检索结果-内蒙古大学图书馆

THE NEW ROAD - ocean AND naval engineering IN THE 1990S

naval ENGINEERS JOURNAL 1991年第1期103卷 75-78页

作者： BALES, SML Susan Bales is the science advisor to the chief of naval operations and the assistant director for science and technology of the CNO Executive Panel. She is on assignment from the Office of Naval Research where she holds the position of assistant director for program support and special programs. Previously she was head of the Ocean Environment Group at David Taylor Research Center. Among her fields of technical expertise are radio-electronic battle management/space and electronic combat naval oceanography coastal dynamics ship engineering hydrodynamics technology wargaming climatology and the Arctic. Since joining the CNO's staff in 1987 Ms. Bales has participated in a number of strategic long-range planning efforts including the 1990 Defense Science Board Summer Study. She has been active in international exchange agreements coordinating the 1987 Labrador Extreme Waves Experiment (LEWEX) and chairing a NATO Research Study Group. She has lectured at the Massachusetts Institute of Technology Webb Institute of Naval Architecture the NATO ASW SACLANT Centre the Admiralty Marine Technology Establishment and the Royal Netherlands Meteorological Institute. Active in a number of professional societies Ms. Bales has served as vice president of the American Society of Naval Engineers (ASNE) and chaired the Naval Engineers Journal Committee. Her research has been published in more than 50 papers articles and reports both here and abroad. She has received the Navy Meritorious Civilian Service Medal was named the 1988 National Capital Senior Engineer of the Year by the D.C. Council of Engineering and Architectural Societies and was elected to membership in the COSMOS Club in 1989. She was married to the late Nathan K. Bales and resides in Myersville Md.

来源：评论

学校读者我要写书评

暂无评论

PROCESS-CONTROL IN A FOREIGN ACQUISITION

引用

naval ENGINEERS JOURNAL 1990年第1期102卷 53-56页

作者： HALPER, ID PRENTICE, GS SELVIDGE, RB Irving D. Halper: attended the City University of New York majoring in mechanical engineering. His career in naval engineering started with various consulting firms prior to his joining the Bureau of Ships in 1963. He is currently the director of the Procurement Appraisal and Logistics Division in the Naval Sea Systems Command's Aircraft Carrier Program Office (PMS 312). George S. Prentice: obtained his B.S. degree in naval architecture from the University of Michigan in 1964. He worked for one and one-half years at Newport News Shipbuilding and Dry Dock before moving to the Naval Sea Systems Command. He is a member of the Society of Naval Architects and Marine Engineers and has written several papers for various organizations and publications. Ronald B. Selvidge: obtained his B.S.M.E. from the University of New Orleans in 1985 at which time he obtained his EIT status. He is an assistant engineering project manager for the Deep Submergence and Ocean Engineering Program Office (PMS 395) of the Naval Sea Systems Command. Professional memberships include the American Society of Mechanical Engineers and the Association of Scientists and Engineers of the Naval Sea Systems Command where he holds the chairmanship of the Legislative Committee.

In 1973, the Boston naval Shipyard was closed. That shipyard's forge shop was the only source, worldwide, for forged (die-lock) aircraft carrier anchor chain. The Navy determined that a domestic manufacturing facility for large size welded chain was being constructed and decided to develop a specification for a welded carrier anchor chain. Cutbacks in the offshore oil industry stopped construction of that plant and the Navy became dependent on foreign sources. The initial procurement of welded aircraft carrier chain invoked society inspection and certification, and until problems were discovered during shipboard installation, was considered satisfactory. A recheck of the chain, with the certification society's participation, revealed that physical dimensions, breaking strength, and metallurgical properties failed to meet specified values. The next buy of new and replacement chain imposed more stringent QA requirements. It was awarded to the same foreign manufacturer on a competitive bid basis. Because of the prior problems with this vendor, the Navy determined that an on-site inspection team was needed to ensure specification compliance. The experiences of that team are described in this paper. The lessons that were learned relative to the manufacturing process, the lack of communication between QA management and production personnel, and the need for close control over specification enforcement are discussed.

