检索结果-内蒙古大学图书馆

作者： Wang, Xixi Liu, Maochang Chen, Qingyun Zhang, Kai Chen, Jie Wang, Meng Guo, Penghui Guo, Liejin International Research Center for Renewable Energy State Key Laboratory of Multiphase Flow in Power Engineering Xi'An Jiaotong University Shaanxi 710049 China

A series of CdS and CdS/CNTs photocatalysts were successfully prepared by hydrothermal method and they were characterized by X-ray diffraction (XRD), scanning electron microscope (SEM), UV-visible optical absorption spectra (UV-Vis), etc. By studying their photocatalytic properties, it is found that, for CdS, photocatalysts prepared in appropriate alkaline environment presented higher hydrogen production activity, reaching 794.6 μmol h-1 g-1;the photocatalytic activity of CdS was obviously enhanced by combining it with CNTs via a special two-step hydrothermal method, and the corresponding hydrogen production rate reached 1.771 mmol h-1 g -1;the photocatalytic activity was further improved by loading co-catalyst NiS, achieving 12.13 mmol h-1 g-1. © 2013, Hydrogen Energy Publications, LLC. Published by Elsevier Ltd. All rights reserved.

关键词： Cadmium sulfide

来源：评论

学校读者我要写书评

暂无评论

ZnS/ZnO heterojunction as photoelectrode: Type II band alignment towards enhanced photoelectrochemical performance

ZnS/ZnO heterojunction as photoelectrode: Type II band align...

引用

作者： Guo, Penghui Jiang, Jiangang Shen, Shaohua Guo, Liejin International Research Center for Renewable Energy State Key Laboratory of Multiphase Flow in Power Engineering Xi'An Jiaotong University Shaanxi 710049 China

Heterojunction structures are attracting lots of attention for enhancing the electron injection across the interface. The ZnS/ZnO one-dimensional heterojunction film was firstly prepared via a chemical sulfidization following hydrothermal reaction. The heterostructure was characterized as ZnS(blende)/ZnO(wurtzite) shell-core nanorods via XRD, SEM and TEM. A type II band alignment structure of ZnS/ZnO composite was synthesized via a temperate condition proved by PLS and XPS. The values for valence band offset (VBO) and conduction band offset (CBO) were calculated to be 0.96 eV and 1.25 eV, respectively. The special electron structure in the heterojunction helped reduce the energy barrier height at the interface and enhance the separation of photo-generated carriers. Thus, the photoelectrochemical performance was highly improved, and a photocurrent density of 380 μA/cm2 at 0.9 V (vs. Ag/AgCl) was obtained. © 2013, Hydrogen Energy Publications, LLC. Published by Elsevier Ltd. All rights reserved.

关键词： Heterojunctions

来源：评论

学校读者我要写书评

暂无评论

Fabricating CdS/BiVO4 and BiVO4/CdS heterostructured film photoelectrodes for photoelectrochemical applications

Fabricating CdS/BiVO4 and BiVO4/CdS heterostructured film ph...

引用

作者： Jiang, Jiangang Wang, Meng Li, Rong Ma, Lijing Guo, Liejin State Key Laboratory of Multiphase Flow in Power Engineering International Research Center of Renewable Energy Xi'An Jiaotong University Shaanxi 710049 China

The photoelectrochemical (PEC) properties of heterostructured CdS/BiVO 4 and BiVO4/CdS film electrodes on conducting glass for hydrogen production under visible light were investigated. These two types heterostructured film electrodes were prepared using spin coating method and ultrasonic spray pyrolysis method. The structural analyses of the prepared films were determined by using XRD, SEM, EDX and UV-vis. Photoelectrochemical measurements were carried out in a convenient three electrodes cell with 0.5 M Na2SO3 aqueous solution. In order to investigate band gap influence of electrode PEC property, a series ITO/Cd1-xZn xS/BiVO4 and ITO/BiVO4/Cd1-xZn xS (x = 0 ∼ 1) film electrodes were also synthesized. After PEC test, a maximum photocurrent density from ITO/CdS/BiVO4 film electrode was confirmed. The maximum photocurrent density, 3 times and 113 times as that of single CdS film electrode and single BiVO4 film electrode, respectively. Incident photon to current conversion (IPCE) of as prepared film electrodes were measured and the value were 65% (ITO/CdS/BiVO 4), 22% (single CdS film) and 10% (ITO/BiVO4/CdS) at 480 nm with 0.3 V external bias. Comparison with ITO/BiVO4/CdS electrode and single Cd1-xZnxS electrodes, the heterostructured ITO/CdS/BiVO4 electrode can effectively suppress photogenerated electron-hole recombination and enhance light harvesting. Therefore, the ITO/CdS/BiVO4 electrode gave the maximum photocurrent density and IPCE value. © 2013, Hydrogen Energy Publications, LLC. Published by Elsevier Ltd. All rights reserved.

