检索结果-内蒙古大学图书馆

Optimization design of flue gas temperature for Low-Low Temperature Electrostatic Precipitator

Journal of Physics: Conference Series 2019年第1期1300卷

作者： Ke Sun Yu Yan Jiahao Jiang Lei Deng State Key Laboratory of Multiphase Flow in Power Engineering School of Energy and Power Engineering Xi'an Jiaotong University Xi'an 710049 China Huadian Electric Power Research Institute Co. LTD. Hangzhou 310030 China

Low temperature corrosion is one of the key issues in application of low-low temperature electrostatic precipitator. The concentration of SO3 affects the acid dew point temperature of flue gas. The exhaust temperature after the air preheater should be higher than the acid dew point temperature. The residual heat of flue gas is fully utilized by the low-temperature economizer. The efficiency of low-low temperature electrostatic precipitator is improved by the comprehensive effect of the condensation of SO3 on the surface of the fine particles, the decrease of the specific resistance of the particles and the agglomeration of the fine particles.

关键词：

来源：评论

学校读者我要写书评

暂无评论

Aeroelastic Analysis of Preset Angle for A Typical Airfoil Section with Cubic Nonlinear Stiffness

引用

Journal of Physics: Conference Series 2019年第1期1300卷

作者： Guofang Nan Di Ding Weitao Wang School of Energy and Power Engineering University of Shanghai for Science and Technology China Shanghai Key Laboratory of Multiphase Flow and Heat Transfer in Power Engineering 516 Jungong Road 200093 Shanghai P.R. China

The influences of the preset angle on the dynamic responses of the typical airfoil section with cubic nonlinear stiffness were investigated under consideration of the aerodynamic flutter onset due to certain angle of attack. The typical airfoil model with cubic nonlinear stiffness is developed to analyze the plunging and the pitching motions for the airfoil section. Based on the Grossman's quasi steady aerodynamic model, the aerodynamic lift and the moment can be obtained and then the equation of motion for the airfoil section is derived by applying the Lagrange theorem. The effects of the preset angle and the oncoming flow speed on the nonlinear dynamics are analyzed by means of the bifurcation diagram, the frequency-amplitude diagram, the time history, etc. Simulation results show that the preset angle influences the intensity of the vibration, moderate or severe, stable or unstable, even under certain circumstance, the jump and chaos phenomenon occur; and the oncoming flow speed affects the distribution of the vibration energy for the plunging and the pitching motions. The unstable stall region for the responding parameters should be avoided to keep the airfoil safe in engineering practice. Some qualitative and quantitative rules are obtained for the airfoil design and the flutter suppression.

关键词：

来源：评论

学校读者我要写书评

暂无评论

Thermodynamic Analysis on of Skid-Mounted Coal-bed Methane Liquefaction Device using Cryogenic Turbo-Expander

引用

IOP Conference Series: Materials Science and engineering 2017年第1期278卷

作者： Shuangtao Chen Lu Niu Qiang Zeng Xiaojiang Li Fang Lou Liang Chen Yu Hou State Key Laboratory of Multiphase Flow in Power Engineering Xi'an Jiaotong University Xi'an 710049 PR China Xinjiang Coal Research Institute Urumqi 830091 PR China

Coal-bed methane (CBM) reserves are rich in Sinkiang of China, and liquefaction is a critical step for the CBM exploration and utilization. Different from other CBM gas fields in China, CBM distribution in Sinkiang is widespread but scattered, and the pressure, flow-rate and nitrogen content of CBM feed vary significantly. The skid-mounted liquefaction device is suggested as an efficient and economical way to recover methane. Turbo-expander is one of the most important parts which generates the cooling capacity for the cryogenic liquefaction system. Using turbo-expander, more cooling capacity and higher liquefied fraction can be achieved. In this study, skid-mounted CBM liquefaction processes based on Claude cycle are established. Cryogenic turbo-expander with high expansion ratio is employed to improve the efficiency of CBM liquefaction process. The unit power consumption per liquefaction mole flow-rate for CBM feed gas is used as the object function for process optimization, compressor discharge pressure, flow ratio of feed gas to turbo-expander and nitrogen friction are analyzed, and optimum operation range of the liquefaction processes are obtained.