关键词： Chains

来源：评论

学校读者我要写书评

暂无评论

BOTTOM BOUNCE ARRAY SONAR SUBMARINE (BBASS)

引用

naval ENGINEERS JOURNAL 1989年第5期101卷 59-72页

作者： JACKSON, HA NEEDHAM, WD SIGMAN, DE USN (RET.) Capt. Harry A. Jackson USN (Ret.) is a graduate of the University of Michigan in naval architecture and marine engineering and completed the General Electric Company's 3-year advanced engineering course in nuclear engineering. He has been an independent consulting engineer and participated in projects involving deep submergence waste disposal water purification and submarine design both commercial and government. Cdr. William D. Needham USN is currently assigned as the repair officer of USS Hunley (AS-31) in Norfolk Virginia. He received a regular commission through NROTC at Duke University where he graduated magna cum laude in mechanical engineering. Selected for the Nuclear Power Program he served as a division officer on the USS Grayling (SSN-646) as the production training assistant at the MARE Prototype Reactor in New York and as blue crew engineer of the USS Nathan Hale (SSBN-623) where he completed the requirements to be designated qualified for command of submarines. Following line transfer to the EDO community in 1981 he completed a tour as nuclear repair officer (Code 310) at Norfolk Naval Shipyard and earned master of science in materials science and ocean engineer's degrees at MIT. His awards include the Meritorius Service Medal Navy Commendation Medal Navy Achievement Medal Spear Foundation Award and the Vice Admiral C.R. Bryan Award. Cdr. Needham also holds a master of arts degree in business management from Central Michigan University. Capt. Jackson was technical director of Scorpion Search Phase II. The on-site investigation included descending over 12 000 feet to the bottom of the ocean. He was also supervisor of one of the Navy's largest peacetime shipbuilding and repair programs. His responsibilities included supervision of design production and contract administration. Capt. Jackson was third from the top in managaement of a major shipyard and responsible for design material procurement work order and financial control of two major surface ship prototypes as well a

Anticipated technological advances in the quieting of potential adversary submarines mandate the use of increasingly effective detection systems for U.S. ASW forces. Based on the assumptions that sonar will continue to be the primary means of detection and that the effectiveness of each individual sonar element will not change markedly, one must increase the projected area of the sonar array to improve its capability. The primary SSN mission of anti-submarine warfare will hence require increasing the hull area devoted to the primary sonar detection system. A revolutionary hull form is proposed that maximizes the area available for this purpose. The advantages and disadvantages of this hull form are discussed and feasibility study level design parameters and arrangements presented.

关键词： Submarines

来源：评论

学校读者我要写书评

暂无评论

AUXILIARY SHIP HULL FORM DESIGN AND RESISTANCE PREDICTION

引用

naval ENGINEERS JOURNAL 1988年第3期100卷 275-292页

作者： FUNG, SC The author is a naval architect with the Preliminary Design Division of the Naval Sea Systems Command. Mr. Fung graduated from National Cheng Kung University in 1976 and Stevens Institute of Technology in 1977 from which he received his B.S. degree in naval architecture and marine engineering and M.S. degree in ocean engineering respectively. He started his career with M. Rosenblatt and Son in 1979 and became a senior naval architect with the Hull Form & Hydrodynamics Department in Designers and Planners in 1981. For the past ten years Mr. Fung has performed a variety of tasks in the area of feasibility study hydrodynamic design including advanced marine vehicles bulbous bows and hull form design for surface combatant and non-combatant ships. Currently he is a project naval architect for the T-AO twin skeg integrated hull design and the AE-36 Energy Enhancement Program. Mr. Fung is a member of ASE ASNE and SNAME. He received the John C. Niedermair A ward in 1984 and 1986 for the best paper presented at the ASE annual technical symposiums.

In this paper 154 auxiliary type monohull designs are analyzed for guidance on how to select the appropriate hull form parameters, particularly with regard to the effects of hull section shapes, sectional area and design waterline curves on ship resistance. This paper also discusses the resistance predictions based on (1) the statistical approach and (2) the use of series model test data (such as Taylor's standard series) and associated “worm curve factors” with the help of data management software.

