检索结果-内蒙古大学图书馆

Preparation, improvement, and application of metal–organic framework-based sensing materials for gas leakage and emission: A review

引用

Nano Materials Science 2025年

作者： Liu, Manyi Wang, Liang Ren, Shan Bai, Bofeng Chai, Shouning He, Chi Zheng, Chunli Yin, Xitao Li, Fengguang College of Materials Science and Engineering Chongqing University Chongqing400044 China State Key Laboratory of Multiphase Flow in Power Engineering School of Energy and Power Engineering Xi'an Jiaotong University Xi'an710049 China School of Physics and Optoelectronic Engineering Ludong University Yantai264000 China School of Materials Science and Engineering Hubei University of Automotive Technology Shiyan442002 China

Industrial gas leaks and flue gas emissions pose significant threats to the safety of industrial operations and the atmospheric ecological environment. Traditional gas sensing materials often struggle to meet the challenges posed by complex industrial environments. Recently, metal-organic framework (MOF)-based gas sensing materials have garnered significant attention in industrial gas detection due to their high sensitivity, selectivity, and tunable properties. The exponential increase in related publications highlights the growing research interest in this field. This paper presents a comprehensive review of the advantages of various types of metal-organic frameworks and their derivatives for detecting industrial gas leaks and flue gas emissions, alongside an introduction of representative MOF synthesis methods. Furthermore, the primary sensing mechanisms of MOF-based gas sensing materials and strategies for enhancing the sensing performance are summarized. The current state of MOF-based gas sensing materials in industrial gas detection is also discussed. Finally, the potential limitations, existing challenges, and future directions of MOF-based industrial gas sensing materials are systematically analyzed, with suggestions for addressing these challenges to advance industrial gas detection technologies. © 2025 Chongqing University

关键词： Application Improvement Industrial gas detection MOF-Based sensing materials Preparation

来源：评论

学校读者我要写书评

暂无评论

A 3D-dimensional interconnected structured poly (m-phenylene isophthalamide) nanofiber separator with Li1.5Al0.5Ge1.5(PO4)3 for high-safety lithium-sulfur batteries

引用

Journal of power Sources 2025年 645卷

作者： Liu, Jianwei Zhu, Lei Chai, Qinqin Sun, Shiyi Yang, Xiaomeng Sun, Jingyun Zhang, Yating Zhu, Youyu Yan, Wei College of Chemistry and Chemical Engineering Xi'an University of Science and Technology Shaanxi Xi'an710054 China Key Laboratory of Multiphase Flow in Power Engineering Xi'an Jiao tong University Shaanxi Xi'an710049 China Xi'an Hantang Analysis & Test Co. Ltd Shaanxi Xi'an710201 China

Safety concerns have consistently presented substantial obstacles to the widespread adoption of lithium-sulfur (Li-S) batteries. Conventional polyolefin separators, which are characterized by low flash points and insufficient mechanical strength, pose potential safety hazards, including risks of fire and explosion under extreme operating conditions. In this study, we introduce a thermally stable and non-flammable poly-m-phenyleneisophthalamide (PMIA)-based multifunctional separator (L-PMIA separator), which is enhanced with lithium aluminum germanium phosphate (Li1.5Al0.5Ge1.5(PO4)3 or LAGP) fillers. By incorporating g high-ionic-conductivity LAGP and establishing an interconnected framework, this design effectively mitigates the issues of particle agglomeration and uneven commonly ion transport associated with traditional separators. The L-PMIA separator demonstrates remarkable mechanical strength (with a tensile strength of 8.5 MPa and a puncture force of 0.72 N) and thermal stability (showing no dimensional shrinkage even at 200 °C), while also facilitating the formation of continuous ion channels that inhibit lithium dendrite growth. Consequently, Li-S batteries utilizing the 4L-PMIA separator demonstrated a reversible capacity of 4.97 mAh cm−2 after 150 cycles, even under conditions of high sulfur loading (6.75 mg cm−2), limited electrolyte availability (E/S = 7), and elevated temperatures. This approach offers novel insights for the development of future energy storage systems characterized by enhanced safety and performance. © 2025 Elsevier B.V.

