检索结果-内蒙古大学图书馆

IEEE General Meeting power& Energy Society

作者： Yisha Lin Ying Qiao Zongxiang Lu Jin Li State Key Lab of Control and Simulation of Power Systems and Generation Equipment Tsinghua University Beijing China Wind Power Technology Center State Grid Gansu Electric Power Company Lanzhou China

ISBN: (数字)9781728155081

ISBN: (纸本)9781728155098

Cleanliness of energy system requires both NO x reduction due to urgent air pollution control and CO 2 cutting due to long-term climate change pressure. In the urban heating sector, quick-win plans use to be popular that focus on the NO x reduction by replacing untreated scattered coal fired boilers to natural gas or combined heat and power generators (CHPs). Meanwhile, in the electrical sector, all these fossil fuel generators should be cut down in the long-term decarbonization process. There should be a need for coordination of short- and long-term targets, because two energy supply sectors are believed to work in a coupled way in the future. A three-layered collaborative planning model is proposed in this paper: the top layer focuses roadmap economic evaluation; the middle layer applies coupled production simulation aiming at verifying energy balance; and the bottom one checks real-time operational feasibility. Pathways are made from 2020 to 2040 based on Hebei, China. Results indicate that the pathway with quick win will have delayed construction of renewable power, resulting the slow process in emission control. The long-term strategy scheme greatly promotes the renewables for supply in both sectors, but the close operational link forces the decoupling, leading to rebound on emission and operation cost on decentralized heating for the long-term future. In conclusion, the tradeoff pathway, reducing CO 2 emission as much as possible with NO x emission controlled to acceptable level, is recommended with good performance on emission control and economy.

关键词： Cogeneration Process control Production Air pollution Generators Real-time systems Planning

来源：评论

学校读者我要写书评

暂无评论

The Actual Operation of Transmission Line and Evaluation of the Reclosing Time of Reclosure

The Actual Operation of Transmission Line and Evaluation of ...

引用

2017 International Conference on Mechanical and Mechatronics Engineering(ICMME2017)

作者： Rui-ming OU Gun YANG Zhan-qing YU Jin-bo WU Shui-ming CHEN Hong-jun ZHEN Qingyuan Power Supply Bureau of Guangdong Grid Company State Key Lab.of Control and Simulation of Power Systems and Generation Equipment Department of Electrical EngineeringTsinghua University

In this paper,the actual trip of typical transmission line is *** includes the trip frequency of transmission lines and the tripping frequency caused by lightning,seasonal distribution characteristics of transmission line trip,and the success rate of reclosing on the transmission *** this paper,the probability of the occurrence of the trip again is evaluated based on the duration of ground lightning *** the increase of the time of reclosure,the probability of the occurrence of the trip will *** this calculating method,the average probability of tripping of reclosure decreased significantly during a ground lightning stroke process,when the reclosing time t0 is 1 s.

关键词： Trip of transmission line Trip caused by lightning Reclosing time of reclosure Probability of tripping of reclosure

来源：评论

学校读者我要写书评

暂无评论

The Method for Evaluating the Reclosing Time of Reclosure Based on Lightning Parameters

The Method for Evaluating the Reclosing Time of Reclosure Ba...

引用

2017 International Conference on Mechanical and Mechatronics Engineering(ICMME2017)

作者： Gun YANG Zhan-qing YU Hong-jun ZHEN Chao SU Shui-ming CHEN Rong ZENG Jin-liang HE State Key Lab.of Control and Simulation of Power Systems and Generation Equipment Department of Electrical EngineeringTsinghua University Qingyuan Power Supply Bureau of Guangdong Grid Company

The fault of transmission line is mostly caused by lightning,and a ground lightning stroke process is often accompanied by multiple *** duration of ground lightning stroke are also *** this paper,a method for evaluating the reclosing time of reclosure based on lightning parameters is *** addition,this paper also gives an expression for the cumulative rate of the duration of ground lightning stroke,and an expression for probability distribution of the amplitude of lightning current in Guangdong *** also proposed a method for calculating the probability of tripping of *** this calculating method,the average probability of tripping of reclosure is less than 1/10000 during a ground lightning stroke process,when the reclosing time t0 is greater than 1.012 s.

