检索结果-内蒙古大学图书馆

Investigation of Tamarind Seed Oil biodiesel with aluminium oxide nanoparticle in CI engine

materials Today: Proceedings 2021年 37卷 1417-1421页

作者： V.S. Shaisundaram M. Chandrasekaran R. Muraliraja Mohanraj Shanmugam S. Baskar Arun Bhuvendran Department of Automobile Engineering Vels Institute of Science Technology and Advanced Studies Chennai India Department of Mechanical Engineering Vels Institute of Science Technology and Advanced Studies Chennai India Department of Materials Engineering and Nanotechnology Politecnico di Milano Milano Italy Department of Automobile Engineering Kumaraguru College of TechnologyCoimbatore India

Because of increasing automobiles, power plants and factories, increasing of this automobiles, power plants produce the more emissions like CO, HC and NOx. So that the world is searching for the alternative fuel, which will not create any harm to the environment and also it would be less in cost. Biodiesel is one of the main solutions to the global energy crisis. In this present work studied the performances and emission characteristics of Tamarind Seed Oil Bio-diesel (TSO). Use of additives for better combustion characteristics to the biodiesel. The blends of Tamarind Seed oil (TSO) with the additives Aluminum oxide (Al 2 O 3 ) are B10 + 20 PPM Al 2 O 3 , B20 + 20PPM Al 2 O 3 , B30 + 20 PPM Al 2 O 3 . This blends were analyzed and their performance and emissions characteristics compared with performance and emission characteristics of diesel. Tests were carried out over entire range of engine operation at varying conditions of load. The engine exhaust gas emissions are reduced with increase biodiesel concentration.

关键词：

来源：评论

学校读者我要写书评

暂无评论

Waste Valorization from Brazilian Nepheline Syenite Processing as a Strategic Approach to Advancing the Circular Economy

SSRN

引用

SSRN 2023年

作者： Santos, Diego Haltiery Rosa, Laura Pereira Alves, Cleidson Rosa Simão, Lisandro Arcaro, Sabrina Klegues Montedo, Oscar Rubem Raupp-Pereira, Fabiano Graduate Program in Materials Science and Engineering University of the Extreme South of Santa Catarina Criciúma88806-000 Brazil Department of Civil Engineering Federal Institute of Santa Catarina Criciúma88813-600 Brazil Research Group on Sustainability and Waste Management Postgraduate Program in Environmental Technology University of Ribeirão Preto Ribeirão Preto14096-900 Brazil Brazil

The growing disparity between the high extraction of natural resources and low use of waste as alternative mineral resources will aggravate the scarcity of natural reserves. Therefore, the current linear economy model must be converted to sustainable economic models, such as the circular economy. To achieve this transition, it is important that waste recovery strategies are implemented with a continuous search for solutions for these materials. Thus, this study investigates the waste from the processing of nepheline syenite stone, to promote its valorization as an alternative mineral resource. The classification, potentiality, quantity/viability and applicability (CPQvA) criteria are used as tools to aid decision-making for the waste valorization. The environmental, physical, chemical, morphological, and durability characteristics of nepheline syenite waste (NSW) are analyzed. The results showed evidence for the substitution of NSW for up to 100% of fine aggregates and 25% of Portland cement in civil construction. Furthermore, NSW yields recoveries of more than 90% of potassium for use in agriculture, and up to 70% of iron ore for use in steelworks. Therefore, the results indicate that NSW is viable for different applications, contributing to industrial symbiosis and a strategy for advancing the circular economy. © 2023, The Authors. All rights reserved.

关键词： Sustainable development

来源：评论

学校读者我要写书评

暂无评论

An unprecedented synergy of high-temperature tensile strength and ductility in a NiCoCrAlTi high-entropy alloy

arXiv

引用

arXiv 2023年

作者： Zhang, Hongmin Meng, Fanchao Meng, Haoyan Tong, Yang Liaw, Peter K. Yang, Xiao Zhao, Lei Wang, Haizhou Gao, Yanfei Chen, Shuying Institute for Advanced Studies in Precision Materials Yantai University Shandong Yantai264005 China Department of Materials Science and Engineering The University of Tennessee KnoxvilleTN37996 United States Key Laboratory of Cryogenics Technical Institute of Physics and Chemistry Chinese Academy of Sciences Beijing100190 China Beijing Advanced Innovation Center for Materials Genome Engineering Beijing Key Laboratory of Metal Materials Characterization Central Iron and Steel Research Institute Beijing100081 China