关键词： SHIPS

来源：评论

学校读者我要写书评

暂无评论

MODERNIZATION OF THE BARQUE EAGLE

引用

naval ENGINEERS JOURNAL 1985年第4期97卷 49-57页

作者： TSAI, NT HACISKI, EC KUCINSKI, JJ Nien-tszr Tsai:is a naval architect with the Hull Section Naval Engineering Division U.S. Coast Guard Headquarters. He received his B.S. and M.S. in mechanical engineering from ChengKung University in Taiwan China and his Ph.D. in mechanical engineering from the University of Rochester in 1969. Prior to joining the Coast Guard in 1982 Mr. Tsai worked at General Dynamics Litton Ship Systems and the David Taylor Naval Ship Research and Development Center in the area of ship dynamics moored and towed ocean systems evaluation and development. He is a member of ASME and ASNE. Eugene C. Haciski:received his B.S. degree in mechanics from the Warsaw University of Technology in 1946 and his M.S. degree in naval architecture from the Polytechnical University of Gdansk Poland in 1950. Prior to joining the U.S. Coast Guard in 1967 he served as a project engineer in the Gdansk Ship Design Center and in the Shipyard Maua in Rio de Janeiro Brazil. After serving 7 years in the U.S. Coast Guard Yard in Curtis Bay Maryland as a supervisory naval architect and 3 years in the Merchant Marine Technical Division USCG he was assigned in 1976 to his current position of chief Hull Section Naval Engineering Division USCG Headquarters. LCDR. Joseph Kucinski:is currently assigned to the Coast Guard Yard as chief quality assurance. He has served in the Yard as ship superintendent and ship superintendent coordinator. Prior to his assignment at the Yard he served as engineer officer aboard USCGC Courageous. He has also served on USCGC Boutwell and as the marine safety officer Duluth Minn. He is a 1973 graduate of Officer Candidate School. LCdr. Kucinski has prior enlisted service in the Navy's nuclear power program.

The U.S. Coast Guard training barque Eagle (WIX-327), former Horst Wessel , was built in 1936, by Blohm & Voss in Germany, for the German Navy and to the rules of Germanischer Lloyd. Since 1946 she has served continuously as the training vessel for the U.S. Coast Guard Academy. To improve safety and performance, an extensive phased modernization was undertaken from 1979 through 1983 at the Coast Guard Yard. Changes in the subdivision, ballast and tankages were made to satisfy the criteria for two-compartment damage stability. Extensive renovation of machinery, structure, navigation components and habitability was also accomplished during the same period. Scheduled summer training cruises were maintainedeach year.

关键词： SAILING VESSELS

来源：评论

学校读者我要写书评

暂无评论

FUTURE PROPULSION MACHINERY TECHNOLOGY FOR GAS-TURBINE POWERED FRIGATES, DESTROYERS, AND CRUISERS

引用

naval ENGINEERS JOURNAL 1984年第2期96卷 34-46页

作者： BASKERVILLE, JE QUANDT, ER DONOVAN, MR USN The Authors Commander James E. Baskerville USNis presently assigned to Naval Sea Systems Command (NA VSEA) as the Ship Design Manager for the DDG 51 the Navy's next generation surface combatant. A graduate of the U.S. Naval Academy Class of 1969 he is a qualified Surface Warfare Officer and designated Engineering Duty Officer (ED). He received his M.S. degree in Mechanical Engineering and his professional degree of Ocean Engineer from the Massachusetts Institute of Technology (MIT) and holds a patent right on an Electronic Control and Response System. His naval assignments include tours in USSRamsey (FFG-2) Aide and Flag Lieutenant to the Commander Naval Electronic Systems Command and Ship Superintendent Surface Type Desk Officer and Assistant Design Superintendent at NA VSHIPYD Pearl Harbor. He was awarded the Meritorious Service Medal for distinguished performance at Pearl Harbor Naval Shipyard. As an author he has contributed articles to the ASNEJournaland given presentations at local sections on ship design the use of innovative technology in ship repair and maintenance and the costs and risks associated with engineering progress. Commander Baskerville is a registered Professional Engineer in the State of Virginia an adjunct professor teaching marine engineering at Virginia Tech. and in addition to ASNE which he joined in 1975 is a member of SNAME Tau Beta Pi Sigma Xi ASME and the American Society of Heating Refrigeration and Air Conditioning Engineers (ASHRAE). Dr. Earl R. Quandt:received his degree of Chemical Engineer from the University of Cincinnati in 1956 and his Ph.D. degree in Chemical Engineering from the University of Pittsburgh in 1961. He worked in the naval reactors program at the Bettis Atomic Power Laboratory from 1956 to 1963. Since that time he has been with David Taylor Naval Ship Research and Development Center Annapolis Maryland where he is Head of the Power Systems Division. He contributed to this paper while on a one year assignment to the U.S. Naval Academy as V