关键词： Bismuth compounds

来源：评论

学校读者我要写书评

暂无评论

Synthesis of uniform ZnO/ZnS/CdS nanorod films with ion-exchange approach and photoelectrochemical performances

Synthesis of uniform ZnO/ZnS/CdS nanorod films with ion-exch...

引用

作者： Jiang, Jiangang Wang, Meng Ma, Lijing Chen, Qingyun Guo, Liejin State Key Laboratory of Multiphase Flow in Power Engineering International Research Center of Renewable Energy Xi'An Jiaotong University Shaanxi 710049 China

The uniform ZnO/ZnS/CdS core-shell nanorod film was synthesized by a two-step ion-exchange method. The crystal structure, morphology, composition and optical property of as-prepared films were characterized by X-ray diffraction (XRD), Raman, Scanning electron microscope (SEM), Transmission electron microscope (TEM), Energy dispersive X-ray Detector (EDX) and UV-vis techniques. The results showed that the ZnO nanorod arrays can be used as sacrificial templates to synthesize uniform ZnS layer and further transform into CdS by simple ion-exchange approach. The CdS content in the films can be adjusted easily by changing the reaction temperature. The intimate contact between core and shell can be observed by high-resolution TEM image, which decrease the crystal boundary potential barrier and then facilitate the photogenerated charges transfer between the different phases. In this experiment, the ZnO/ZnS/CdS nanorod films were used in the photoelectrochemical (PEC) hydrogen production. And it is found that the film prepared at 70 C (first step) and 100 C (second step) gives a maximum photocurrent density and photo conversion efficiency. © 2013, Hydrogen Energy Publications, LLC. Published by Elsevier Ltd. All rights reserved.

关键词： Cadmium sulfide

来源：评论

学校读者我要写书评

暂无评论

Experimental study on loop heat pipe with flat evaporator at different tilt angles

引用

Hsi-An Chiao Tung Ta Hsueh/Journal of Xi'an Jiaotong University 2013年第5期47卷 38-43页

作者： Long, Yan Wei, Jinjia Lü, Xiao State Key Laboratory of Multiphase Flow in Power Engineering Xi'an Jiaotong University Xi'an 710049 China

To realize highly efficient heat dissipation of electronics, a loop heat pipe (LHP) with a flat evaporator was designed to study its operation characteristics at the tilt angles of 0°, 30°, 45°, 60°, 90° with an improved evaporator structure and a well arranged pipes which can reduce heat loss due to back conduction and improve inner flow performance. The results show that the LHP with inclination has a lower power to start up than the horizontal one, and at the same heat load, the operation temperature of the evaporator is much lower and the system is easier to reach a steady state with less temperature oscillations. However, there is slight difference in operating performance for the LHP at different title angles. The thermal resistance decreases with an increase in the heat load and a steady state occurs at last. The thermal resistance is larger for the horizontal case than that for the inclination case at the same heat load. The thermal resistances are very different at different tilt angles at low heat load, but the difference is small at high heat load.

