检索结果-内蒙古大学图书馆

SSRN 2024年

作者： Sultana, Maria Karmakar, Subrata Haque, Ariful Ingram School of Engineering Texas State University San MarcosTX78666 United States Materials Science Engineering & Commercialization Program Texas State University San MarcosTX78666 United States

Diamond has been one of the most investigated ultrawide bandgap (UWBG) semiconductors for optoelectronics, superconductors, energy, and quantum applications for almost half of a century owing to its unique properties. Diamonds' intrinsic features- a large bandgap (5.47 eV), an extremely high breakdown voltage (10 MV/cm), the highest thermal conductivity (2200 W/m-K), and very high radiation-tolerance, make them promising for high-power, high-frequency devices suitable for high-temperature and extreme radiation environments. Since the demand for high-speed consumer electronics with large power and faster data handling capacity is rising at an unprecedented rate in the post-COVID era, diamonds' excellent mobility of electrons and holes (4500 and 3800 cm2/V-s) make them ideal for servers and systems. To materialize these multipurpose devices with higher efficiency and endurance than Si and SiC-based technologies, diamonds with good p- and n-type conductivity are needed. Therefore, nearly several decades-long efforts have been devoted to understanding and controlling the carrier conductivities in diamonds. Furthermore, diamonds' color centers' remarkable application as the qubit for next-generation quantum computers has also sparked interest in investigating diamond point defects at the quantum level. Hence, it is necessary to comprehensively study the fabrication, doping, and applications in semiconducting and quantum devices to stay relevant to the diamond revolution and thus advance this flourishing field. Therefore, this review article summarizes the current status and breakthroughs in diamond doping and devices fabricated using doped diamonds to provide an overview of the challenges and successes in using this highly promising UWBG material in electronic, superconducting, and quantum applications. © 2024, The Authors. All rights reserved.

关键词： Diamonds

来源：评论

学校读者我要写书评

暂无评论

An Efficient Surrogate Model of Secondary Electron Formation and Evolution

arXiv

引用

arXiv 2024年

作者： McDevitt, Christopher J. Arnaud, Jonathan Tang, Xian-Zhu Nuclear Engineering Program Department of Materials Science and Engineering University of Florida GainesvilleFL32611 United States Theoretical Division Los Alamos National Laboratory Los AlamosNM87545 United States

This work extends the adjoint-deep learning framework for runaway electron (RE) evolution developed in Ref. [1] to account for large-angle collisions. By incorporating large-angle collisions the framework allows the avalanche of REs to be captured, an essential component to RE dynamics. This extension is accomplished by using a Rosenbluth-Putvinski approximation to estimate the distribution of secondary electrons generated by large-angle collisions. By evolving both the primary and multiple generations of secondary electrons, the present formulation is able to capture both the detailed temporal evolution of a RE population beginning from an arbitrary initial momentum space distribution, along with providing approximations to the saturated growth and decay rates of the RE population. Predictions of the adjoint-deep learning framework are verified against a traditional RE solver, with good agreement present across a broad range of parameters. © 2024, CC BY.

关键词： Electrons

来源：评论

学校读者我要写书评

暂无评论

Electrospun Aligned PCL/Gelatin Scaffolds Mimicking the Skin ECM for Effective Antimicrobial Wound Dressings

