检索结果-内蒙古大学图书馆

9th China International Conference on Electricity Distribution, CICED 2021

作者： Qian, Minhui Zhao, Dawei Zhao, Liang Zhu, Lingzhi Wu, Fubao Chen, Ning Qin, Wenping Xu, Chang Jiangsu Eng. Technol. Res. Ctr. for Ener. Storage Conversion and Applic. China Elec. Pwr. Res. Inst. State Key Laboratory of Operation and Control of Renewable Energy and Storage Systems Nanjing China Shanxi Key Lab of Power System Operation and Control Taiyuan University of Technology Taiyuan China College of Energy and Electrical Engineering Hohai University Nanjing China

ISBN: (纸本)9781728192291

High share of renewable energy will be one of the basic features of power systems in the future around the world. Compared with photovoltaic (PV) and wind power, concentrating solar power (CSP) equipped with heat storage system has similar regulation characteristics with thermal power units, and it can effectively overcome the intermittent and volatility of PV and wind power generation. Meanwhile, the CSP units can strongly support the voltage, frequency and short-circuit capacity of power systems. So, CSP is a very promising power generation technology for the future power system. The CSP unit has better ramp ability than thermal power unit, and can generally reach a speed between 2% and 5% of rated power per minute. Stated thus, the CSP unit has a good potential to participate in the primary frequency regulation of power grid. At present, there are many researches on the performance of each subsystem of the CSP unit in worldwide, and there are also some theoretical researches on the participation of CSP unit in the dispatching operation of power system. However, there is a lack of research reports on CSP plant's participation in the primary frequency regulation of the power grid, which is an urgently needed feature for the future power systems with high share of renewable energy. In this paper, a model with primary frequency regulation ability of CSP unit is established in DIgSILENT powerFactory software. A revised two-area four-machine system is used to investigate the CSP unit's participation in primary frequency regulation of power system. The simulation results show the good frequency regulation performance of CSP unit, which can effectively support the stable operation of power system with high share of renewable energy in the future. © 2021 IEEE.

关键词： Concentrated solar power

来源：评论

学校读者我要写书评

暂无评论

Research on relay setting attack defense in power systems based on a three-layer optimization model

引用

Frontiers in energy Research 2024年 12卷

作者： Ren, Liu Binyuan, Yan Hengdao, Guo Junrong, Liu Yihua, Zhu Yun, Fu Liang, Tu Zeyuan, Zhou State Key Laboratory of HVDC Electric Power Research Institute China Southern Power Grid Guangzhou China National Energy Power Grid Technology R&D Centre Guangzhou China Guangdong Provincial Key Laboratory of Intelligent Operation and Control for New Energy Power System Guangzhou China CSG Key Laboratory for Power System Simulation Electric Power Research Institute China Southern Power Grid Guangzhou China Information Centre of Guizhou Power Grid Co. Guizhou China

With the intelligent development of power systems, the number of relays continues to increase. Differences in manufacturers, systems, and protocols lead to growing security risks. Tampering with relay settings could potentially cause power outages or even system instability. Consequently, relay settings have gradually become a key target for cyberattacks, particularly in smart grids where traditional defense measures struggle to effectively address complex and diverse attack scenarios. To address this issue, this paper proposes a three-layer optimization defense model based on game theory, designed to adapt to various attack scenarios. The core methodology of this model includes a three-layer structure: The first layer optimizes the protection level of each relay by allocating limited defense budgets. The second layer analyzes the potential system damage based on the attacker’s strategy choices. The third layer comprehensively calculates system losses to evaluate the effectiveness of defense plans. Through layer-by-layer optimization of budget allocation, the model minimizes the unsupplied energy loss caused by relay setting attacks. Compared to existing methods, this model not only improves defense effectiveness under resource constraints but also addresses multiple complex attack scenarios. Experimental results demonstrate that this model significantly enhances the system’s defense capabilities and effectively reduces the impact of attacks on system security operations. Copyright © 2024 Ren, Binyuan, Hengdao, Junrong, Yihua, Yun, Liang and Zeyuan.

关键词： Budget control

来源：评论

学校读者我要写书评

暂无评论

Selective Preferred Orientation for High-Performance Antimony Selenide Thin-Film Solar Cells Via Substrate Surface Modulation

SSRN

引用

SSRN 2022年

作者： Zhou, Jing Zhu, Jiawei He, Weilan Cao, Yu Pang, Jinbo Ni, Jian Zhang, Jianjun School of Chemical Engineering Northeast Electric Power University Jilin132012 China Key Laboratory of Modern Power System Simulation and Control & Renewable Energy Technology Ministry of Education School of Electrical Engineering Northeast Electric Power University Jilin132012 China University of Jinan Jinan250022 China College of Electronic Information and Optical Engineering Nankai University Tianjin300350 China