关键词： Lithium sulfur batteries

来源：评论

学校读者我要写书评

暂无评论

Effect of surface roughness on corrosion behaviour of stainless steel in supercritical CO 2

引用

Journal of Materials Research and Technology 2025年 36卷 4946-4954页

作者： Liyong Cao Wenyan Zhang Chongjun Jiang Hui Wang Hong An Chao Ye Jiyun Ren Xiaole Huang Lei Deng China University of Xihua Chengdu 610039 China State Key Laboratory of Multiphase Flow in Power Engineering School of Energy and Power Engineering Xi'an Jiaotong University Xi'an 710049 China China University of Petroleum-Beijing Beijing 102249 China PipeChina Gansu Branch Lanzhou 730070 China Zhengzhou Yutong Group Co. Ltd. Zhengzhou 450000 China

To study the effect of surface roughness on the corrosion behavior of austenitic steels in supercritical CO 2 , the corrosion experiments were conducted on 304 and 310S stainless steels at 550 °C and 15 MPa. The corroded samples were characterized using XRD and SEM-EDS. The results demonstrate that surface roughness significantly affects the morphology and structure of the oxide films formed on 310S stainless steel. Samples prepared with varying surface roughness (grounded using from 200# to 1000# metallographic abrasive papers) showed that rougher surfaces tend to develop denser oxide layers, whereas smoother surfaces exhibit relatively loose and porous oxide films. Despite these differences in oxide structure, the overall corrosion weight gain remained largely unaffected, indicating minimal oxide shedding from 310S steel. The oxidation product is mainly Cr 2 O 3 . For 304 stainless steel, surface roughness was found to influence the composition of surface oxides. Both 200# and 1000# samples formed loose, porous oxide films prone to spallation, with the primary constituents being Fe 3 O 4 , (Fe, Cr) 3 O 4 and Fe 2 O 3 . Because the content of (Fe, Cr) 3 O 4 and Fe 3 O 4 of the former is higher, more voids appear in the oxide film, leading to spallation within the first 100 h of exposure. The rougher surface showed a more pronounced loss of oxide. But for the 600# sample, the main component is Fe 2 O 3 . Carburization was observed to intensify with increasing surface roughness in both materials. Notably, the 200# sample of 310S stainless steel exhibited more severe carburization compared to the 1000# sample of 304 stainless steel.

关键词： Supercritical CO 2 Corrosion Austenitic stainless steels Surface roughness Oxidation

来源：评论

学校读者我要写书评

暂无评论

Uncertainty and Sensitivity Analysis of Containment Aerosol Removal Under Severe Accident

SSRN

引用

SSRN 2025年

作者： Ou, Pingwen Chen, Yongzheng Chen, Peng Ouyang, Yong Guo, Chao Su, Guanghui China Nuclear Power Technology Research Institute Co. Ltd. Shenzhen518000 China State Key Laboratory of Nuclear Power Safety Technology and Equipment China Nuclear Power Technology Research Institute Co. Ltd. Shenzhen518000 China School of Nuclear Science and Technology Xi'an Jiaotong University Shaanxi Xi’an710049 China State Key Laboratory of Multiphase Flow in Power Engineering China

This study focuses on the uncertainty and sensitivity analysis of containment aerosol removal under severe accident conditions using the severe accident integral code ASTEC, validated by experiments carried by CNPRI, and the coupled uncertainty and sensitivity tool SUNSET. A "separated" methodology is introduced, which distinguishes between thermal-hydraulic and aerosol boundary conditions to highlight the impact of containment aerosol mechanisms. Eleven uncertainty input parameters related are selected for uncertainty propagation and the Spearman correlation coefficient is utilized to describe sensitivity. The removal factor exhibits significant variation, with peaks due to temporary enhancement of diffusiophoresis deposition caused by corium relocation and subsequent steam generation. Uncertainty in the removal factor is substantial before aerosol release termination and narrows afterward. The gravitational settling and the diffusiophoresis deposition are the most important contributors with approximately 70% and 20% deposited aerosol mass, respectively. The initial mass medium diameter, the gravitational shape factor and the agglomeration shape factor are the most influential input parameters in aerosol removal, including in-containment deposition and environmental release, and they should be considered discreetly with conservatism in source term estimation and radioactive consequence evaluation in nuclear engineering. © 2025, The Authors. All rights reserved.