关键词： Thermal load

来源：评论

学校读者我要写书评

暂无评论

Evolution of nanofluid rayleigh-bénard flows between two parallel plates: A mesoscopic modeling study

引用

Journal of Nanotechnology in engineering and Medicine 2013年第4期4卷 040905-1-040905-9页

作者： Lu, Gui Duan, Yuan-Yuan Wang, Xiao-Dong Key Laboratory for Thermal Science and Power Engineering MOE Tsinghua University Beijing 100084 China Institute of Thermal Engineering Beijing Jiaotong University Beijing 100044 China State Key Laboratory of Alternate Electrical Power System with Renewable Energy Sources North China Electric Power University Beijing 102206 China Beijing Key Laboratory of Multiphase Flow and Heat Transfer for Low Grade Energy North China Electric Power University Beijing 102206 China

The developing and developed nanofluid Rayleigh-Bénard flows between two parallel plates was simulated using the mesoscopic thermal lattice-Boltzmann method (LBM). The coupled effects of the thermal conductivity and the dynamic viscosity on the evolution of Rayleigh-Bénard flows were examined using different particle volume fractions (1-4%), while the individual effects of the thermal conductivity and the dynamic viscosity were tested using various particle sizes (11 nm, 20 nm, and 30 nm) and nanoparticle types (Al 2O3, Cu, and CuO2). Two different heating modes were also considered. The results show that Rayleigh-Bénard cell in nanofluids is significantly different from that in pure fluids. The stable convection cells in nanofluids come from the expansion and shedding of an initial vortex pair, while the flow begins suddenly in pure water when the Rayleigh number reaches a critical value. Therefore, the average Nusselt number increases gradually for nanofluids but sharply for pure liquids. Uniform fully developed flow cells with fewer but larger vortex pairs are generated with the bottom heating with nanofluids than with pure liquid, with extremely tiny vortexes confined near the top heating plate for top heating. The number of vortex pairs decreases with increasing nanoparticle volume fraction and particle diameter due to the increasing of dynamic viscosity. The average Nusselt number increases with the increasing Rayleigh number, while decreases with the increasing nanoparticle diameters. The nanoparticle types have little effect on the Rayleigh-Bénard flow patterns. The Rayleigh-Bénard flows are more sensitive with the dynamic viscosity than the thermal conductivity of nanofluids. Copyright © 2013 by ASME.

关键词： Nanoparticles

来源：评论

学校读者我要写书评

暂无评论

Simulation of hemodynamics in portal vein hypertension using CFD

引用

医用生物力学 2013年第S1期28卷 99-101页

作者： Xiao Li Yansong Pu Peng Nie Zongfang Li Bin Chen State Key Laboratory of Multiphase Flow in Power Engineering Xi'an Jiaotong University Second Affiliated Hospital Xi'an Jiaotong University Department of Radiology Huaihe Hospital of Henan University

Introduction Liver cirrhosis generally occurs with the hemodynamic changes during the portal vein hypertension and finally leads to the atrophy of the right lobe of the liver and hepatic failure^[1].According to the hemodynamic changes,a hypothesis has been proposed that the liver volume is related to the istribution of blood from the splenic vein（SV）that involves nutrition from spleen and pancreas^[2,3].The objective of the present paper is to simulate the blood flow in real models of portal vein hypertension and validate the hypothesis using computational fluid dynamics（CFD）*** This study includes 2 patients with liver cirrhosis and a set of 4 normal subjects.

关键词： cirrhosis hemodynamic nutrition pancreas splenic atrophy hypothesis validate finally spleen

来源：评论

学校读者我要写书评

暂无评论

Study on ignition delay times of dimethyl ether/propane/O2/Ar mixtures at elevated pressures

Study on ignition delay times of dimethyl ether/propane/O2/A...

引用

9th Asia-Pacific Conference on Combustion, ASPACC 2013

作者： Hu, Erjiang Pan, Lun Zhang, Zihang Huang, Zuohua State Key Laboratory of Multiphase Flow in Power Engineering Xi'an Jiaotong University No.28 Xianning West Road Xi'an Shaanxi 710049 China

Ignition delay times of dimethyl ether (DME) and propane blends were measured in a shock tube at varied DME blending ratios (0%, 20%, 50%, 80%, 100%), equivalence ratios (0.5, 1.0, 2.0), temperatures (1100-1500 K) and pressures of 20 atm. Mechanism validations were conducted using different chemical kinetic models. A new C5 chemical model with DME sub-model was developed and it can well predict experimental ignition delay times of pure propane, DME and their blends. Experimental and numerical results show that with the decrease of temperature, the ignition delay times increase and the activation energy decreases slightly. With the increase of equivalence ratio, ignition delay times increase for propane and decrease for DME in this study. Ignition delay times decrease with the increase of DME blending ratio and the decrease rates become larger with the increase of equivalence ratio. The peak values of H and OH mole fraction increase with increasing the DME blending ratio, and they promote the ignition of DME/propane blends. Sensitivity analysis shows that the reaction rates of R1 and R353 increase with the increase of DME blending ratio and induces the decrease of the ignition delay time of DME/propane blends.

