检索结果-内蒙古大学图书馆

Distributed multi-target tracking with labeled multi-Bernoulli filter considering efficient label matching

Frontiers of Information technology & Electronic Engineering 2025年第3期26卷 400-414页

作者： Changwen DING Chuntao SHAO Siteng ZHOU Di ZHOU Runle DU Jiaqi LIU School of Astronautics Harbin Institute of TechnologyHarbin 150001China National Key Laboratory of Science and Technology on Test Physics and Numerical Mathematics Beijing 100076China

We propose a distributed labeled multi-Bernoulli(LMB)filter based on an efficient label matching *** distributed LMB filter fusion has the premise that the labels among local densities have already been ***,considering that the label space of each local posterior is independent,such a premise is not practical in many *** achieve distributed fusion practically,we propose an efficient label matching method derived from the divergence of arithmetic average(AA)mechanism,and subsequently label-wise LMB filter fusion is performed according to the matching *** with existing label matching methods,this proposed method shows higher performance,especially in low detection probability ***,to guarantee the consistency and completeness of the fusion outcome,the overall fusion procedure is designed into the following four stages:pre-fusion,label determination,posterior complement,and uniqueness *** performance of the proposed label matching distributed LMB filter fusion is demonstrated in a challenging nonlinear bearings-only multi-target tracking(MTT)scenario.

关键词： Distributed multi-sensor multi-target tracking Labeled multi-Bernoulli filter Arithmetic average fusion Label matching

来源：评论

学校读者我要写书评

暂无评论

Dynamic failure of aramid paper honeycomb under intermediate strain rate loading

引用

Thin-Walled Structures 2025年 215卷

作者： Chen, Meiduo Zhang, Xianglin Xu, Songlin Ma, Hao Yuan, Liangzhu Xie, Yushan Zhang, Xiaoman Wang, Pengfei University of Science and Technology of China Department of Modern Mechanics CAS Key Laboratory for Mechanical Behavior and Design of Materials Anhui Hefei230027 China Beijing Institute of Space Long March Vehicle Beijing100076 China National Key Laboratory of Science and Technology on Test Physics and Numerical Mathematics Beijing100076 China

Investigation of the transformation process of failure mechanism for materials and structures under intermediate strain rate loading is of great significance. To achieve intermediate strain rate loading, a novel experimental technique is proposed using a high-speed-rotating eccentric cam to compress the specimen. The particle velocities and the stresses at both ends of the specimen are measured by the velocity interferometer system for any reflector (VISAR) and by the semiconductor strain gauges, respectively. The paper honeycomb specimens with four thicknesses (i.e. 2 mm, 3 mm, 5 mm, and 10 mm) are tested under strain rates ranging from 0.1 to 15 s-1. Local deformation evolution in the specimen is captured based on high-speed photography and analyzed by the digital image correlation method (DIC). The deformation under intermediate strain rate loading is distinguished by higher particle velocity and lower particle acceleration, which is different from those under the static compression (at lower strain rates) and the Split Hopkinson Pressure bar (SHPB) impacting (at higher lower strain rates). Based on the DIC results, the abnormal size effect of specimen 2 mm is due to the competition between in-plane shear failure and out-of-plane buckling. The theoretical model is then established by introducing two main parameters, i.e. the lateral weakening factor ξ and the dynamic parameter k, to describe respectively the effects of in-plane shearing and strain rate on the out-of-plane wall buckling, and the critical stress for specimen buckling is obtained. The results show that the buckling deformation and the half-wave number for buckling are sensitive to the two parameters. This work provides theoretical and experimental references for the study of thin-walled structures under intermediate strain rate. © 2025 Elsevier Ltd

关键词： Fracture mechanics

来源：评论

学校读者我要写书评

暂无评论

Low-overlap square aperture ptychography with selective scanning

引用

Optics and Laser technology 2025年 190卷

作者： Qiao, Ziling Wen, Xiu Chen, Hang Huang, Guancheng Zhou, Xuyang Li, Ziyang Ji, Yu Liu, Wei Chi, Dazhao Gao, Bin Liu, Shutian Xue, Feng Liu, Zhengjun Li, Yutong School of Physics Harbin Institute of Technology Harbin 150001 China School of Physical Science and Technology Tiangong University Tianjin 300387 China School of Space Information Space Engineering University Beijing 101416 China Optical Imaging Laboratory Harbin Institute of Technology Shenzhen 518055 China National Key Laboratory of Precision Welding & Joining of Materials and Structures Harbin Institute of Technology Harbin 150001 China College of Data Science and Technology Heilongjiang University Harbin 150080 China National Key Laboratory of Science and Technology on Test Physics and Numerical Mathematics Beiiing 100076 China