The present work reported a novel L12-strengthening NiCoCrAlTi high entropy alloy (HEA) with an outstanding synergy of tensile strength and ductility at both ambient and high temperatures. Transmission electron microscopy (TEM) characterization revealed a high density of rod-like and spheroidal L12 precipitates distributing in the micro/nanograins and non-recrystallized regions in the annealed specimens. The tremendously high yield stress, ultimate tensile stress (UTS), and ductility of the HEA at 600 °C were ~1060 MPa, 1271 MPa, and 25%, respectively, which were significantly superior to most reported HEAs and Co- and Ni-based superalloys to date. Systematic TEM analysis unveiled that the cooperation among L12 precipitation, extensive stacking faults (SFs), deformation twins (DTs), immobile Lomer-Cottrell (L-C) locks formed from interactions between SFs and SFs/DTs, hierarchical SFs/DTs networks, as well as hetero-deformation-induced strengthening dominated the plastic deformation at 600 °C. Such a unique deformation mechanism enabled extremely high tensile strength and sustained ductility of the HEA at a high temperature. © 2023, CC BY-NC-ND.

关键词： Stacking faults

来源：评论

学校读者我要写书评

暂无评论

Nanoslot-Induced Ultrastrong Phonon-Photon and Phonon-Phonon Coupling in Hybrid Organic-Inorganic Perovskites 16

Nanoslot-Induced Ultrastrong Phonon-Photon and Phonon-Phonon...

引用

16th Pacific Rim Conference on Lasers and Electro-Optics, CLEO-PR 2024

作者： Kim, Dasom Hou, Jin Lee, Geon Agrawal, Ayush Kim, Sunghwan Zhang, Hao Bao, Di Baydin, Andrey Wu, Wenjing Tay, Fuyang Huang, Shengxi Hagenmüller, Daivd Chia, Elbert E. M. Kim, Dai-Sik Seo, Minah Mohite, Aditya D. Kono, Junichiro Applied Physics Graduate Program Smalley-Curl Institute Rice University HoustonTX77005 United States Department of Electrical and Computer Engineering Rice University HoustonTX77005 United States Department of Materials Science and NanoEngineering Rice University HoustonTX77005 United States Sensor System Research Center Korea Institute of Science and Technology Seoul02792 Korea Republic of Department of Physics and Astronomy Seoul National University Seoul08826 Korea Republic of Department of Chemical and Biomolecular Engineering Rice University HoustonTX77005 United States Ulsan44919 Korea Republic of Division of Physics and Applied Physics School of Physical and Mathematical Sciences Nanyang Technological University 637371 Singapore Smalley-Curl Institute Rice University HoustonTX77005 United States Université de Strasbourg Cnrs Strasbourg67000 France KU-KIST Graduate School of Converging Science and Technology Korea University Seoul02841 Korea Republic of Department of Physics and Astronomy Rice University HoustonTX77005 United States

Methods for harnessing vibrational states are desired for phonon-based technologies. We realized ultrastrong coupling of two phonon modes in perovskite materials induced by ultrastrong coupling with a common photonic ... 详细信息

ISBN: (纸本)9798350372076

关键词： Organic-inorganic materials

来源：评论

学校读者我要写书评

暂无评论

Machine learning moment tensor potential for modeling dislocation and fracture in L10−TiAl and D019−Ti3Al alloys

引用

Physical Review materials 2023年第10期7卷 103602-103602页

作者： Ji Qi Z. H. Aitken Qingxiang Pei Anne Marie Z. Tan Yunxing Zuo M. H. Jhon S. S. Quek T. Wen Zhaoxuan Wu Shyue Ping Ong Materials Science and Engineering Program University of California San Diego 9500 Gilman Dr Mail Code 0448 La Jolla California 92093-0448 USA Institute of High Performance Computing (IHPC) Agency for Science Technology and Research (A*STAR) 1 Fusionopolis Way Connexis #16-16 Singapore 138632 Republic of Singapore Department of NanoEngineering University of California San Diego 9500 Gilman Dr Mail Code 0448 La Jolla California 92093-0448 USA Department of Mechanical Engineering The University of Hong Kong Hong Kong SAR China Department of Materials Science and Engineering City University of Hong Kong Hong Kong SAR China Hong Kong Institute for Advanced Study City University of Hong Kong Hong Kong SAR China