关键词： Ethers

来源：评论

学校读者我要写书评

暂无评论

A study of auto-ignition of H2/CO/O2/Ar mixtures at elevated pressure and moderate temperature using shock tube

A study of auto-ignition of H2/CO/O2/Ar mixtures at elevated...

引用

9th Asia-Pacific Conference on Combustion, ASPACC 2013

作者： Thi, Luong Dinh Zhang, Yingjia Fu, Jin Huang, Zuohua State Key Laboratory of Multiphase Flow in Power Engineering Xi'an Jiaotong University No.28 Xianning West Road Xi'an Shaanxi710049 China

Ignition delays of stoichiometric syngas mixtures (H2/CO/O 2) diluted with argon were measured behind the reflected shock wave at pressures of 0.2, 1.0 and 2.0 MPa, temperature from 896 to 1264 K, equivalence ratios of 0.3, 1.0 and 1.5. The effect of non-ideal conditions on ignition delays, determined by pressure trace behind the reflected shock wave (pressure rise rate is approximately 4.22%/ms), was used to calculate. Six available mechanisms were selected to simulate the ignition delays of syngas mixtures, the predicted results were compared with the measured ones. These results indicated that there is no mechanism can calculate accurately ignition delays over all testing conditions. The ignition delays predicted with three mechanisms (Davis 2005, USC ver 2.0, NUI nc5-49) are close to the measured ones. Using the Davis mechanism to analyse reaction kinetics, the achieved results showed that the reaction R1 dominates the ignition process of syngas. The reaction R31 plays an important promoted role in ignition process of syngas mixtures.

关键词： Shock tubes

来源：评论

学校读者我要写书评

暂无评论

Simulation of a solar tower thermal power plant using TRNSYS

Simulation of a solar tower thermal power plant using TRNSYS

引用

26th International Conference on Efficiency, Cost, Optimization, Simulation and Environmental Impact of Energy Systems, ECOS 2013

作者： Yang, Yan Zhang, Fan Cao, Fei Zhao, Liang Guo, Liejin State Key Laboratory of Multiphase Flow in Power Engineering Xi'an Jiaotong University Xi'an China Shanghai Electric Power Generation Group Co. Ltd. Shanghai China

The solar tower thermal power technology is a method to achieve the large-scale utilization of solar energy. A user defined TYPE of the heat receiver for the solar tower thermal power plant (STTPP) is established in the TRNSYS program with Fortran codes. Full-year simulation of the STTPP is investigated based on different input parameters, weather conditions and plant control strategies by taking Beijing as a case study. Through this case, the influences of the receiver diameter, flow form and inlet/outlet temperature on the thermal efficiency, total pump power, power efficiency and 'solar-thermal-electricity' transfer efficiency are studied. Simulation results show that the thermal efficiency of receiver rises with the decrease of pipe diameter. The lower the inlet temperature is;the lower the annual pump power consumption is, and the higher the power efficiency would be. An instantaneous increase of the receiver outlet temperature would reduce the power efficiency. The plant control strategies suggest that the "south-in-north-out" arrangement of the heat receiver working fluid holds the highest power efficiency but lowest annual pump power consumption. The annual power generation increases effectively by introducing the hot and cold molten salt storage tanks. The annual power efficiency increases with the power plant capacity.

关键词： Electric power utilization

来源：评论

学校读者我要写书评

暂无评论

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

请选择保存的检索档案：

请选择收藏分类：

通借通还

建议与咨询 留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

请选择保存的检索档案： 新增检索档案 确定 取消

请选择收藏分类： 新增自定义分类 确定 取消

通借通还

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

请选择保存的检索档案：

请选择收藏分类：