检索结果-内蒙古大学图书馆

Pore Scale Characterization of Gas–Water flow in Heterogeneous Layered Sandstone

Energy & Fuels 2023年第24期37卷 19538-19547页

作者： Yongfei Yang Weichen Sun Hai Sun Lei Zhang Junjie Zhong Kai Zhang Jun Yao National Key Laboratory of Deep Oil and Gas China University of Petroleum (East China) Qingdao 266580 P. R. China Research Center of Multiphase Flow in Porous Media School of Petroleum Engineering China University of Petroleum (East China) Qingdao 266580 P. R. China

The existence of beddings and abundant interlayers in sandstone reservoirs severely hinders the exploration and extraction of sandstone gas reservoir resources. In this study, layered heterogeneous sandstone cores were constructed to explore the impact of sandstone layered heterogeneity on gas–water flow, and the gas–water displacement process was imaged by using X-ray tomography. The changes in the fluid distribution were studied with the help of imaging data. After displacement began, under the influence of heterogeneity, fluid entered the dominating channel made up of big pores preferentially, which had a poor displacement effect in the low permeability layer. In the low permeability layer, a large amount of residual gas was stranded downstream in dead-end corners because there were no efficient seepage channels. Using the residual gas’s shape and distribution properties, three categories─network, multiple, and singlet─were divided. The results show that, with the succession, the large-volume connected network residual gas dominant in pore space was dispersed into smaller multiple residual gas; due to poor connection, the initial percentage of the network residual gas in the low permeability layer of the core was lower than the initial percentage of the network residual gas in the high permeability layer, and the extent of the network residual gas’ dispersion was also less than in the core’s high permeability layer; after increasing back pressure, due to the difficulty in retaining multiple residual gas in the core’s high permeability layer, in comparison to the core’s low permeability layer, the core’s high permeability layer had a larger fraction of singlet residual gas. Only multiple and singlet residual gas remained in the pore space. This study offers fundamental knowledge for the investigation of the gas–water flow law in heterogeneous sandstone, which may help to further enhance the gas reservoir recovery in heterogeneous sandstone.

关键词： Cluster chemistry Fluids Layers Permeability Water

来源：评论

学校读者我要写书评

暂无评论

Steady-State Multi-Physics Coupling Analysis of Heat Pipe Cooled Reactor Core

SSRN

引用

SSRN 2022年

作者： Zhang, Zhipeng Wang, Chenglong Guo, Kailun Tian, Wenxi Qiu, Suizheng Su, Guanghui Department of Nuclear Science and Technology Shaanxi Key Lab. of Advanced Nuclear Energy and Technology Xi’an Jiaotong University Shaanxi Xi’an710049 China State Key Laboratory of Multiphase Flow in Power Engineering China

Due to the advantages of mobility, safety and universality, the heat pipe reactors have great competitiveness in many applications such as strategic defense locations, remote communities, and emergency locations. In addition, most of the heat pipe reactors are designed as solid-state reactors, which avoid the two-phase flow problem caused by the coolant transformation and make it possible to analyze the reactor with multiple physical field coupling. In this work, a typical heat pipe reactor has been carried out a 3-D neutronic-thermal-mechanical analysis, and steady state analysis is performed by OpenMC coupled with COMSOL. Coupling calculation results show that under normal operation, the maximum temperature and thermal expansion of core is 1338.94 K and 2.53 mm. In the steady-state coupling process, the influence of temperature parameters on physical calculation is mainly reflected in k eff and its power level, the maximum temperature drops from 1347.26 K to 1338.94 K, but it has little influence on power distribution. By coupling calculations, the maximum stress of the reactor is reduced by 5.78 MPa. The research results will support the subsequent development of multi-physics coupled transient analysis code for heat pipe reactors. © 2022, The Authors. All rights reserved.

关键词： Heat pipes

来源：评论

学校读者我要写书评

暂无评论

Experimental study on mercury content in flue gas of coal-fired units based on laser-induced breakdown spectroscopy

引用

Plasma Science and Technology 2020年第7期22卷 75-82页

作者： Kai RONG Zhenzhen WANG Ruomu HU Renwei LIU Yoshihiro DEGUCH Junjie YAN Jiping LIU State Key Laboratory of Multiphase Flow in Power Engineering Xi'an Jiaotong UniversityXi'an 710049People’s Republic of China Graduate School of Technology Industrial and Social SciencesTokushima UniversityTokushima 770-8501Japan Moe Key Laboratory of Thermo-Fluid Science and Engineering Xi'an Jiaotong UniversityXi'an 710049People’s Republic of China