Dual-phase γ-TiAl and α2−Ti3Al alloys exhibit high strength and creep resistance at high temperatures. However, they suffer from low tensile ductility and fracture toughness at room temperature. Experimental studies show unusual plastic behavior associated with ordinary and superdislocations, making it necessary to gain a detailed understanding on their core properties in individual phases and at the two-phase interfaces. Unfortunately, extended superdislocation cores are widely dissociated beyond the length scales practical for routine first-principles density-functional theory (DFT) calculations, while extant interatomic potentials are not quantitatively accurate to reveal mechanistic origins of the unusual core-related behavior in either phases. Here, we develop a highly accurate moment tensor potential (MTP) for the binary Ti-Al alloy system using a DFT dataset covering a broad range of intermetallic and solid solution structures. The optimized MTP is rigorously benchmarked against both previous and new DFT calculations, and unlike existing potentials, is shown to possess outstanding accuracy in nearly all tested mechanical properties, including lattice parameters, elastic constants, surface energies, and generalized stacking fault energies (GSFE) in both phases. The utility of the MTP is further demonstrated by producing dislocation core structures largely consistent with expectations from DFT-GSFE and experimental observations. The new MTP opens the path to realistic modeling and simulations of bulk lattice and defect properties relevant to the plastic deformation and fracture processes in γ-TiAl and α2−Ti3Al dual-phase alloys.

关键词： Interatomic & molecular potentials Alloys Machine learning

来源：评论

学校读者我要写书评

暂无评论

The Influence of Nbb Inoculation on Dendritic Spacing and Grain Size of an Aluminum 2017 Alloy at Different Cooling Rates

SSRN

引用

SSRN 2022年

作者： Silva, Argos Soares de Albuquerque Sousa, Sarah Maria de Gouveia, Guilherme Lisboa Garcia, Amauri Spinelli, José Eduardo Department of Materials Engineering Federal University of São Carlos UFSCar SP São Carlos13565-905 Brazil Federal University of São Carlos Graduate Program in Materials Science and Engineering SP São Carlos13565-905 Brazil Department of Manufacturing and Materials Engineering University of Campinas SP Campinas13083-860 Brazil

The Al-4Cu-Mg 2017 alloy is a significant Al extrusion alloy. As a result, knowing its behavior in terms of grain refining during casting stages becomes critical for the next processing steps. In the face of the shortcomings exhibited by TiB inoculants, the addition of NbB could be tested for this alloy as an alternative. The present article investigates the effects of NbB addition on grain size (GS), on secondary dendrite arm spacing (λ2) and on hardness of centrifugally cast (CC) and directionally solidified (DS) 2017 alloy samples, encompassing a broad range of cooling rates and solidification conditions. The λ2 did not change much as a result of the NbB inoculation, either for DS or CC samples, decreasing from 7.2 μm to 7.0 μm in the case of the 4 mm-thick CC samples and increasing from 17.0 μm to 22.5 μm in the case of the DS samples. The average GS, on the other hand, reduced from 293 μm to 136 μm for the NbB-containing CC samples and from 756 μm to 313 μm for the DS samples associated with cooling rates of 10 K/s. Both processes can achieve nearly the same GS reduction ratio, namely 2.2 for the CC and 2.5 for the DS. This implies that GS reduction ratio was barely affected if similar cooling rates were compared while taking the experimental range for both processes into account. Moreover, Vickers hardness results revealed that GS had little influence on this property for both alloys studied. The experimentally obtained data translated a variety of solidification condition outlines for the 2017 alloy. Through this data, understanding of an alternative inoculant in a significant Al alloy series advanced significantly. © 2022, The Authors. All rights reserved.