关键词： Sensitivity analysis

来源：评论

学校读者我要写书评

暂无评论

Simulation study of channel structural design for direct internal reforming methane solid oxide fuel cell

引用

Applied Thermal engineering 2025年 274卷

作者： Wu, Wenzhao Bi, Xiaobing Lv, Xuecheng Li, Yang Zhou, Zhifu Wu, Wei-Tao Wei, Lei Lyu, Jizu Li, Yubai Song, Yongchen Key Laboratory of Ocean Energy Utilization and Energy Conservation of Ministry of Education Dalian University of Technology Dalian116024 China State Key Laboratory of Multiphase Flow in Power Engineering Xi'an Jiaotong University Xi'an710049 China School of Mechanical Engineering Nanjing University of Science and Technology Nanjing210094 China Department of Mechanical and Energy Engineering Southern University of Science and Technology Shenzhen518055 China School of Mechanical Engineering Guangdong Ocean University Zhanjiang524088 China

Reasonable designs on channels could effectively improve cell performance. This study established a 3D model of planar solid oxide fuel cell directly fueled by methane to investigate the impacts of three independently designed channel structures. This includes modifications to the channel cross-sectional shape (trapezoid and bow), inserting petal-shaped obstacles (single-layer and double-layer), and the study of deflector sheets embedded into the anode channel to address the highly endothermic nature of the methane steam reforming reaction. The research results indicated that, whether trapezoidal or bowed cross-sections are used, the current density achieves the largest growth rate at L_a = 1.5W_CH (16.06 % for bow and 15.53 % for trapezoid). Additionally, double-layer obstacles provide a greater enhancement of current density than single-layer obstacles (11 % for single-layer, 18 % for double-layer) and result in smaller and more uniform fuel flow velocity distribution in the channel. Embedding two or three deflector sheets into the anode channel significantly reduces the maximum temperature difference (by 7 K for two sheets;by 10 K for three sheets, representing a nearly 48 % reduction) and notably improves the temperature distribution uniformity. The study provides a novel perspective on channels alteration which could contribute to the advancement of researches on high-efficiency SOFCs. © 2025 Elsevier Ltd

关键词： Deflection (structures)

来源：评论

学校读者我要写书评

暂无评论

Teardrop-like micro pin fin coated nanotube arrays chip for enhancement of flow boiling electronics cooling

引用

International Journal of Thermal Sciences 2025年 214卷

作者： Chen, Hongqiang Gao, Quan Ma, Xiang Li, Kai Du, Wangfang Li, Caifeng Zhang, Yonghai Wei, Jinjia School of Chemical Engineering and Technology Xi'an Jiaotong University 28 Xianning West Road Shaanxi Xi'an710049 China Key Laboratory of Multiphase Flow in Power Engineering Xi'an Jiaotong University Xi'an710049 China National Microgravity Laboratory Institute of Mechanics Chinese Academy of Sciences Beijing100190 China School of Engineering Science University of Chinese Academy of Sciences Beijing100149 China Xi'an Shaangu Power Co. Ltd. Xi'an710075 China

Phase change flow boiling heat transfer in microchannel is a very efficient thermal management mode for high-power electronics/devices cooling. However, achieving comprehensive enhancement of flow boiling heat transfer performance at low power consumption is still challenging. Herein, we devised and manufactured a teardrop-like micro-pin-fin coated stable copper hydroxide nanotubes array chip surfaces (S-Nanotube), demonstrating their exceptional enhancement in flow boiling heat transfer efficiency. A series of experiments were conducted using HFE-7100 as a working fluid within a semi-open microchannel. Compared to the smooth surface, the critical heat flux (CHF) and the maximum boiling heat transfer coefficient (HTC) of the S-Nanotube is increased by 82.1 % (from 45.1 to 72.9 and then to 82.1 W/cm2) and 140.5 % (from 5955 to 11,325 and then to 14,316 W/m2·K) at extremely low-pressure drop (≤4 kPa), showing a high coefficient of performance (COP). The temperature of the onset of nucleate boiling on the S-Nanotube surface is reduced by 26.4 %, and the heat flux is greatly increased in a small wall temperature variations (ΔT ≤ 10 °C). In situ observation and analysis of the surface properties and the bubble dynamics, the S-Nanotube chip promotes the phase change heat transfer process by providing massive nucleation sites, reducing bubbles size and residence time, and enhancing the wicking wetting capacity. These findings provide guidance for the rational design of boiling heat transfer-enhanced surfaces and heat sinks and point the way to achieving efficient thermal management of power devices. © 2025 Elsevier Masson SAS