Accurate measurement of trace heavy metal mercury(Hg) in flue gas of coal-fired units is great significance for ecological and environmental *** gas was used to simulate the actual flue gas of a power plant in this study.A laser-induced breakdown spectroscopy(LIBS)system for Hg measurement in mixed gas was built to study the effect of mixed gas pressure,Hg concentration in mixed gas and delay time on Hg *** experimental results show that the appropriate low mixed gas pressure can obtain high Hg signal intensity and signal to noise *** Hg signal intensity and signal to noise ratio increased with the increase of Hg concentration in mixed *** Hg signal intensity and signal to noise ratio decreased with the increase in delay *** to the above results,the optimized measurement conditions can be *** Hg concentrations in mixed gas were quantitatively analyzed by the internal standard method and traditional calibration method *** relative error of prediction of the test sample obtained by the internal standard method was within 11.11%.The relative error of prediction of the traditional calibration method was less than 14.54%.This proved that the internal standard method can improve the accuracy of quantitative analysis of Hg concentration in flue gas using LIBS.

关键词： laser-induced breakdown spectroscopy flue gas trace heavy metal quantitative analysis

来源：评论

学校读者我要写书评

暂无评论

Design and Optimal Thermal Efficiency Contrastive Analysis on Closed Brayton Cycle Systems with Different Fluids of Fluoride-Salt-Cooled High-Temperature Advanced Reactor

SSRN

引用

SSRN 2022年

作者： Li, Xinyu Zhang, Dalin Yun, Shichang Zhou, Xingguang Jiang, Dianqiang Lv, Xindi Feng, Zhenyu Wu, Wenqiang Tian, Wenxi Qiu, Suizheng Su, Guanghui Zhao, Quanbin Liu, Xiuting State Key Laboratory of Multiphase Flow in Power Engineering Shaanxi Key Laboratory of Advanced Nuclear Energy and Technology School of Nuclear Science and Technology Xi’an Jiaotong University Xi’an710049 China CNNC Key Laboratory on Nuclear Reactor Thermal Hydraulics Technology Nuclear Power Institute of China Chengdu610213 China

To match the advantages of Fluoride-Salt-cooled high-Temperature Advanced Reactor, the closed Brayton cycle system was selected as the energy conversion system, and the thermodynamic analysis, conjugate gradient optimization, and exergy analysis were performed. The pinch point constraint method based on simultaneous equations was proposed to improve the calculation efficiency and ensure the unity of comparison standards, and the exergy analysis was used to quantify and optimize the exergy losses for the equipment. For the simple regenerative cycle configuration, the thermal efficiency and mass flow rate of the cycle system with various fluids (far-critical fluids: air, nitrogen, helium, and argon, near-critical fluids: carbon dioxide, sulfur hexafluoride, propane, and xenon) were analyzed. The results of the thermodynamic analysis show that the thermal efficiency of the sulfur hexafluoride cycle is the highest and reaching 46.6% with the simple regenerative cycle configuration. The thermal efficiency of the far-critical fluid cycle is more sensitive to turbine efficiency. The results of the exergy analysis show the CO2 cycle has the highest potential to improve thermal efficiency, which has the highest improvement from 43.48% to 49.31% with the recompression process. The method and conclusion of this paper can provide references for the design and optimization of the Brayton power cycle system © 2022, The Authors. All rights reserved.

关键词： Carbon dioxide

来源：评论

学校读者我要写书评

暂无评论

Design and Optimal Thermal Efficiency Analysis on Closed Brayton Cycle System of Fluoride-Salt-Cooled High-Temperature Advanced Reactor (Fustar)

SSRN

引用

SSRN 2022年

作者： Li, Xinyu Zhang, Dalin Yun, Shichang Zhou, Xingguang Jiang, Dianqiang Lv, Xindi Feng, Zhenyu Wu, Wenqiang Tian, Wenxi Qiu, Suizheng Su, G.H. Zhao, Quanbin Liu, Xiuting State Key Laboratory of Multiphase Flow in Power Engineering Shaanxi Key Laboratory of Advanced Nuclear Energy and Technology School of Nuclear Science and Technology Xi’an Jiaotong University Xi’an710049 China CNNC Key Laboratory on Nuclear Reactor Thermal Hydraulics Technology Nuclear Power Institute of China Chengdu610213 China