关键词： Solidification

来源：评论

学校读者我要写书评

暂无评论

Characterization of the Root Surface of a Friction Stir Welded Uns S32760 Super Duplex Stainless Steel: Insights into its Microstructure and Corrosion Resistance

SSRN

引用

SSRN 2023年

作者： Vacchi, G.S. de Carvalho, Willian S. Meinhardt, C.P. Bergmann, Luciano A. Amancio-Filho, Sergio T. Rovere, C.A.D. Munir Rachid Corrosion Laboratory Department of Materials Engineering Federal University of São Carlos Rodovia Washington Luis Km 235 SP São Carlos13565-905 Brazil Federal University of São Carlos Graduate Program in Materials Science and Engineering Brazil Graz University of Technology – TU Graz Institute of Materials Science Joining and Forming BMK Endowed Professorship for Aviation Kopernikusgasse 24/1 Graz8010 Austria Federal University of Pampa Department of Mechanical Engineering Avenida Tiarajú 810 RS Alegrete Brazil Helmholtz-Zentrum Hereon Institute of Materials Mechanics Solid State Materials Processing Max-Planck-Straße 1 Geesthacht Germany

The root surface of a friction stir welded super duplex stainless steel (UNS S32760) was thoroughly characterized in this study. The findings revealed a refined grain structure and a conspicuous increase of 50 HV0.3 in the Root's hardness. Interestingly, the volume fraction of the ferrite phase remained largely unchanged. Rapid cooling in the welding process led to the Cr2N precipitation at the ferrite/ferrite grain boundaries in the root area, significantly increasing sensitization, reducing localized corrosion resistance under high potentials in a neutral pH saline environment, and adversely affecting root passivity in a hydrochloric acid environment compared to the base metal. © 2023, The Authors. All rights reserved.

关键词： Friction stir welding

来源：评论

学校读者我要写书评

暂无评论

Comparison of PM-HIP to Forged SA508 Pressure Vessel Steel Under High-Dose Neutron Irradiation

arXiv

引用

arXiv 2023年

作者： Jiang, Wen Zhao, Yangyang Lu, Yu Wu, Yaqiao Frazer, David Guillen, Donna P. Gandy, David W. Wharry, Janelle P. School of Materials Engineering Purdue University West LafayetteIN United States Micron School of Materials Science & Engineering Boise State University BoiseID United States Center for Advanced Energy Studies Idaho FallsID United States Idaho National Laboratory Idaho FallsID United States Electric Power Research Institute CharlotteNC United States

Powder metallurgy with hot isostatic pressing (PM-HIP) is an advanced manufacturing process that is envisioned to replace forging for heavy nuclear components, including the reactor pressure vessel (RPV). But PM-HIP products must at least demonstrate comparable irradiation tolerance than forgings in order to be qualified for nuclear applications. The objective of this study is to directly compare PM-HIP to forged SA508 Grade 3 Class 1 low-alloy RPV steel at two neutron irradiation conditions: ~0.5-1.0 displacements per atom (dpa) at ~270ºC and ~370ºC. PM-HIP SA508 experiences greater irradiation hardening and embrittlement (total elongation) than forged SA508. However, uniform elongation and approximate toughness are comparable across all irradiated materials, suggesting irradiated PM-HIP SA508 exhibits superior ductility at maximum load-bearing capacity. The irradiation hardening mechanism is linked to composition rather than fabrication method. Since PM-HIP SA508 has higher Mn and Ni concentration, it is more susceptible to irradiation-induced nucleation of Mn-Ni-Si-P (MNSP) nanoprecipitates and dislocation loops, which both contribute to hardening. Conversely, the forged material nucleates fewer MNSPs, causing dislocation loops to control irradiation hardening. These results show promise for the irradiation performance of PM-HIP SA508 and can motivate future nuclear code qualification of PM-HIP fabrication for RPVs. © 2023, CC BY-NC-ND.