引用

Advanced Fiber materials 2023年第1期5卷 235-251页

作者： Erfan Rezvani Ghomi Rajamani Lakshminarayanan Vijila Chellappan Navin Kumar Verma Amutha Chinnappan Rasoul Esmaeely Neisiany Kottaiswamy Amuthavalli Zhi Sheng Poh Brandon Han Siang Wong Nileshkumar Dubey Roger Narayan Seeram Ramakrishna Department of Mechanical Engineering Center for Nanotechnology and SustainabilityNational University of SingaporeSingapore 117581Singapore Ocular Infections and Antimicrobials Research Group Singapore Eye Research InstituteThe Academia20 College RoadDiscovery TowerSingapore 169856Singapore Institute of Materials Research and Engineering(IMRE) Agency for Science Technology and Research(A*STAR)#08‑032 Fusionopolis WayInnovisSingapore 138634Singapore Lee Kong Chian School of Medicine Nanyang Technological University SingaporeClinical Sciences Building11 Mandalay RoadSingapore 308232Singapore Department of Pharmacy National University of Singapore18 Science Drive 4Singapore 117543Singapore Academic Clinical Program in Ophthalmology and Visual Sciences Academic Clinical Program Duke-NUS Medical SchoolSingapore 169857Singapore National Skin Centre 1 Mandalay RoadSingapore 308205Singapore Department of Materials and Polymer Engineering Faculty of EngineeringHakim Sabzevari UniversitySabzevar ***Iran Faculty of Dentistry National University of SingaporeSingapore 119085Singapore ORCHIDS:Oral Care Health Innovations and Designs Singapore National University of SingaporeSingaporeSingapore 119085Singapore Department of Biomedical Engineering University of North Carolina at Chapel HillChapel HillNC 27514USA

Bacterial infections and multidrug-resistant bacteria are major health burdens in wound *** antimicrobial agents,e.g.,ε-polylysine(ε-PL),provide a broad spectrum of antibacterial properties and support dermal cell ***,ε-PL was incorporated into polycaprolactone(PCL)/gelatin electrospun scaffolds collected at varying rotation ***,the samples were crosslinked using dopamine hydrochloride to provide highly proliferative dressings with broad antimicrobial *** morphological study showed that the electrospun wound dressings were smooth,continuous,and bead-free,with a mean diameter ranging from 267±7 to 331±8 nm for all random and aligned *** fiber alignment of the electrospun PCL/gelatin scaffolds improved their tensile strength and ***,nanofiber mats are highly hydro-philic,which is crucial for an efficient wound *** samples also demonstrated high antimicrobial properties against common wound bacterial strains,including methicillin-resistant Staphylococcus aureus(MRSA),Staphylococcus aureus(SA),Escherichia coli(EC),Acinetobacter baumannii(AB),and Pseudomonas aeruginosa(PA).Mammalian cell prolifera-tion and morphology assays involving primary human dermal fibroblasts(hDFs)and immortalized keratinocytes(HaCaT)showed excellent biocompatibility of the electrospun mats and remarkably aligned ***,aligned mats showed more cell migration than randomly oriented mats,which is desirable for more efficient wound ***,it can be concluded that aligned PCL/gelatin mats containingε-PL are promising for potential use in wound dressings.

关键词： Electrospinning Wound healing Fiber alignment Biomaterials Nanofiber dressing Bacterial infections

来源：评论

学校读者我要写书评

暂无评论

A Physics-Informed Deep Learning Description of Knudsen Layer Reactivity Reduction

arXiv

引用

arXiv 2024年

作者： McDevitt, Christopher J. Tang, Xian-Zhu Nuclear Engineering Program Department of Materials Science and Engineering University of Florida GainesvilleFL32611 United States Theoretical Division Los Alamos National Laboratory Los Alamos NM87545 United States

A physics-informed neural network (PINN) is used to evaluate the fast ion distribution in the hot spot of an inertial confinement fusion target. The use of tailored input and output layers to the neural network is shown to enable a PINN to learn the parametric solution to the Vlasov-Fokker-Planck equation in the absence of any synthetic or experimental data. As an explicit demonstration of the approach, the specific problem of Knudsen layer fusion yield reduction is treated. Here, predictions from the Vlasov-Fokker-Planck PINN are used to provide a non-perturbative solution of the fast ion tail in the vicinity of the hot spot thus allowing the spatial profile of the fusion reactivity to be evaluated for a range of collisionalities and hot spot conditions. Excellent agreement is found between the predictions of the Vlasov-Fokker-Planck PINN and results from traditional numerical solvers with respect to both the energy and spatial distribution of fast ions and the fusion reactivity profile demonstrating that the Vlasov-Fokker-Planck PINN provides an accurate and efficient means of determining the impact of Knudsen layer yield reduction across a broad range of plasma conditions. © 2024, CC BY.