关键词： Ground lightning stroke Lightning parameters Reclosing time of reclosure Probability of tripping of reclosure

来源：评论

学校读者我要写书评

暂无评论

Analysis of Adaptive Re-closure in AC-DC Hybrid power System

Analysis of Adaptive Re-closure in AC-DC Hybrid Power System

引用

International Conference on Advanced power System Automation and Protection (APAP)

作者： Min Xie Wei Zhang Ludeng Liu Xin Jia Bin Wang Xinzhou Dong Dispatching and Controlling Center of Anhui Electric Power Company State Grid Hefei China Key Lab of Control and Simulation of Power Systems and Generation Equipment Tsinghua University China

ISBN: (数字)9781728117225

ISBN: (纸本)9781728117232

The beat frequency characteristic of the recovery voltage of fault phase in the case of single-phase grounding transient fault happening to line with the shunt reactors is analyzed. Besides, the paper analyzes the reason of no beat frequency phenomenon of transient fault happening to line without shunt reactor. The AC power networks with metallic grounding fault and arc grounding fault are analyzed by simulation. The recovery voltage of single-phase grounding fault in AC/DC hybrid power grid is studied by PSCAD. The new problems of the adaptive re-closure in AC-DC hybrid power system are discussed. Then the follow-up ideas to solve several existing problems are also presented.

关键词： Circuit faults Inductors Shunts (electrical) Transient analysis Integrated circuit modeling Grounding Capacitance

来源：评论

学校读者我要写书评

暂无评论

Current differential protection based on Non-Conventional Instrument Transformer and IEC61850

Current differential protection based on Non-Conventional In...

引用

International Universities power Engineering Conference (UPEC)

作者： Kun Liu Xinzhou Dong Zhiqian Bo State Key Laboratory of Control and Simulation of Power System and Generation Equipments Department of Electrical Engineering Tsinghua University Beijing China AREVA T&D Automation슠and Information Systems Staffordshire UK

Non Conventional Instrument Transformer (NCIT) and IEC 61850 are crucial technologies in digital substations. But they bring some new uncertainties to protection IEDs, especially the time synchronization issue in current differential protection. The paper analyzes the time delay of transferring sampled values from NCIT to current differential relay in NCIT and IEC61850 based digital substation, then finds out the delay-non-deterministic problem, at last presents a novel current differential protection scheme by using Phase-Locked Loops (PLL ) technology.

关键词： Substations Delay effects Synchronization IEC Phase locked loops Data communication Ethernet networks

来源：评论

学校读者我要写书评

暂无评论

A Novel Structure Design of Iron Core for power Transformers Considering Joints Forms and Magnetostriction.

A Novel Structure Design of Iron Core for Power Transformers...

引用

International Conference on Magnetics (INTERMAG)

作者： J. Li S. Wang H. Gao M. Liu J. Hong State Key Laboratory of Control and Simulation of Power System and Generation Equipments Tsinghua University Beijing China State Key Laboratory of Reliability and Intelligence of Electrical Equipment Hebei University of Technology Tianjin China

Body: power transformers and reactors are important devices in power transmission systems. But their cores and windings could produce vibration and acoustic noise by magnetostrictive effect, Maxwell electromagnetic stress and Lorentz force. Noise has become a bad environmental pollution source in some situations, and its vibration and noise reduction has become an urgent problem need to be solved. The shapes, materials, magnetostriction and joints forms of iron cores, the limitations of test, modeling, and experimental measurement of vibration and noise characteristic, are all the difficult reasons to analyze the vibration and acoustic noise of transformers and reactors. 1. The magnetostrictive modeling can be divided into two steps based on the magnetic field force and materials deformation, so the magnetic field force will be fed into the structural finite element with Maxwell electromagnetic force produced on the interface between the iron core and the air to calculate the deformation of the magnetic materials and to make the model more general and consistent. In order to fully verify the correctness of the model in the magnetostrictive analysis, and to ensure the simplicity of test and avoid unnecessary interference factors, the most simple magnetostriction tests will be carried out by using a single closed circle or rectangular electrical steel sheet, as shown in Fig. 1(a). The tests will measure the relationship between magnetostriction and magnetic field of different magnetic materials, different saturations, different sizes and different shapes. 2. The joint is a necessary form for the stacking of large transformer iron cores, and the main joint form is the step jiont at present. The introduction of the joints causes the magnetic force lines to flow through the different laminations and to make the local magnetic field complicated. From simple to complex process is adopted in this paper, and the verification is gradually complicated. Based on the study of a

关键词： Magnetics Conferences

来源：评论

学校读者我要写书评

暂无评论

Reliability Assessment of generation and Transmission systems Considering Multi-Form Access of "Source-Network-Load-Storage"

Reliability Assessment of Generation and Transmission System...