Antimony selenide (Sb2Se3) has rapidly emerged in the field of photovoltaics using one-dimensional crystal structure. However, the power conversion efficiency (PCE) of Sb2Se3 solar cells is influenced by the orientation of the Sb2Se3 photoactive layers. In this study, we investigate the influence of substrate properties on the preferred orientation and microstructure of Sb2Se3 films systematically. With the rise of substrate surface temperature and the decline of substrate surface bonding energy, the preferred orientation of the Sb2Se3 films altered from (hk0) to (hk1) and finally to (002). After summarizing the performance of different preferentially oriented Sb2Se3 solar cells, the results showed that the (hk0)-preferentially oriented devices exhibited a poor performance of less than 1.1%. As the preferred orientation of Sb2Se3 absorbers changed from (hk0) to (hk1), the carrier transport changed from inter-ribbon charge hopping to transportation along the (Sb4Se6)n ribbons. This enhanced the carrier transport efficiency, thereby leading to the enhancement of the PCE to 2%–3%. Furthermore, when the (002) texture coefficient (TC) of the Sb2Se3 films was between 1.8 and 3.6, the PCE of the devices was further enhanced to above 3.5%. A maximum PCE of 4.79% can be obtained when the (002) TC was 3.24. This study reveals the relationship between the Sb2Se3 film preferred orientation and device performance, and demonstrates an effective way to precisely control the Sb2Se3 film microstructure to obtain a high PCE. © 2022, The Authors. All rights reserved.

关键词： Selenium compounds

来源：评论

学校读者我要写书评

暂无评论

Conditional Adversarial Domain Adaption based on Self-attention

Journal of Network Intelligence

引用

Journal of Network Intelligence 2022年第1期7卷 175-188页

作者： Zhao, Li-Quan Zhang, Yu-Peng Teng, Zi-Ming Jiang, Zi-Cong Cui, Ying Kan, Zhong-Feng Key Laboratory of Modern Power System Simulation and Control & Renewable Energy Technology Ministry of Education Northeast Electric Power University Jilin132012 China College of information and communication Jilin University Changchun130012 China Graduate school of Information Science and Electrical Engineering Kyushu University Fukuoka819-0395 Japan Zhuhai Power Supply Bureau Guangdong Electric Power Corporation Zhuhai519000 China Jilin Power Supply Bureau Jilin Electric Power Corporation Jilin132012 China

Transfer learning is a deep learning method. It transforms knowledge in the source domain and feeds it to the target domain to improve the performance of the target domain model. The conditional adversarial domain adaption method is one of a number of transfer learning methods. It uses Resnet as the feature extraction network;however, Resnet can only determine the relationship between local features, and so its feature extraction accuracy is limited. To overcome this problem, a self-attention layer has been designed in order to determine the relationship among all features. This layer is added between the fourth layer and fifth layer of Resnet. Besides, a cross-entropy function is introduced into loss function, and a sigmoid layer is designed and used as the out layer in conditional adversarial domain adaption. These produce gradient disappearance in the deep network, and influence the discriminator training effect. To solve that problem, a least squares function is used as to design the loss function. The new type of loss function does not require the sigmoid function. Using theoretical analysis, we explain how this new loss function can be used to solve the gradient disappearance problem, thus rendering the network structure more stable. We compare our proposed method with other datasets, including Joint Adaptation Networks, adversarial domain adaptation, conditional adversarial domain adaption, Resnet-50, domain-adversarial neural network on imageCLEF-DA, Office-Home, and Office-31. Our simulation results show that the proposed conditional adversarial domain adaption based on self-attention method has the fastest convergence speed and highest accuracy the among different datasets. © 2022, Taiwan Ubiquitous Information CO LTD. All rights reserved.

关键词： Computer vision

来源：评论

学校读者我要写书评

暂无评论

Fault Detection Method for Insulators Using Improved YOLOv4

Journal of Network Intelligence

引用

Journal of Network Intelligence 2022年第4期7卷 818-834页

作者： Zhao, Li-Quan Jiang, Zi-Cong Teng, Zi-Ming Jia, Yan-Fei Key Laboratory of Modern Power System Simulation and Control & Renewable Energy Technology Ministry of Education Northeast Electric Power University 168 Changchun Road Jilin132012 China Graduate school of Information Science and Electrical Engineering Kyushu University Fukuoka819-0395 Japan College of information and communication Jilin University Changchun130012 China School of Electrical and Information Engineering Beihua University Jilin132013 China