关键词：

来源：评论

学校读者我要写书评

暂无评论

Au [email protected] @ZnIn 2 S 4 nanosheets with significantly enhanced visible-light photocatalytic H 2 evolution: The effect of different Au positions on the transfer of electron-hole pairs

引用

Applied Catalysis B: Environmental 2021年 282卷

作者： Siman Mao Jian-Wen Shi Guotai Sun Dandan Ma Chi He Zengxin Pu Kunli Song Yonghong Cheng State Key Laboratory of Electrical Insulation and Power Equipment Center of Nanomaterials for Renewable Energy School of Electrical Engineering Xi'an Jiaotong University Xi'an 710049 China State Key Laboratory of Multiphase Flow in Power Engineering School of Energy and Power Engineering Xi'an Jiaotong University Xi'an 710049 Shaanxi China

Herein, a new type of photocatalysts, Au [email protected] @ZnIn 2 S 4 nanosheets ( [email protected] @ZIS), is elaborately designed for the photocatalytic H 2 evolution from water splitting, where Au nanodots (NDs) are anchored in the pore space of thiol-functionalized UiO66 metal-organic framework (MOF) and ZnIn 2 S 4 nanosheets are wrapped around the UiO66 MOF containing Au NDs. It is found that the different Au positions have a grateful effect on the transfer of photogenerated charge carriers. In [email protected] @ZIS, the photoexcited electrons transfers from ZnIn 2 S 4 to UiOS and then to Au NDs, establishing a smooth transmission channel of electrons. As expected, the optimal sample (Au 4 @ [email protected] 40 ) presents a high photocatalytic H 2 production rate of 391.6 μmol/h (10 mg of catalyst) under visible light irradiation, which is 435.1, 61.2 and 10.2 times higher than that of the pure UiOS, ZnIn 2 S 4 and [email protected] , respectively.

关键词： Photocatalysis Hydrogen evolution Metal-organic framework Thiol- functionalization Au nanodots

来源：评论

学校读者我要写书评

暂无评论

Corrigendum to “Entrainment at T-junction: A review work” [Prog. Nucl. Energy 70 (January 2014) 221–241]

引用

Progress in Nuclear Energy 2014年 71卷 279-279页

作者： Zhaoming Meng Laishun Wang Wenxi Tian Suizheng Qiu Guanghui Su School of Nuclear Science and Technology State Key Laboratory of Multiphase Flow in Power Engineering Xi'an Jiaotong University No. 28 Xianning West Road Xi'an 710049 China

来源：评论

学校读者我要写书评

暂无评论

A new non-destructive method for fault diagnosis of reciprocating compressor by measuring the piston rod strain

引用

IOP Conference Series: Materials Science and engineering 2019年第1期604卷

作者： Xueying Li Xueyuan Peng Xi'an Jiaotong University Xi'an Jiaotong University Xi'an 710049 China State Key Laboratory of Multiphase Flow in Power Engineering Xi'an Jiaotong University Xi'an 710049 China

As an established method to analyse the thermodynamic process inside the cylinder, the p-V diagram can identify typical faults such as leakages through the sealing rings and self-acting valves, loosening and fluttering of the vales, etc. However, the installation of the pressure sensor within the cylinder for recording the p-V diagram may lead to degradation of the cylinder integrity, and hereby potential leakage and lowered strength of the cylinder. This paper presents a new non-destructive method for fault diagnosis of the reciprocating compressor by measuring the piston rod strain, from which the p-V diagram was transformed. An algorithm for reconstruction of the p-V diagram was proposed based on the key feature points on the piston rod load curve that reflect the opening and closing events of the compressor valves. The reconstruction method was validated by comparing the calculated p-V diagrams with the experimental results. The reconstructed p-V diagrams were further used for fault diagnosis of the reciprocating compressors, with which the acoustic emission method was integrated. The results show that this method can easily monitor the working conditions and identify whether and where leakage, fluttering and delayed closing of the valves occur, which indicates that this method can be utilized as a powerful tool of non-destructive condition monitoring and fault diagnosis of the reciprocating compressors.