关键词： Electronic cooling

来源：评论

学校读者我要写书评

暂无评论

Research on flow characteristics of dual-outlet centrifugal disk blood pumps

引用

Shengwu Yixue Gongchengxue Zazhi/Journal of Biomedical engineering 2025年第2期42卷 374-381页

作者： Lian, Qilong Xiao, Yuan Xiao, Yiping Cao, Zhanshuo Cui, Guomin Shanghai Key Laboratory of Multiphase Flow and Heat Transfer in Power Engineering School of Energy and Power Engineering University of Shanghai for Science and Technology Shanghai200093 China

Tesla blood pumps demonstrate a reduced propensity for hemolysis and thrombosis compared with vane blood pumps. Considering the restricted driving force within the secondary flow channel of vane blood pumps, along with the low hydraulic efficiency of conventional Tesla blood pumps and their internal flow characteristics that significantly contribute to hemolysis and thrombosis, this study introduces a set of vanes atop the rotor of the Tesla blood pump. This forms a dual-fluid domain rotor, and an axial dual-outlet volute shell structure is adopted to realize the separation of the fluid domains. Through numerical simulations of the new structure, a comparative analysis was conducted in this study on the internal flow characteristics of double-outlet and single-outlet volute shells, and symmetric and asymmetric cross-sections of the same rotor. The results indicate that the flow field distribution is more uniform under the double-outlet volute shell structure, and overall energy dissipation is decreased. After implementing the double-outlet design, in the asymmetric cross-section, compared with the symmetric cross-section, the fluid velocity gradient and turbulent kinetic energy at the tongue of the septum are reduced, and the fluid velocity gradient at the convergence of the diffuser tube outlets are also decreased. The maximum scalar stress is lower, and the decline in head and efficiency is mitigated. Moreover, compared with the single-outlet volute shell, the hemolysis index in the asymmetric cross-section is reduced. In summary, this paper proposes a novel dual-outlet centrifugal disk blood pumps, which can provide a reference for the structural design and performance optimization of magnetically levitated centrifugal blood pumps. © 2025 West China Hospital, Sichuan Institute of Biomedical engineering. All rights reserved.

关键词： Shells (structures)

来源：评论

学校读者我要写书评

暂无评论

Thermodynamics analyses on a novel CHP system integrated with multi-grade thermal energy storage

引用

Journal of Energy Storage 2025年 106卷

作者： Liu, Rongtang Zhang, Kezhen Qin, Yuanzhi Wan, Kaidi Xu, Can Liu, Ming Ningbo Institute of Technology Beihang University Ningbo315800 China Xi'an Thermal Power Research Institute Co. Ltd. Xi'an710054 China State Key Laboratory of Multiphase Flow in Power Engineering Xi'an Jiaotong University Xi'an710049 China Dongfang Boiler Co. Ltd. of Dongfang Electric Group Chengdu611731 China

The high penetration level of intermittent renewable power necessitates the crucial requirement for combined heat and power systems to possess both high efficiency and flexibility. However, the heat-controlled operation modes of traditional combined heat and power systems impose limitations on their efficiency and flexibility. Therefore, it is of great significance to develop a heat-power decoupling technology that exhibits exceptional efficiency and flexibility. A novel combined heat and power system integrated with multi-grade thermal energy storage is proposed in this study. Thermodynamic analysis models of all operational conditions are developed, and the comprehensive characteristics of efficiency and operational flexibility for the proposed system are assessed by taking a 330 MW system as an example. Results show that the proposed system can decrease/increase 16.05 MW/30.96 MW power loads comparing with the reference system during the charging/discharging periods under the design condition. Energy efficiency of the proposed system can reach 49.40 %, which is improved by 1.66 percentage points. Exergy analysis reveals the exergy destruction order for the proposed system, and shows that the combustion and heat transfer in the boiler are the major process of exergy dissipation. Moreover, operation strategies of the proposed system during charging-discharging cycle are explored and formulated under off-design condition, suggesting that thermodynamic performances of the novel system under various conditions even extreme conditions exhibits exceptional properties. The maximum heat load of the proposed system can be improved by 46.78 % comparing with the reference system, and the maximum improvement of power load capacity during charging-discharging cycle is 14.58 percentage points. This study provides a promising approach for multi-grade thermal energy storage to improve the comprehensive characteristics of combined heat and power systems. © 2024