A turning point occurred in naval engineering in 1972 when the U.S. N avy chose to use marine gas turbines for the propulsion of its new SPRUANCE and PERRY Class ships. This paper reviews the more than twenty years of experience with turbine technology and its design integration into combat ships needed to make that decision. It is concluded that the availability of a good second generation aircraft derivative engine with proven reliability and a strong commercial base, i.e., the LM-2500, was as important to the decision as was the predicted improved ship effectiveness and cost benefits. This paper discusses improvements that can be made to the twin engine, single gear, single propeller shaft system. Focusing only on this mechanical transmission concept, it addresses the impact of possible improvements to the engine, gear, and shafting. In particular, the paper discusses current LM-2500 related R&D efforts to: (a) obtain improved part-power fuel rates, (b) integrate with a reversing reduction gear, and (c) add on a waste heat recovery steam cycle. Looking ahead to the year 2000, this paper suggests that a successor to the ubiquitous LM-2500 will appear in the 15 MW power range to provide the next step in the evolution of the twin engine package. This new naval engine will most likely be based on an aircraft core that exists at present, such that it will have demonstrated its reliability and commercial potential through many hours of testing prior to its mid-1990 marine conversion. This new engine is expected to offer improved air flow, an excellent fuel rate (approaching a flat 0.30 LB/HP-HR), and effective maintenance monitoring, all at some expense in size, weight, and cost. The year 2000 engine will burn a liquid hydrocarbon fuel similar to JP-5 because of its aircraft origins. Combined with advances in gear and shafting technology, the full twin engine propulsion system of the year 2000 should be markedly lighter, smaller, and more efficient than today's units.

关键词：

来源：评论

学校读者我要写书评

暂无评论

RETROFITTING OF BULBOUS BOWS ON UNITED-STATES NAVY AUXILIARY AND AMPHIBIOUS WARSHIPS

引用

naval ENGINEERS JOURNAL 1984年第6期96卷 40-51页

作者： CHUN, SK HOUGH, JJ ENGLE, AH FUNG, SC Stephen K. Chunis a graduate of the Maritime College of the State University of New York class of 1981 from which he received a B.E. degree in naval architecture and his license as a Third Assistant Engineer from the U.S. Coast Guard. Since graduation he has worked for the U.S. Navy as a naval architect with the Hull Form and Hydrodynamics Performance Division (SEA 55W3) of the Naval Sea Systems Command. Currently he is the task leader for hydrodynamic design for the DDG-51. He is also responsible for bulbous bow and appendage design for surf ace ships. Mr. Chun is a member of ASNE SNAME and ASE. Jeffrey J. Hough:is currently a naval architect with the Hull Form and Hydrodynamic Performance Division (SEA 55VV3) of the Naval Sea Systems Command (NA VSEA). In his current capacity he is a member of the Surface Ship Hydrodynamics Branch and is the divisional coordinator for computer supported design (CSD) technical director for the hull form design system (HFDS) Hull Engineering Group (SEA 55) assistant coordinator for CSD SEA 55 CSD coordinator for the DDG-51 contract design and SEA 55W3 project engineer for aircraft carrier/aviation support ship hydrodynamics. Mr. Hough received his B.S.E. degree in naval architecture and marine engineering in 1978 and his M.S.E. degree in naval architecture and marine engineering in 1979 from the University of Michigan. He began his career with the U.S. Navy in 1979 as an Engineer-in-Training in the Ship Design and Integration Directorate of NAVSEA. Prior to his current assignment Mr. Hough was the technical director responsible for the hull form and hydrodynamics energy conservation program and technical specialist for design practices for resistance and powering margins and hull form geometry. A member of ASNE since 1979 Mr. Hough is also a member of SNAME ASE and the U.S. Naval Institute. Allen H. Engleis a naval architect with the Hull Form Design and Performance Division of the Naval Sea Systems Command. He received his B.S. degree in engineering science from th

To meet energy conservation goals of the U.S. Navy, its attention has been focused on ways to reduce individual ship total resistance and powering requirements. One possible method of improving ship powering characteristics is by modifying existing individual ship hulls with the addition of bulbous bows. This paper will identify the merits of retrofitting bow bulbs on selected U.S. Navy auxiliary and amphibious warfare ships. A procedure for performing a cost-benefit analysis will be shown for candidate ship classes. An example of this technique for an amphibious warfare ship will also be provided. A brief discussion of future methods to be used for bulbous bow design such as application of systematic model test data and numerical hydrodynamic techniques will be given.