As an excellent representative of coherent diffraction imaging, ptychography iterative engine plays a crucial role in biomedical imaging and crystal structure analysis. However, the significant challenges regarding imaging speed and throughput have hindered its development in fast imaging. In this paper, we propose a fast square aperture reconstruction method with a low-overlap rate aimed at mitigating the issue of low efficiency. Our approach, employing the Tamura coefficient of gradient (TOG) operator-guided strategy with square aperture, surpasses the performance of previous initial iterations. Enhanced imaging quality is demonstrated by intentionally selecting patterns in the reconstruction stage. Our results illustrate that a high-overlap rate and extensive patterns are no longer indispensable for lensless ptychography. © 2025 Elsevier Ltd

关键词： Coherent diffraction imaging Computational imaging Phase retrieval Ptychography

来源：评论

学校读者我要写书评

暂无评论

Double-stage Metamodel and Its Application in Aerodynamic Design Optimization

引用

Chinese Journal of Aeronautics 2011年第5期24卷 568-576页

作者： ZHANG Dehu GAO Zhenghong HUANG Likeng WANG Mingliang National Key Laboratory of Science and Technology on Aerodynamic Design and Research Northwestern Polytechnical University Xi＇an 710072 China National Key Laboratory of Science and Technology on Test Physics ＆ Numerical Mathematical Beijing 100076 China

Constructing metamodel with global high-fidelity in design space is significant in engineering design. In this paper, a double-stage metamodel （DSM） which integrates advantages of both interpolation metamodel and regression metamodel is constructed. It takes regression model as the first stage to fit overall distribution of the original model, and then interpolation model of regression model approximation error is used as the second stage to improve accuracy. Under the same conditions and with the same samples, DSM expresses higher fidelity and represents physical characteristics of original model better. Besides, in order to validate DSM characteristics, three examples including Ackley function, airfoil aerodynamic analysis and wing aerodynamic analysis are investigated, In the end, airfoil and wing aerodynamic design optimizations using genetic algorithm are presented to verify the engineering applicability of DSM.

关键词： optimization genetic algorithm double-stage metamodel Kriging BP neural network Latin hypercube Parsecmethod

来源：评论

学校读者我要写书评

暂无评论

Characteristic Mode Design of Dual-Band Reconfigurable Frequency Selective Surface

引用

Chinese Journal of Electronics 2022年第6期31卷 1129-1137页

作者： NING Zihao LI Mengmeng DING Dazhi AI Xia LIU Jiaqi Department of Communication Engineering Nanjing University of Science and Technology National Key Laboratory of Science and Technology on Test Physics and Numerical Mathematics

In this paper, a characteristic mode design of dual-band reconfigurable frequency selective surface(RFSS) with transmission/reflection band is presented. Through the visualization of modal behavior, the theory of characteristic modes(TCM) is used to guide design from a physical perspective. At first, the dominant modes of two basic structures that have a major impact on reflection are clarified by observing the modal *** appropriate combination of the two structures forms an initial element with bandpass properties. Then, the positive-intrinsic-negative(PIN) diode is placed in the middle of the microstrip line and as the state shifts from ON to OFF, the dominant mode resonant frequency of the microstrip line shifts upward. Such a feature can be used to design the transmission/reflection RFSS. Experimentally, a dual-band RFSS operating at 8.8 GHz and 10.4 GHz is designed and fabricated. The measured results that agree with the full-wave simulation validate the proposed TCM-based design.

关键词： dual-band reconfigurable frequency selective surface dual-band RFSS positive-intrinsic-negative diode theory of characteristic modes characteristic mode design full-wave simulation transmission band p-i-n diodes modal behavior visualization bandpass properties microstrip lines microstrip line dominant mode resonant frequency PIN diode microwave filters frequency selective surfaces TCM-based design reflection band transmission RFSS microwave diodes band-pass filters microstrip filters reflection RFSS

来源：评论

学校读者我要写书评

暂无评论

Dispersive FDTD scheme with conformal technology for analyzing electromagnetic scattering of inhomogeneous plasma array

Dispersive FDTD scheme with conformal technology for analyzi...

引用

IET International Radar Conference 2015

作者： Ai, Xia Liu, Shendong Zhang, Shengjun Wang, Mingliang Liu, Jiaqi Meng, Gang Zhou, Hongchao National Key Laboratory of Science and Technology on Test Physics and Numerical Mathematical China

ISBN: (纸本)9781849199940

In this paper, a dispersive conformal FDTD method have been proposed to accurate model the interface between two adjacent dispersive mediums. The method is based on the technology of area average between two adjacent dispersive interfaces, which is different from existing dispersive conformal FDTD schemes which involve with the interface between free space and dispersive medium. numerical results show the proposed method would enhance the accurate level compared to the staircasing FDTD scheme involved in the inhomogeneous plasma.