A defective insulator detection method based on improved You Only Look Once version 4 (YOLOv4) is proposed to improve the precision of defective insulator detection. This method designs a dual-branch attention block by simulating the attention process of the human eye, and introduces it into the backbone of YOLOv4 to extract richer information on defective insulator features. To make the output feature map of shallow layer network fuse more different scale features, a path aggregation network has been designed. To improve detection accuracy, the spatial pyramid pooling has been replaced by atrous spatial pyramid pooling. A dynamic non-maximum suppression method is proposed to improve defective insulator detection accuracy. It employs an adaptive threshold control strategy and weighted operation to full use of the predicted box. We compare our method with defective insulator detection methods based on YOLO and R-CNN. Our simulation results show that the proposed method is more accurate than defective insulator detection methods based on YOLO, and has a faster detection speed than methods based on R-CNN. Compared with the defective insulator detection method based on R-CNN that has the highest mean average precision, the mean average precision of the proposed method is lower, but its detection speed is faster. Compared with YOLOv4, its detection speed is slower, but the mean average precision is higher. The proposed method strikes a satisfactory tradeoff between detection speed and mean average precision. © 2022, Taiwan Ubiquitous Information CO LTD. All rights reserved.

关键词： Object detection

来源：评论

学校读者我要写书评

暂无评论

Analysis and suppression of low-frequency oscillation of photovoltaic cells with inertia control

Analysis and suppression of low-frequency oscillation of pho...

引用

China International Electrical and energy Conference (CIEEC)

作者： Zhenyang Wang Gangui Yan Yue Zhao Jili Peng Dazhong Wang Shuang Ren Dept. Ministry of Education Key Laboratory of Modern Power System Simulation control and Green Power Technology Northeast Electric Power University Jilin China Dept. State Grid Hengyang Power Supply Branch State Grid Hunan Power Supply Hunan China

Aiming at the problem of low-frequency oscillation when photovoltaic power generation is connected to weak AC system, a linearization model of photovoltaic power generation is established, which ignores current inner loop and considers inertia control. The influence of various leading factors on low-frequency oscillation modes of photovoltaic power generation is analyzed. Finally, a low-frequency oscillation stabilizer (SSDC) is designed according to the phase compensation method to suppress the low-frequency oscillation of power system. The results show that the increase of input power of DC capacitor and the decrease of proportional control parameters of DC voltage loop and PLL will lead to the decrease of system damping and stability. Finally, the electromagnetic simulation model of weak AC system with photovoltaic power generation is built on PSCAD/EMTDC platform, which verifies the validity of eigenvalue analysis results and SSDC.

关键词：

来源：评论

学校读者我要写书评

暂无评论

Optimization control Strategy of Pumped Storage power Station Considering Cost Allocation

Optimization Control Strategy of Pumped Storage Power Statio...

引用

International Conference on power system technology (powerCON)

作者： Jun Yan Qinglong Song Qi Guo Lijian Xin Fancheng Meng Shuo Yu Jiaxu Zhou Cuiping Li Junhui Li Inner Mongolia Power (Group) Co. Ltd. Hohhot China Key Laboratory of Modern Power System Simulation and Control & Renewable Energy Technology Ministry of Education Northeast Electric Power University Jilin China Power Dispatching and Control Branch Inner Mongolia Power (Group) Co. Ltd. Hohhot China Inner Mongolia Electric Power (Group) Co. Ltd. Inner Mongolia Electric Power Research Institute Branch Hohhot China

Against the backdrop of the increasing proportion of new energy generation, pumped storage, as the main energy storage method, face problems of low utilization and poor economic benefits. To improve the enthusiasm and overall efficiency of pumped storage power stations, this article proposes an optimized control strategy for pumped storage power stations that takes into account cost sharing. This strategy combines the PSS allocation system operation rules and control strategies to improve the utilization of PSS capacity by expanding its application scenario range, and to increase its enthusiasm for extraction by increasing rental income; This article takes a regional power grid in northwest China as an example for analysis, and the results show that the proposed strategy can effectively improve the utilization level and economic benefits of PSS.

关键词：

来源：评论

学校读者我要写书评

暂无评论

simulation Testing of Large-Scale Grid-Connected Wind power with energy Storage system Based on Active Support Performance Evaluation Indices

Simulation Testing of Large-Scale Grid-Connected Wind Power ...

引用

Electrical Engineering and Automation (IFEEA), International Forum on

作者： Yihua Zhu Yun Hu Liang Tu Mingzhang Su Chao Luo State Key Laboratory of HVDC Electric Power Research Institute CSG Guangzhou China National Energy Power Grid Technology R&D Centre Guangzhou China Guangdong Provincial Key Laboratory of Intelligent Operation and Control for New Energy Power System Guangzhou China CSG Key Laboratory for Power System Simulation Electric Power Research Institute China Southern Power Grid Guangzhou China

This paper establishes simulation modeling for large-scale grid connected wind power with energy storage system (ESS). The conventional grid-following (GFL) based ESS is used as a reference object to test the active support performance of large-scale grid-connected wind power with grid-forming (GFM) based ESS with active support performance evaluation indices in different scenarios. (1) Small disturbance evaluation indices: The point of common coupling (PCC) frequency/voltage drop depth and recovery time. (2) Large disturbance evaluation indices: The PCC frequency/voltage drop depth and rise height after fault removal. The output active/reactive power drop depth and rise height/recovery time after fault removal. (3) Island capability evaluation indices: The PCC frequency/voltage fluctuation amplitude at the moment of switching and system stability after switching.