关键词：

来源：评论

学校读者我要写书评

暂无评论

Development of typical processes and key devices for direct air CO2 capture

引用

Meitan Xuebao/Journal of the China Coal Society 2024年第10期49卷 4203-4221页

作者： Yu, Binpeng Tan, Lei Wang, Ding Wang, Limin Xiang, Xiaofeng Wang, Zhichao Jin, Zhonghua Yang, Bolun Wu, Zhiqiang School of Chemical Engineering and Technology Xi’an Jiaotong University Xi’an710049 China Shaanxi Province Energy and Chemical Process Intensification Key Laboratory Xi’an710049 China School of Engery and Powerl Engineering Xi’an Jiaotong University Xi’an710049 China State Key Laboratory of Multiphase Flow in Power Engineering Xi’an710049 China Shaanxi Engineering Research Center if Coal Fired Boiler Environmental Protection Xi’an710054 China

Conventional carbon capture and storage technologies and carbon capture, utilization and storage technologies mainly target CO2 emissions from fixed sources, while direct air capture CO2 (DAC) technology, as an emerging negative carbon emission technology, can capture CO2 emissions from distributed sources and further reduce the global atmospheric CO2 concentration. In this paper, the development process of DAC's typical liquid absorption process, solid adsorption process and the construction of relevant demonstration projects are introduced, the technical characteristics of emerging DAC processes are analyzed, and the key equipment schemes and future development trends of existing DAC processes are discussed. The DAC liquid absorption process has the characteristics of low cost of absorbent raw materials and high selectivity, which can realize a large-scale continuous capture, but high energy consumption in the regeneration process. The DAC solid adsorption process has the characteristics of modularity, low investment cost, and relatively low energy consumption in the regeneration process, but requires a regular replacement of adsorption materials and maintenance of adsorption equipment, which is suitable for small-scale DAC application scenarios. Two typical DAC process absorption/adsorption materials are reviewed. In the DAC electric oscillation adsorption process, CO2 is chemically captured in the solid electrode, and CO2 desorption is achieved by changing the polarity of the solid electrode with applied electric field. This process has a higher efficiency than that of the heat or pressure-based separation process. The CO2 in the air is selected through the DAC separation membrane to achieve an efficient carbon capture. The DAC process achieves the CO2 absorption and desorption through the change of humidity, which breaks through the high energy consumption limit of conventional variable temperature/pressure swing adsorption. The DAC bio-absorption process absor

关键词： Adsorption

来源：评论

学校读者我要写书评

暂无评论

Corrigendum to “Promoting adiabatic core approximation in a rapid compression machine by an optimized creviced piston design” [Fuel 251 (2019) 328–340]

引用

Fuel 2019年 255卷

作者： Yingtao Wu Meng Yang Chenglong Tang Yang Liu Peng Zhang Zuohua Huang State Key Laboratory of Multiphase Flow in Power Engineering Xi’an Jiaotong University Xi’an 710049 China Department of Mechanical Engineering The Hong Kong Polytechnic University Hung Hom Kowloon Hong Kong