关键词： naval VESSELS

来源：评论

学校读者我要写书评

暂无评论

THE NO FRAME CONCEPT - ITS IMPACT ON SHIPYARD COST

引用

naval ENGINEERS JOURNAL 1984年第3期96卷 218-232页

作者： NAPPI, NS WALZ, RW WIERNICKI, CJ Natale S. Nappi:graduated from City College of New York in 1954 with a B.S. degree in civil engineering and received his M.S. in civil engineering from the Polytechnic Institute of Brooklyn in 1959. He began his professional career in 1954 at the New York Naval Shipyard as a naval architect (structures) performing detail structural design and fabrication studies for CVAs LPDs DDs and CGs and eventually became a supervisory naval architect (structures). From 1965 to 1973 he was a member of the staff of the Computer-Aided Design Division at the David Taylor Naval Ship Research and Development Center (DTNSRDC). As such he was involved in the development of the computer structural design tool the SSDP (in association with Frank M. Lev) and automated detail design programs (CASDOS). His current position is Senior Naval Architect Consultant in the structural integrity group of the Ship Structures Division Structures Department DTNSRDC. Mr. Nappi is the author and co-author of numerous technical papers and reports covering a wide spectrum of topics such as automated structural design process design for producibility and survivability material weight and cost trade-off studies and structural weight determination for high performance ships (i.e. SES SWATH HYSWAS). He has lectured on the subjects of design for survivability and ship structures at the Naval Post Graduate School and MIT. He is a member of ASNE ASCE U.S. Naval Institute Sigma Xi and is a registered Professional Engineer in the State of New York. Mr. Nappi was a member of the NAVSEA working commitee for the computer supported design planning effort and is currently a member of the DTNSRDC ASSET Advisory Committee. Ronald W. Walz:graduated in 1974 from Pennsylvania State University with a B.S. degree in civil engineering. He began his professional career in 1974 at the David Taylor Naval Ship Research and Development Center as a structural engineer in the structural design concepts group of the Ship Structures Division Structures Department.

A proposed cost effective alternative to current U.S. Navy structurally configured hulls is presented in this paper. This proposed design for producibility concept involves the elimination of structural stanchions and transverse web frames. The potential impact of this “no frame” concept on structural design, weight and construction and material costs for naval surface frigates and destroyers is reflected in 1) reduced costs for the installation of distributive systems and 2) a reduced number and complexity of structural details providing a more reliable and less costly structure. This study was performed in three parts: 1) Determine the most feasible length between bulkheads without frames; 2) Using this length perform detail weight studies and construction and material costs analysis comparison on a 72-foot long hull module, with and without frames, for a FFG-7, and 3) Estimate the saving in man hours of labor on the installation of distributive systems and shipfitting for an FFG-7. For the feasible length studies on the “no frame” structural configuration, thirty-seven strength, weight and vertical center of gravity studies were performed on two ship classes; twenty-two on the FFG-7 class and fifteen on the DD-963 class. The detailed weight studies and construction and material cost analyses were conducted for FFG-7 “no frame” and “as built” modules. Results indicating the “no frame” concept module was 6.8% heavier and 14.8% less costly than the “as built” module. For the impact of an FFG-7 “no frame” structurally configured hull on the cost of labor required for the installation of distributive systems and for other functional work such as ship fitting, welding, and electrical, this study indicated a reduction of 169,206 labor hours per ship, representing 7.12% of the total required man hours to fabricate an FFG-7 class ship. With the employment of the “no frame” concept, certain areas of significant concern and potential risk were addressed. These include: 1) t

