplifying a series of challenging verification processes that come with demonstrating the security attributes of the system through simulation experiments. © 2024 SPIE.

关键词： Formal verification

来源：评论

学校读者我要写书评

暂无评论

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

请选择保存的检索档案：

请选择收藏分类：

通借通还

建议与咨询 留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

请选择保存的检索档案： 新增检索档案 确定 取消

请选择收藏分类： 新增自定义分类 确定 取消

通借通还

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

请选择保存的检索档案：

请选择收藏分类：