来源：评论

学校读者我要写书评

暂无评论

Non-Hermitian delocalization in a 2D photonic quasicrystal

arXiv

引用

arXiv 2023年

作者： Zhang, Zhaoyang Liang, Shun Septembre, Ismaël Yu, Jiawei Huang, Yongping Liu, Maochang Zhang, Yanpeng Xiao, Min Malpuech, Guillaume Solnyshkov, Dmitry Key Laboratory for Physical Electronics and Devices The Ministry of Education Shaanxi Key Lab of Information Photonic Technique School of Electronic Science and Engineering Faculty of Electronics and Information Xi’an Jiaotong University Xi’an710049 China Institut Pascal PHOTON-N2 Université Clermont Auvergne CNRS Clermont INP Clermont-FerrandF-63000 France International Research Center for Renewable Energy State Key Laboratory of Multiphase Flow in Power Engineering Xi’an Jiaotong University Xi’an710049 China Department of Physics University of Arkansas FayettevilleAR72701 United States National Laboratory of Solid State Microstructures School of Physics Nanjing University Nanjing210093 China Paris75231 France

Quasicrystals show long-range order, but lack translational symmetry. So far, theoretical and experimental studies suggest that both Hermitian and non-Hermitian quasicrystals show localized eigenstates. This localization is due to the fractal structure of the spectrum in the Hermitian case and to the transition to diffusive bands via exceptional points in the non-Hermitian case. Here, we present an experimental study of a dodecagonal (12-fold) photonic quasicrystal based on electromagnetically-induced transparency in a Rb vapor cell. The transition to a quasicrystal is obtained by superposing two honeycomb lattices at 30◦ with a continuous tuning of their amplitudes. Non-Hermiticity is controlled independently. We study the spatial expansion of a probe wavepacket. In the Hermitian case, the wavepacket expansion is suppressed when the amplitude of the second lattice is increased (quasicrystal localization). We find a new regime, where increasing the non-Hermitian potential in the quasicrystal enhances spatial expansion, with the C12 symmetry becoming visible in the wavepacket structure. This real-space expansion is due to a k-space localization on specific quasicrystal modes. Our results show that the non-Hermitian quasicrystal behavior is richer than previously thought. The localization properties of the quasicrystals can be used for beam tailoring in photonics, but are also important in other fields. Copyright © 2023, The Authors. All rights reserved.

关键词： Quasicrystals

来源：评论

学校读者我要写书评

暂无评论

Numerical Study of Evaporation and Motion Characteristics of Liquid Nitrogen Droplet in High-Speed Gas flow

引用

IOP Conference Series: Materials Science and engineering 2017年第1期278卷

作者： Y. Ruan L. Chen X. Liu S. Chen Y. Hou State Key Laboratory of Multiphase Flow in Power Engineering Xi'an Jiaotong University Xi'an 710049 PR China Xi'an Jiaotong University Suzhou Academy Suzhou 215123 PR China

In the cryogenic wind tunnel, cooling the circulating gas to cryogenic temperature by spraying liquid nitrogen (LN2) is an efficient way to increase the Reynolds number. The evaporation and motion of LN2 droplets in the high-speed gas flow is the critical process that determines the cooling rate, cooling capacity and the safe operation of the down-stream compressor. In this study, a numerical model of droplet motion and evaporation in high-speed gas flow is developed and verified against experimental data. The droplet evaporation rate, diameter and velocity are obtained during the evaporation process under different gas temperatures and flow velocities. The results show that the gas temperature has dominant influence on the droplet evaporation rate. High flow speed can increase droplet evaporation effectively at the beginning process. Evaporation of droplets with different diameters follows a similar trend. The absolute evaporation rate increases with the increase of droplet diameter while the relative evaporation amount is highest for the smallest droplet due to its high area-volume ratio. This numerical study provides insight for understanding the evaporation of LN2 droplets in high-speed gas flow and useful guidelines for the design of LN2 spray cooling.

关键词：

来源：评论

学校读者我要写书评

暂无评论

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

请选择保存的检索档案：

请选择收藏分类：

通借通还

建议与咨询 留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

请选择保存的检索档案： 新增检索档案 确定 取消

请选择收藏分类： 新增自定义分类 确定 取消

通借通还

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

请选择保存的检索档案：

请选择收藏分类：