关键词： numerical methods

来源：评论

学校读者我要写书评

暂无评论

Higher order shift operater FDTD scheme for scattering of cloaking structure

Higher order shift operater FDTD scheme for scattering of cl...

引用

IET International Radar Conference 2015

作者： Ai, Xia Zhang, Shengjun Wang, Mingliang Wang, Weidong Liu, Jiaqi Liu, Chengguo Liu, Xuemei National Key Laboratory of Science and Technology on Test Physics and Numerical Mathematical China

ISBN: (纸本)9781849199940

In this paper, a higher-order shift operater (SO) FDTD scheme with second-order accuracy in time and fourth-order in space has been proposed to accurately model scattering of perfect electronic conductor coated with cloaking structures. Several different electromagnetic parameters of the cloaks are taken into account using SO-FDTD method. numerical results indicate that the proposed method is more accuracy than the traditioinal method maintaining the same grid size. Scattering of different kinds of simplified cylindrical cloaks including thickness and loss are presented and could be served as further study on this subject.

关键词： Finite difference time domain method

来源：评论

学校读者我要写书评

暂无评论

The research on the effects of an active FSS with circle element on the characteristics of Radar Absorbing Materials

The research on the effects of an active FSS with circle ele...

引用

IET International Radar Conference 2015

作者： Wang, Ming-Liang Zhang, Sheng-Jun Liu, Jia-Qi Wang, Wei-Dong Ai, Xia Liu, Shengdong Liang, Wei National Key Laboratory of Science and Technology on Test Physics and Numerical Mathematical Beijing China

ISBN: (纸本)9781849199940

An active frequency selective surface (FSS) is designed, and is combined with Radar Absorbing Materials to form a composite absorbing structure. Based on the equivalent theory that the PIN diode can be regarded as resistance, the voltage-loading resistance of active FSS element is researched for RAM containing FSS, and the electromagnetic wave reflectivity performance is analyzed. The influence of active FSS design parameters on the reflectivity of RAM is researched, and the FSS design parameters include the voltage-loading manner, the resistance parameter, and the position in the RAM. The research result shows that the resonance frequency of RAM containing FSS can be dynamically adjusted from 3GHz to 4GHz by changing voltage-loading resistance of active FSS, and the reflectivity can be reduced from -13dB to -35dB.

关键词： Reflection

来源：评论

学校读者我要写书评

暂无评论

Study on reflection selective structure on near infrared

Study on reflection selective structure on near infrared

引用

International Conference on Electronics and Optoelectronics

作者： Li, Yizhou Wang, Daorong Liu, Jiaqi Li, Hongjie Zhao, Juyan National Key Laboratory of Science and Technology on Test Physics and Numerical Mathematical Beijing China

ISBN: (纸本)9781612842738

The paper bring forward a design of multilayer structure which has a high reflectivity for 1.82μm laser beam and a high absorptivity for 1.48μm laser beam. The experiment reveal that the absorptivity of the film reach to 95% at incidence angle from 0 to 40 for 1.48μm laser beam and has a high reflectivity for 1.82μm high power laser at incidence angle of 30o at laser power density above 500w/cm2. © 2011 IEEE.

关键词： Reflection

来源：评论

学校读者我要写书评

暂无评论

The role of single loading dielectric layer on properties of Frequency Selective Surfaces

The role of single loading dielectric layer on properties of...

引用

International Workshop on Metamaterials (Meta)

作者： Zhang, S. J. Liu, J. Q. Wang, M. L. Ms, W. M. Liang, W. Liu, X. M. Hou, X. C. National Key Laboratory of Science and Technology on Test Physics & Numerical Mathematics

ISBN: (纸本)9781467328081

Frequency selective surfaces (FSS) have attracted researchers from many subjects for decades for its tempting applications such as for radome radar cross section (RCS) reduction, sub-reflector, et. al. Many studies was focused on different type FSS, such as unit shape, dielectric loading, layers of FSS. And it is of popular consideration that double dielectric loading on both sides of FSS be an ideal configuration. In this paper, the type of single side loading, which is more similar to the practical configuration, was studied with the numerical method. And it is found that both the thickness of thick loading layer and the constant of the thin substrate play key roles to the properties of FSS.

关键词： frequency selective surfaces loading LOADING dielectric layer side load numerical methods sidings

来源：评论

学校读者我要写书评

暂无评论

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

请选择保存的检索档案：

请选择收藏分类：

通借通还

建议与咨询 留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

请选择保存的检索档案： 新增检索档案 确定 取消

请选择收藏分类： 新增自定义分类 确定 取消

通借通还

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

请选择保存的检索档案：

请选择收藏分类：