关键词： Deep learning

来源：评论

学校读者我要写书评

暂无评论

Lost-Core Injection Molding of Fluidic Elastomer Actuators for the Fabrication of a Modular Eel-Inspired Soft Robot

Lost-Core Injection Molding of Fluidic Elastomer Actuators f...

引用

IEEE International Conference on Soft Robotics (RoboSoft)

作者： Jacobo Cervera-Torralba Yuxiang Kang Eesa M. Khan Iman Adibnazari Michael T. Tolley Department of Mechanical and Aerospace Engineering University of California San Diego (UCSD) La Jolla CA USA Materials Science and Engineering Program University of California San Diego (UCSD) La Jolla CA USA

Biologically inspired soft anguilliform swimming robots show great promise in underwater exploration. Their soft bodies promise to reduce the chance of harming humans or wildlife with which they come into contact, and also to reduce their chance of becoming stuck in complex environments. Furthermore, the efficiency of anguilliform swimming may enable long duration operation. However, the design and fabrication of soft anguilliform swimming robots remain challenging. Here we present a design concept for a modular soft anguilliform robot. To address the challenge of consistently fabricating modules for this design, we also present a new fabrication method that combines injection molding and lost-core molding for the consistent fabrication of bi-directional fluidic elastomer actuator modules. We evaluate the consistency of the fabrication method through visual inspection, weight measurements, bending angle measurements and the measurement of force output of the actuator. This work represents a step towards an autonomous eel-inspired soft robot, as well as a new fabrication approach that may enable a number of other new soft robotic systems.

关键词：

来源：评论

学校读者我要写书评

暂无评论

Correlation between Composition and Work Function Through Kelvin Probe Force Microscopy – Pure Magnesium Single Crystals

SSRN

引用

SSRN 2023年

作者： Türe, Yiğit Kaya, Ali Arslan Shin, Kwang Seon Turan, Servet Eskisehir Technical University Porsuk Vocational School Electronics and Automation Department Program of Mechatronics Eskisehir Turkey Mugla Sıtkı Kocman University Engineering Faculty Metallurgy and Materials Engineering Department Mugla Turkey Seoul National University Materials Science and Engineering Department Seoul Korea Republic of Eskisehir Technical University Engineering Faculty Materials Science and Engineering Department Eskisehir Turkey

The aim of this work was to investigate the feasibility of observing the effect of impurities in pure magnesium (Mg) on the work function (WF) measurements by using Kelvin Probe Force Microscopy (KPFM). In essence, the pure Mg samples used in this study can be regarded as extremely dilute solid solutions of Mg with some impurity atoms. This investigation further considers the measured WF differences within a crystal as figures that are directly affected by the free electron density distribution, which essentially refers to the nature of the interatomic bonding. A corollary of this view is that stacking fault energy (SFE) changes in a solid solution system can also be revealed via KPFM measurements, as SFE also depends on the free electron density distribution. Since the atomic density would affect the WF and SFE levels, the crystal orientations of the single crystal Mg samples had to be determined via electron diffraction patterns obtained via TEM. It has been shown that WF differences as measured via KPFM, offer a technique that can be at least qualitatively correlated with the interatomic bond strength levels, and therefore be also interpreted as an indicator of SFE levels. This practical measurement approach appears to be a reliable way of understanding the effect of individual elemental changes in multi-element solid-solution systems which currently do not lend themselves to computational techniques due to the number of elements involved. It should be borne in mind that the computed SFE values in the literature are not treated as absolute values but rather become useful when assessing the properties of alloys at a fundamental level, i.e., free electron density distributions. Therefore, it seems possible to use the principles of ‘electronic metallurgy’ in developing multi-element alloy systems. © 2023, The Authors. All rights reserved.