To match the advantages of Fluoride-Salt-cooled high-Temperature Advanced Reactor (FuSTAR): the high temperature, inherent safety, compact structure, and modularization, the closed Brayton cycle system was selected as the energy conversion system, and the enthalpy analysis, conjugate gradient optimization, and exergy analysis were performed. The pinch point constraint method based on simultaneous equations was proposed to improve the calculation efficiency and ensure the unity of comparison standards, and the exergy analysis was used to quantify and optimize the exergy losses for the equipment. For the simple regenerative cycle configuration, the thermal efficiency and mass flow rate of the cycle system with various fluids (far-critical fluids: air, nitrogen, helium, and argon, near-critical fluids: carbon dioxide, sulfur hexafluoride, propane, and xenon) were analyzed, at the highest thermal efficiencies. The results of enthalpy analysis show that the thermal efficiency of the sulfur hexafluoride cycle is the highest with the simple regenerative cycle configuration. The thermal efficiency of the far-critical fluid cycle is more sensitive to turbine efficiency. The exergy analysis shows the CO2 cycle has the highest potential to improve thermal efficiency. The method and conclusion of this paper can provide references for the design and optimization of the Brayton power cycle system. © 2022, The Authors. All rights reserved.

关键词： Enthalpy

来源：评论

学校读者我要写书评

暂无评论

Thermal Modulation of Radiation Fields Enhancing the Adaptability of Cpv-Hydrogen Systems to Hot Outdoor Conditions

SSRN

引用

SSRN 2023年

作者： Zhu, Yizhou Zhang, Ting’an Geng, Jiafeng Jing, Dengwei Xi'an University of Science and Technology China Department of Chemical Engineering School of Water and Environment Chang'an University Shaanxi Xi’an710064 China International Research Center for Renewable Energy State Key Laboratory of Multiphase Flow in Power Engineering Xi’an Jiaotong University Shaanxi Xi’an710049 China

The efficiency of photovoltaic (PV) modules operating outdoors often subject to significant decrease due to high PV surface temperature under hot outdoor conditions despite of the high irradiation in this period. Meanwhile, the commercial electrolytic water splitting unit requires additional heat sources to preheat the electrolyte, which is neither economical nor energy efficient. This study introduces a proton exchange membrane (PEM) water electrolyzer system coupled with concentrated photovoltaic (CPV) and a pipe-based liquid spectral beam splitting filter acting also as an electrolyte preheater. The results of continuous experiments during local summer daytime show that the average PV surface temperature of the proposed system can be reduced by 23.5 K compared to that without spectral beam splitting filter. Moreover, the average efficiencies of photovoltaic, electrolysis and solar-to-hydrogen can be increased by 7.5%, 8.1% and 5.2%, respectively. Both simulation and experimental results confirm that our design can reduce the sensitivity of system efficiency toward weather factors, especially high-intensity summer irradiation. This work provides a promising option for application of large-scale solar hydrogen production in regions with sufficient sunlight while high outdoor temperature. © 2023, The Authors. All rights reserved.

关键词： Hydrogen production

来源：评论

学校读者我要写书评

暂无评论

Study on Sewage Sludge Drying System with Built-in Solar Drying Bed 3

Study on Sewage Sludge Drying System with Built-in Solar Dry...

引用

3rd International Symposium on Architecture Research Frontiers and Ecological Environment, ARFEE 2020

作者： Gu, Zhipan Yang, Jichun Liu, Jing Tao, Leren Zhang, Ye Huang, Lihao Instiute of Refrigeration and Cryogenics School of Energy and Power University of Shanghai for Science and Technology Shanghai200093 China School of Architecture and Civil Engineering Jiaxing University Jiaxing Zhejiang314001 China Shanghai Key Laboratory of Multiphase Flow and Heat Transfer in Power Engineering University of Shanghai for Science and Technology Shanghai200093 China

In this paper, the renewable energy solar energy is used as the heat source. The combination of solar drying bed and traditional hot air drying can effectively reduce energy consumption and operation cost. The drying chamber is divided into three layers. The top air supply outlet supplies hot air, the middle layer places wet sludge, and the bottom layer uses hot water coil to dry the sludge. The whole drying process is a heat and mass transfer process with convective heat transfer and radiation heat transfer. After analysis and comparison with traditional energy drying, it is found that drying 97.5kg of sewage sludge will save 79% energy, save 12.84 kg of standard coal, reduce 32 kg of carbon dioxide and 1.284 kg of sulphur dioxide. © The Authors, published by EDP Sciences, 2021.