关键词： Charge storage

来源：评论

学校读者我要写书评

暂无评论

Numerical Investigation of the Thermal Response to Skin Tissue during Laser Lipolysis

引用

Journal of Thermal Science 2018年第5期27卷 470-478页

作者： CHEN Bin ZHANG Yue LI Dong State Key Laboratory of Multiphase Flow in Power Engineering Xi'an Jiaotong University

Laser lipolysis can effectively treat obesity and its associated diseases, such as hypertension, fatty liver, and hyperlipidemia. However, currently available invasive laser lipolysis, which transmits laser to a fiber-optic catheter inserted into the subcutaneous tissue for irradiation through an incision, may cause hematomas, infections, and empyrosis. The current study presents a novel, noninvasive approach for laser lipolysis, which directly irradiates the intact skin surface without an incision and preferentially targets adipose tissue at the near-infrared band. High laser energy is necessary to damage adipocytes; however, this may carbonate and burn the dermis. Therefore, the introduction of skin cooling is essential to avoid unwanted hyperthermal injury and improve the threshold of radiant exposure. In the current study, we investigated a novel noninvasive approach assisted with skin cooling by establishing a homogeneous multi-layer skin model. In this method, light propagation in the skin was simulated by using the Monte Carlo method. Skin cooling was employed before laser irradiation to protect the epidermis from thermal damage, which was treated as a boundary condition based on Newton's law. The numerical results showed that the photons were deposited in the adipose layer more than in the other layers. Laser can effectively destroy adipose tissue at an energy density of >200 J/cm^2 at 1210 nm wavelength, whereas at least 300 J/cm^2 is required at 1064 nm to achieve the same effect. In this experiment, at >5 s pulse width, the selectivity of adipose was not obvious. Moreover, the results indicated that 60 ms R134a or R404a spray can effectively reduce the temperature of the epidermis. R404a exhibited a stronger cooling effect than R134a. Cold air cooling at -10 °C for 10 s could effectively decrease the skin temperature, and deeper cooling could be achieved by cold air cooling compared with cryogen spray cooling.

关键词： laser lipolysis Nd:YAG laser multi-layer skin model skin cooling

来源：评论

学校读者我要写书评

暂无评论

Experimental Investigation on Heat Transfer Characteristics of Water in Inclined Downward Tube of a Supercritical Pressure CFB Boiler

引用

Journal of Thermal Science 2015年第5期24卷 478-487页

作者： WANG Siyang YANG Dong XIE Beibei WANG Long WANG Yongjie State Key Laboratory of Multiphase Flow in Power Engineering Xi’an Jiaotong University

In this study, experiments have been performed for an investigation on heat transfer of water in an inclined downward tube with an inner diameter of 20 mm and an inclined angle of 45° from the horizon, with the range of pressure from 11.5 to 28 MPa, mass flux from 450 to 1550 kg/(m2 s), and heat flux from 50 to 585 k W/m2. Based on the experimental data, the temperature distribution in the tube wall was derived. The heat transfer characteristics of inclined downward flow were compared with that of vertical downward flow. The effects of heat flux on wall temperature were analyzed and the corresponding empirical correlations were presented. The results show that heat transfer characteristics of water in the inclined downward tube are not uniform along the circumference from the top surface to the bottom surface. An increase in heat flux exacerbates the non-uniformity. At subcritical pressures, both dry-out and departure from nucleate boiling(DNB) occur at the top surface of the inclined downward tube; inversely, only dry-out takes place on the bottom surface of the inclined downward tube and in the vertical downward tube. At near-critical pressures, DNB and dry-out occur in the comparing tubes with greater possibility. At supercritical pressures, heat transfer gets enhanced in the pseudo-critical enthalpy region; in the high enthalpy region, the top surface temperature of the inclined downward tube decreases obviously.

关键词： inclined downward tube wall temperature circumferential non-uniformity heat transfer deterioration

来源：评论

学校读者我要写书评

暂无评论

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

请选择保存的检索档案：

请选择收藏分类：

通借通还

建议与咨询 留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

请选择保存的检索档案： 新增检索档案 确定 取消

请选择收藏分类： 新增自定义分类 确定 取消

通借通还

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

请选择保存的检索档案：

请选择收藏分类：