关键词：

来源：评论

学校读者我要写书评

暂无评论

DESIGN FOR NEW-JERSEY, IOWA, AND DES-MOINES MODERNIZATION

引用

naval ENGINEERS JOURNAL 1984年第3期96卷 25-38页

作者： SIMS, PJ EDWARDS, JR DICKEY, RL SHULL, HS Philip J. Sims:graduated from Webb Institute in 1971 and went to work for the Advance Design Branch of the Naval Ship Engineering Center. He was part of the FFG-7 design team in 1972. The 1973–75 years were spent developing automated early-stage aircraft carrier design procedures and performing carrier design trade-off work in support of the CVV design. He returned to school in 1976 for a masters at M.I. T. The 1977–80 period was spent updating the Navy's destroyer-cruiser early-stage design procedures and performing studies for the CGN-42 reserve FFX and DDX (later DDG 51) projects. Also during this period he was team leader on concept formulation (CONFORM) studies of new ships such as a heavy combatant and a low detectability ship. From 1981 to early 1983 Mr. Sims was Design Integration Manager for the BB-62 and Ship Design Manager for the BB-61 and CA-134. He is presently principal naval architect for the FFX study and also works on the NA TO frigate effort. James F. Edwards Sr:.is the Technical Director Ship Analytics Inc. Washington D.C. Operations and was the Ship Design Manager for the battleship USSNew Jerseyprior to his departure from NAVSEA in August 1983. He joined the U.S. Navy Reserves in 1954 and served on active duty from 1957 to 1960. From 1961 to 1963 he worked for McLaughlin Research Corporation as a section head in the drafting department. From 1963 to 1966 he worked for the Vitro Corporation of America in the Terrier (surface missile systems) Department. In 1966 he participated in the contract design of the first shipboard integrated digital ASW Command and Control system while working for the Stanwick Corporation. In 1967 Mr. Edwards accepted a position at NAVSHIPS in the Combat System Integration Division. In 1974 he transferred to what is currently NAVSEA's Hull Design Division. In 1980 Mr. Edwards was designated as the Battleship and Heavy Cruiser General Arrangements Task Leader and subsequently served as the Hull Task Group Manager the Ship Configuration Control Manager and fina

In reactivating the battleship New Jersey , the Navy faced three major problems. The baseline data on the ship was not readily available or reliable, a new generation cruise missile armament was proposed, and the ship delivery schedule was very tight. After doing a feasibility study, system design engineers were taken onboard the mothballed ship to resolve the design problems. Being on the ship allowed an intensive effort and immediate reference to the actual ship configuration. The tools used to control this effort were a ship check plan, a ship check form and the master arrangement drawing. Simultaneously with the design effort, a repair scoping effort was conducted. The design evolution and solutions to the major problems are described. The results of the New Jersey effort are shown with sample documentation, the ship characteristics and the downstream design effort. The Iowa was the next ship to be modernized. The top level requirements were the same as New Jersey's but new problems were encountered. More options were investigated which diverted attention from the basic effort. A fundamental difference was the Iowa had not had a 1968 reactivation as the New Jersey had, so items that were repair and reactivation on the New Jersey in 1968 had to be part of the Iowa modernization. A major influence on the Iowa design process was that a complete set of specifications for a private yard bid had to be developed. The next effort was to install the same New Jersey modernization payload on a Des Moines class heavy cruiser. Heavy cruisers are large ships but significantly smaller than battleships and much closer to their naval architectural limits of weight and center of gravity. They have much less topside area than the battleships, and the new payload was very topside space consuming. The cruisers are also much more restricted in internal volume. Two feasibility studies were conducted. One resolved volume problems but approached the weight and center of gravity limits.

关键词：

来源：评论

学校读者我要写书评

暂无评论

Theoretical And Experimental Predictions Of The Dynamic Behavior Of Marine Risers

Theoretical And Experimental Predictions Of The Dynamic Beha...

引用

oceanS

作者： C. Chryssostomidis N. Patrikalakis Naval Architecture MIT Sea Grant College Program USA Department of Ocean Engineering Massachusetts Institute of Technology Cambridge MA USA

A comparison of theoretical predictions of the dynamic response of a riser model with experimental measurements is made. The theoretical estimates are obtained from the solution of the linearized structural model of a thin rod under tension. The model of the local hydrodynamic force is based on results from rigid and spring mounted cylinder experiments. The experimental measurements are obtained from a 3m flexible cylindrical model, representative of a shallow water riser. The comparison between theoretical estimates and experimental measurements can be used to evaluate the significance of the assumptions underlying the use of rigid cylinder experimental results for the prediction of the dynamic response of single tube marine risers.

关键词： Strain measurement Prototypes Predictive models Root mean square Estimation theory Testing Frequency measurement Motion measurement Springs Capacitive sensors

来源：评论

学校读者我要写书评

暂无评论

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

请选择保存的检索档案：

请选择收藏分类：

通借通还

建议与咨询 留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

请选择保存的检索档案： 新增检索档案 确定 取消

请选择收藏分类： 新增自定义分类 确定 取消

通借通还

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

请选择保存的检索档案：

请选择收藏分类：