关键词： Single crystals

来源：评论

学校读者我要写书评

暂无评论

Flexible organic solar cells for biomedical devices

引用

Nano Research 2021年第9期14卷 2891-2903页

作者： Bin Kan Faheem Ershad Zhoulyu Rao Cunjiang Yu Department of Mechanical Engineering University of HoustonHoustonTX 77204USA Department of Biomedical Engineering University of HoustonHoustonTX 77204USA Materials Science and Engineering Program University of HoustonHoustonTX 77204USA Department of Electrical and Computer Engineering University of HoustonHoustonTX 77204USA Texas Center for Superconductivity University of HoustonHoustonTX 77204USA

Organic solar cells(OSCs),particularly made based on solution processing methods,have made significant progress over the past decades through the concurrent evolution of organic photovoltaic materials and device ***,high power conversion efficiencies around 18%and over 16%have been demonstrated in both rigid and flexible OSCs,*** most of the OSC research has centered on efficiency and cost,their emerging and potential usages in many critical applications,particularly in biomedical fields have been *** this mini-review,we will briefly discuss the high-performance organic photovoltaic materials and the representative flexible OSCs to give a scope on the recent rapid development of ***,we will review some progress on the applications of OSCs in biomedical devices and integrated *** potential challenges associated with integrating OSCs for biomedical devices will be put forward.

关键词： organic solar cells photovoltaic flexible biomedical bioelectronics

来源：评论

学校读者我要写书评

暂无评论

Epitaxial Growth and Characterization of Copper Gallate (CuGa2O4) Thin Films by Pulsed Laser Deposition

SSRN

引用

SSRN 2024年

作者： Emu, Injamamul Hoque Samuels, Brian C. Karmakar, Subrata Hamid, Md. Abdul Shiam, Istiaq Firoz Sarkar, Pallab Kumar Tasnim, Ayesha Haque, Ariful Droopad, Ravi Ingram School of Engineering Texas State University San MarcosTX78666 United States Materials Science Engineering & Commercialization Program Texas State University San MarcosTX78666 United States

High-quality crystalline copper gallate (CuGa2O4) thin films were grown on c-plane sapphire substrates using the pulsed laser deposition (PLD) technique by optimizing the growth parameters (i.e., temperature, oxygen chamber pressure, and laser energy density). The obtained XRD patterns validated that the preferred orientation of the crystalline CuGa2O4 thin film is along the [111] direction, and the crystallinity of the films improved with increasing substrate temperature while maintaining a constant O2 pressure, as assessed by measuring the full width at half maximum (FWHM) of the prominent (222) plane. Reducing the oxygen pressure leads to the emergence of β-Ga2O3 peaks rather than the CuGa2O4 peaks due to the incomplete oxidation of copper (Cu). Subsequent XRD phi (φ) scans revealed a sixfold rotational symmetry of CuGa2O4 and a 30º epitaxial relationship between the film and the sapphire substrate. X-ray photoelectron spectroscopy (XPS) spectra confirmed the presence of Cu1+, Cu2+, and Ga3+ oxidation states in the films. Increasing laser energy density resulted in the complete oxidation of Cu and an increase in the film thickness from 51.8 nm to 183.4 nm. The direct bandgap of CuGa2O4 films was determined to be approximately 4.51±0.01 eV by analyzing the UV-Vis absorbance spectra using the Tauc equation. The refractive index was found to be approximately 2.05±0.01 based on the spectroscopic ellipsometry data. While the impact of increasing laser energy density was negligible on the parameters such as crystal structure, rotational symmetry, oxidation states of gallium (Ga), oxygen (O), bandgap, and refractive index of CuGa2O4 thin film, notable alterations in the oxidation state of Cu and film thickness were observed. © 2024, The Authors. All rights reserved.