引用

2019 IEEE Sustainable power and Energy Conference, iSPEC 2019

作者： Qi, Ning Cheng, Lin Jiang, Yi Luo, Jinshan Sun, Ke Wang, Dan Cheng, Liang Wang, Quanquan Tsinghua University State Key Lab. of Control and Simulation of Power System and Generation Equipment Beijing China State Grid Economic and Technological Research Institute Co. Ltd. Beijing China State Grid Jiangsu Electric Power Co. LTD. China State Grid Jiangsu Economic Research Institute Jiangsu China

ISBN: (纸本)9781728149301

Reliability assessment is the key to ensure the security of power system, however, the rapid development of "source-network-load-storage" cause enormous obstacle to the traditional reliability method. A improved method for reliability assessment of generation and transmission systems is proposed in this paper which lays importance on the coordinate operation and uncertainty of "source-network-load-storage". Firstly, the reliability and operation model of "source-network-load- storage" is proposed to handle certain novel elements. Then the reliability assessment with operation simulation is proposed to make balance between generation and load under uncertainty. Finally, numerical analysis focusing on the different form and proportion of "source-network-load-storage" is tested in IEEE RTS-79 system so as to demonstrate the practicality and effectiveness of the improved method. © 2019 IEEE.

关键词： Renewable energy resources

来源：评论

学校读者我要写书评

暂无评论

Substation switching electromagnetic transient analysis using the time domain integral equation with a high order implicit scheme

Substation switching electromagnetic transient analysis usin...

引用

IEEE International Symposium on Electromagnetic Compatibility (EMC)

作者： Hongjun Xiang Sughun Chang Jun Zou Jians heng Yuan Sergey V. Shenderey State Key Laboratory of Control and Simulation of Power Systems and Generation Equipments Department of Electrical Engineering Tsinghua University Beijing China Electrical Environment Group Korea Electrotechnology Research Institute Changwon South Korea

A fast electric field integral in time domain using the uneven discretization and the implicit scheme is proposed to calculate the switching electromagnetic transient at a substation. The switching transient currents and the resultant radiated electromagnetic field are calculated. The propose d approach has the strength to model the bus system at a substation with a more complicated and realistic configuration that is difficult to simulate using the circuit-based method, because all the electromagnetic couplings within the bus system are included globally. The proposed method might be one of good candidates to predicate the EMI level at a substation.

关键词： Transient analysis Switches Time domain analysis Wires Integrated circuit modeling Conductors

来源：评论

学校读者我要写书评

暂无评论

Design of an additive manufactured XY compliant manipulator with spatial redundant constraints 35

Design of an additive manufactured XY compliant manipulator ...

引用

第35届中国控制会议

作者： ZHANG Zhen LIU Binbin WANG Peng YAN Peng State Key Laboratory of Tribology & Institute of Manufacturing Engineering Department of Mechanical EngineeringTsinghua University Beijing Key Lab of Precision/Ultra-precision Manufacturing Equipments and Control Tsinghua University State Key Laboratory of Fluid Power and Mechatronic Systems Zhejiang University School of Automation Science and Electrical Engineering Beihang University School of Mechanical Engineering Shandong University

ISBN: (纸本)9781509009107

This paper presents an additive manufactured beam flexure-based XY positioning stage with spatial redundant *** order to restrict rotational error motions of the guidance module,a spatial redundant constraint is *** additive manufacturing technique is adopted to monolithically fabricate the proposed positioning *** simulation results show that the proposed XY positioning stage is capable to achieve ±2 x 2 mm2 working *** fabricated prototyping stage shows that the advanced manufactured flexure mechanism can achieve good geometric effect and could be a good alternative to a metal-based flexure mechanism.

关键词： Nanopositioning Beam flexure mechanism Additive manufacturing

来源：评论

学校读者我要写书评

暂无评论

Novel active damping control scheme for a three-phase active rectifier with LCL-filter

引用

Diangong Jishu Xuebao/Transactions of China Electrotechnical Society 2008年第9期23卷 86-91页

作者： Huang, Yuqi Jiang, Xinjian Qiu, Arui State Key Lab. of Security Control and Simulation of Power Systems and Large Generation Equipments Tsinghua University Beijing 100084 China

A novel active damping control scheme is developed to eliminate stability problems arisen in the current control of a three-phase voltage source active rectifier (VSR) with LCL-filter. A converter side inductance voltage feedback loop is introduced in the traditional voltage oriented control to stabilize VSR. A simplified discrete model including the current control loop and LCL-filter is established with one sample delay, considering time delays induced by S/H (sampling and holding), processing and modulation. The amplification coefficient of the converter side inductance voltage feedback loop is tuned up to change the unstable poles of LCL-filter. Parameter estimate methods are used to remove unnecessary sensors. simulation and experiment of VSR with LCL-filter demonstrate the proposed active damping control scheme and the stability analyses.

关键词： Inductance

来源：评论

学校读者我要写书评

暂无评论

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

请选择保存的检索档案：

请选择收藏分类：

通借通还

建议与咨询 留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

请选择保存的检索档案： 新增检索档案 确定 取消

请选择收藏分类： 新增自定义分类 确定 取消

通借通还

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

请选择保存的检索档案：

请选择收藏分类：