关键词： Neutron irradiation

来源：评论

学校读者我要写书评

暂无评论

Effect of dual modification on structural, functional and dielectric properties of cassava starch

Food Physics

引用

Food Physics 2025年 2卷

作者： Cremasco, Paula Figueiredo M. Siqueira, Karine Mayuri Pistoni Sobral, Paulo José do Amaral Velloso, Walter Ferreira de Lima, César Gonçalves Gut, Jorge Andrey Wilhelms Moraes, Izabel Cristina Freitas Postgraduate Program in Materials Science and Engineering Faculty of Animal Science and Food Engineering University of São Paulo Avenue Duque de Caxias Norte São Paulo Pirassununga 13635900 Brazil Department of Biossistems Engineering Faculty of Animal Science and Food Engineering University of São Paulo Avenue Duque de Caxias Norte São Paulo Pirassununga 13635900 Brazil Department of Food Engineering Faculty of Animal Science and Food Engineering University of São Paulo Avenue Duque de Caxias Norte São Paulo Pirassununga 13635900 Brazil Food Research Center (FoRC) University of São Paulo Lake Street São Paulo São Paulo 05508-080 Brazil Departament of Basic Sciences Faculty of Animal Science and Food Engineering University of São Paulo Avenue Duque de Caxias Norte São Paulo Pirassununga 13635900 Brazil Department of Chemical Engineering Polytechnic School University of São Paulo Lake Street São Paulo São Paulo 05508-080 Brazil

The combined effect of hydrocolloid addition and microwave heating on the structural, physical and functional properties of cassava starch remains underexplored, despite individual studies on these modification methods. The dielectric properties, important for the microwave treatment of starch, have received little attention in recent studies. Cassava starch with and without addition of hydrocolloids (guar and xanthan gums) was modified by microwave heating for two different exposure times, and its structural, functional, and dielectric properties were studied. The dual modification enhanced the swelling power and oil holding capacity of the starch, reduced its gelatinization temperature, and did not alter its crystallinity. Notably, xanthan-modified starch microwaved for 6 min exhibited higher color variation (ΔE*) and increased granules agglomeration, while the microwave treatment alone roughened the surface of the starch granules. The mean diameters D[4,3] of starch increased with xanthan gum addition, microwave treatment (6 min), and their combination. The relative permittivity (ε’), loss factor (ε”) and penetration depth (D_p) were lower for samples modified by the combined method. Considering the type of hydrocolloid and the microwave exposure time, the combined modification significantly influenced the properties of starch, offering a promising approach to producing starch with enhanced functional properties. © 2024 KeAi Communications Co., Ltd

关键词： Biopolymers Cassava starch Guar Microwave Xanthan

来源：评论

学校读者我要写书评

暂无评论

Solar desalination: A review of recent developments in environmental, regulatory and economic issues

引用

Solar Compass 2023年 5卷

作者： Goosen, Mattheus Mahmoudi, Hacene Alyousef, Yousef Ghaffour, Noreddine Office of Graduate Studies Research & Innovation Alfaisal University Riyadh Saudi Arabia Faculty of Technology Hassiba Benbouali University of Chlef Algeria Water Desalination & Reuse Center (WDRC) King Abdullah University of Science & Technology (KAUST) Thuwal 23955-6900 Saudi Arabia Environmental Science & Engineering Program Biological & Environmental Science & Engineering (BESE) Division King Abdullah University of Science & Technology (KAUST) Thuwal 23955-6900 Saudi Arabia

The aim of the current study was to provide a review of recent developments in solar desalination from the viewpoint of environmental, regulatory, and economic aspects. The analysis attempted to give better insight into the larger question of why more solar desalination plants are not being established by reviewing different technologies, drivers, barriers, and markets. Critical barriers which were dependent on the level of regional development were found to be uncertainty of government subsidies and a lack of regulatory policies. A new tool called a Pareto frontier may be utilized to generate optimal points in complex scenarios with a high number of variables. This all-inclusive method should be employed in any major decision-making process. Furthermore, in exciting innovative research studies, a sustainable Janus wood evaporator was developed that overcame many of the current solar desalination problems. While subsidies were crucial in the growth of renewable energy programs, barriers in deployment of solar desalination systems still exist such as low electricity tariff structures and fragmented energy policies. The overall trend was towards integration of renewable energy with conventional sources and energy storage systems. © 2023 The Author(s)

关键词： Drivers and barriers Janus wood evaporator Level of development Markets and policies Pareto frontier Sustainability

来源：评论

学校读者我要写书评

暂无评论

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

请选择保存的检索档案：

请选择收藏分类：

通借通还

建议与咨询 留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

请选择保存的检索档案： 新增检索档案 确定 取消

请选择收藏分类： 新增自定义分类 确定 取消

通借通还

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

请选择保存的检索档案：

请选择收藏分类：