关键词： Thin films

来源：评论

学校读者我要写书评

暂无评论

Complex RNA-DNA hybrid nanoshapes from iterative mix-andmatch screening

引用

Nano Research 2021年第1期14卷 46-51页

作者： Shi Chen Zhiyuan Zhang Eugene Alforque Thomas Hermann Department of Chemistry and Biochemistry University of CaliforniaSan DiegoCA 92093USA Center for Drug Discovery Innovation University of CaliforniaSan DiegoCA 92093USA Materials Science and Engineering Program University of CaliforniaSan DiegoCA 92093USA

Hybrid nucleic acid nanostructures partition architectural and functional roles between ribonucleic acid(RNA)joints and deoxyribonucleic acid(DNA)*** self-assemble from nucleic acid modules through synergistic stabilization of marginally stable base pairing interactions within circularly closed ***,we report the development of hybrid nanoshapes that include multiple different RNA modules such as internal loop and three-way junction(3WJ)*** iterative mix-and-match screening approach was used to identify suitable DNA connectors that furnished stable nanoshapes for combinations of different RNA *** resulting complex multicomponent RNA-DNA hybrid nanoshapes were characterized by atomic force microscopy(AFM)*** research provides proof of concept for modular design,assembly and screening of RNA-DNA hybrid nanoshapes as building blocks for complex extended nucleic acid materials with features at the sub-10 nm scale.

关键词： nucleic acid nanotechnology nanoshapes ribonucleic acid(RNA)three-way junction(3WJ) RNA deoxyribonucleic acid(DNA) sub-10 nm features

来源：评论

学校读者我要写书评

暂无评论

Local step-flow dynamics in thin film growth with desorption

引用

Physical Review materials 2024年第3期8卷 033403-033403页

作者： Xiaozhi Zhang Jeffrey G. Ulbrandt Peco Myint Andrei Fluerasu Lutz Wiegart Yugang Zhang Christie Nelson Karl F. Ludwig Randall L. Headrick Department of Physics and Materials Science Program University of Vermont Burlington Vermont 05405 USA Division of Materials Science and Engineering Boston University Boston Massachusetts 02215 USA X-ray Science Division Argonne National Laboratory Lemont Illinois 60439 USA National Synchrotron Light Source II Brookhaven National Lab Upton New York 11973 USA Department of Physics Boston University Boston Massachusetts 02215 USA

Desorption of deposited species plays a role in determining the evolution of surface morphology during crystal growth when the desorption time constant is short compared with the time to diffuse to a defect site, step edge, or kink. However, experiments to directly test the predictions of these effects are lacking. Novel techniques such as in situ coherent x-ray scattering can provide significant new information. Herein we present x-ray photon correlation spectroscopy (XPCS) measurements during diindenoperylene (DIP) vapor deposition on thermally oxidized silicon surfaces. DIP forms a nearly complete two-dimensional first layer over the range of temperatures studied (40–120∘C), followed by mounded growth during subsequent deposition. Local step flow within mounds was observed, and we find that there was a terrace-length-dependent behavior of the step edge dynamics. This led to unstable growth with rapid roughening (β>0.5) and deviation from a symmetric error-function-like height profile. At high temperatures, the grooves between the mounds tend to close up leading to nearly flat polycrystalline films. Numerical analysis based on a (1+1)-dimensional model suggests that terrace-length dependent desorption of deposited ad-molecules is an essential cause of the step dynamics, and it influences the morphology evolution.

关键词： Growth Surface diffusion Surface instabilities Atomic force microscopy Surface scattering X-ray techniques

来源：评论

学校读者我要写书评

暂无评论

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

请选择保存的检索档案：

请选择收藏分类：

通借通还

建议与咨询 留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

请选择保存的检索档案： 新增检索档案 确定 取消

请选择收藏分类： 新增自定义分类 确定 取消

通借通还

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

请选择保存的检索档案：

请选择收藏分类：