关键词： Drying

来源：评论

学校读者我要写书评

暂无评论

flow Fluctuations and flow Friction Characteristics of Lead-Bismuth Eutectic in a Vertical Tube Under Rolling Conditions

SSRN

引用

SSRN 2022年

作者： Liu, Zhipeng Zhao, Yafeng Tian, Wenxi Wang, Chenglong Qiu, Suizheng Su, Guanghui H. School of Nuclear Science and Technology Shaanxi Key Lab. of Advanced Nuclear Energy and Technology Xi’an Jiaotong University Shaanxi Xi’an710049 China State Key Laboratory of Multiphase Flow in Power Engineering China

The effects of rolling motion on the flow characteristics of lead-bismuth eutectic in a vertical circular tube are investigated experimentally. The results show that the pressure drop and flow rate of the forced LBE circulation fluctuate under rolling conditions. The effect of rolling motion on the flow characteristics decreases with the increase of the corresponding static Reynolds number. The rolling motion may increase the time-averaged frictional resistance coefficient of the LBE when flow rate is low. The critical value of the impact Reynolds number is about 125,000. As a result, the time-averaged flow rate decreases. The analysis shows that it is mainly the transverse additional force caused by the rolling motion increases the frictional resistance of the LBE. An empirical correlation is established to predict the frictional resistance coefficient under rolling conditions. This study may be useful in the thermal-hydraulic analysis of LBE as a working fluid under moving conditions. © 2022, The Authors. All rights reserved.

关键词： Reynolds number

来源：评论

学校读者我要写书评

暂无评论

Recent advances in all-in-one flexible supercapacitors

引用

Science China Materials 2021年第1期64卷 27-45页

作者： Tiezhu Guo Di Zhou Wenfeng Liu Jinzhan Su Electronic Materials Research Laboratory Key Laboratory of the Ministry of Education&International Center for Dielectric ResearchSchool of Electronic Science and EngineeringXi’an Jiaotong UniversityXi’an710049China State Key Laboratory of Electrical Insulation and Power Equipment Xi’an Jiaotong UniversityXi’an710049China International Research Centre for Renewable Energy State Key Laboratory of Multiphase Flow in Power EngineeringXi’an Jiaotong UniversityXi’an710049China

The rise of personalized flexible electronics has promoted the rapid development of flexible supercapacitors due to their long service life,fast charging-discharging rates and safe *** from the traditional flexible supercapacitors,the all-in-one integrated flexible supercapacitors are more resistant to deformation and lower interface resistance,which have a broader application prospect in the field of flexible *** review briefly summarizes the preparation methods and electrochemical properties of some typical all-in-one supercapacitors,represented by planar and fibrous structures in recent ***,the basic understanding of traditional flexible supercapacitors and all-in-one integrated flexible supercapacitors,and the key parameters of the performance of flexible supercapacitors are ***,the hydrogel matrix all-in-one supercapacitors with different functional characteristics(stretchable,self-healing and compressible)and the nonhydrogel matrix(separator,flexible membrane)all-in-one supercapacitors are ***,the challenges and future development of flexible supercapacitors are considered.

关键词： flexible supercapacitors all-in-one hydrogel

来源：评论

学校读者我要写书评

暂无评论

Characterization of fluidization instability in the initial development stage of dense powder pneumatic conveying

引用

Physics of Fluids 2025年第5期37卷

作者： Yang, Shifan Gao, Shilin Zhao, Kunpeng Zhang, Haibin Bai, Bofeng State Key Laboratory of Multiphase Flow in Power Engineering School of Chemical Engineering and Technology Xi'an Jiaotong University Xi'an710049 China

The startup characteristics of powder fuel conveyance significantly impact the reliable ignition of powder-fueled ramjet engines. By utilizing coupled computational fluid dynamics-discrete element method, this study took into full consideration the piston follow-up behavior, the interactions between solid particles and gas flow, as well as wall surfaces, and provided a more accurate analysis of the unsteady features during the initial development stage of dense powder conveying. The results show that the center-internal inlet exhibits superior powder conveying performance compared to that of the tangential-external and reverse-external inlets. While increasing fluidization pressure reduces conveying efficiency, it accelerates the stabilization process. Reducing the wall friction coefficient enhances the startup fluctuation, and pre-filling the powder chamber with gas decreases the piston delay and prevents the sudden drop in powder mass flow rate. This study advances the understanding of the two-phase flow mechanisms in the powder supply system and provides a valuable foundation for optimizing structural designs and operational parameters. © 2025 Author(s).

关键词： flow of gases

来源：评论

学校读者我要写书评

暂无评论

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

请选择保存的检索档案：

请选择收藏分类：

通借通还

建议与咨询 留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

请选择保存的检索档案： 新增检索档案 确定 取消

请选择收藏分类： 新增自定义分类 确定 取消

通借通还

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

请选择保存的检索档案：

请选择收藏分类：