关键词：

来源：评论

学校读者我要写书评

暂无评论

General Impedance Modeling for Modular Multilevel Converter with Grid-forming and Grid-following control

arXiv

引用

arXiv 2024年

作者： Sun, Chu Zhang, Fei Xiao, Huafeng Wang, Na Chen, Jikai The School of Electrical Engineering and Computer Science KTH Royal Institute of Technology Stockholm11428 Sweden The School of Electrical Engineering Southeast University Nanjing210096 China The School of Automation Science and Electrical Engineering Beihang University Beijing100191 China The Key Laboratory of Modern Power System Simulation and Control & Renewable Energy Technology Ministry of Education Northeast Electric Power University Jilin132012 China

Modular multilevel converter (MMC) has complex topology, control architecture and broadband harmonic spectrum. For this, linear-time-periodic (LTP) theory, covering multi-harmonic coupling relations, has been adopted for MMC impedance modeling recently. However, the existing MMC impedance models usually lack explicit expressions and general modeling procedure for different control strategies. To this end, this paper proposes a general impedance modeling procedure applicable to various power converters with grid-forming and grid-following control strategies. The modeling is based on a unified representation of MMC circuit as the input and output relation between the voltage or current on the AC side and the exerted modulation index, while the control part vice versa, thereby interconnected as closed-loop feedback. With each part expressed as transfer functions, the final impedance model keeps the explicit form of harmonic transfer function matrix, making it convenient to directly observe and analyze the influence of each part individually. Thereby the submodule capacitance is found as the main cause of difference between MMC impedance compared to two-level converter, which will get closer as the capacitance increases. Effectiveness and generality of the impedance modeling method is demonstrated through comprehensive comparison with impedance scanning using electromagnetic transient simulation. Copyright © 2024, The Authors. All rights reserved.

关键词： Harmonic analysis

来源：评论

学校读者我要写书评

暂无评论

reversible in-situ exsolution of Fe catalyst in La0.5Sr1.5Fe1.5Mo0.5O6-δ anode for SOFCs 16

reversible in-situ exsolution of Fe catalyst in La0.5Sr1.5Fe...

引用

16th International Symposium on Solid Oxide Fuel Cells, SOFC 2019

作者： Qi, H. Yang, T. Li, W. Ma, L. Hu, S. Shi, W. Sabolsky, E.M. Zondlo, J. Hart, R. Hackett, G.A. Liu, X. Department of Mechanical and Aerospace Engineering West Virginia University MorgantownWV26506 United States National Energy Technology Laboratory MorgantownWV26505 United States Oak Ridge Institute for Science and Education P.O. Box 117 Oak RidgeTN37830 United States Department of Energy and Power Engineering State Key Laboratory of Control and Simulation of Power System and Generation Equipments Tsinghua University Beijing10083 China GE Global Research Centre NiskayunaNY12309 United States

ISBN: (纸本)9781607688747

In-situ exsolution is widely considered to be an efficient and cost-effective method to enhance the electrochemical performance of a ceramic anode in solid oxide fuel cells (SOFCs). In this study, by controlling the non-stoichiometry of Sr2Fe1.5Mo0.5O6-δ with A-site doping, evenly distributed Fe nano-particles (~100 nm) were obtained on surface of La0.5Sr1.5Fe1.5Mo0.5O6-δ (LSFM) when treated in hydrogen. In a redox environment, excellent exsolution-dissolution reversibility was also demonstrated. Electrical conductivity relaxation (ECR) and electrochemical impedance spectroscopy (EIS) were employed to evaluate the surface reaction kinetics change during exsolution. The surface exchange coefficient (kex) was increased by 1.5 to 2 times with Fe exsolution. Based on distribution of relaxation time (DRT) analysis, the polarization resistance (Rp) associating with surface process was reduced in the first few hours. Both results revealed an enhanced surface reaction kinetics which mainly benefits from the high catalytic activity of exsolved nano-particles to H2 adsorption and dissociation process. © The Electrochemical Society.

关键词： Electrochemical impedance spectroscopy

来源：评论

学校读者我要写书评

暂无评论

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

请选择保存的检索档案：

请选择收藏分类：

通借通还

建议与咨询 留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

请选择保存的检索档案： 新增检索档案 确定 取消

请选择收藏分类： 新增自定义分类 确定 取消

通借通还

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

请选择保存的检索档案：

请选择收藏分类：