A physical model for mobility degradation by interface-roughness scattering and Coulomb scattering is proposed for SiGe p-MOSFET with a high-k dielectric/SiO2 gate stack. Impacts of the two kinds of scatterings on mob...
详细信息
A physical model for mobility degradation by interface-roughness scattering and Coulomb scattering is proposed for SiGe p-MOSFET with a high-k dielectric/SiO2 gate stack. Impacts of the two kinds of scatterings on mobility degradation are investigated. Effects of interlayer (SiO2) thickness and permittivities of the high-k dielectric and interlayer on carrier mobility are also discussed. It is shown that a smooth interface between high-k dielectric and interlayer, as well as moderate permittivities of high-k dielectrics, is highly desired to improve carriers mobility while keeping a low equivalent oxide thickness. Simulated results agree reasonably with experimental data.
WC- 10Co nanocomposite powder produced by spray pyrolysis-continuoas reduction and carbonization technology was used, and the vacuum sinteriag plus sinterhip process was cdopted to prepare ultrafine WCCo cemented carb...
详细信息
WC- 10Co nanocomposite powder produced by spray pyrolysis-continuoas reduction and carbonization technology was used, and the vacuum sinteriag plus sinterhip process was cdopted to prepare ultrafine WCCo cemented carbide. The microstructure, grain size, porosity, density, Rockwell A hardness （ HRA ）, transverse rupture strength （ TRS ） , saturated magnetization and coercivity force were studied. The experimental results show that average grain size of the sample prepared by vacuum sintering plas sinterhip technology was about 420 nm, transverse rupture strength was more than 3460 MPa, and Rockwell A hardness of sintered specimen was more than 92.5. Ultrafine WC- 10Co cemented carbide with high strength and high hardness is obtained.
Yttrium-filled sku, tterudites Yy Fex Co4-x Sb12 （ Y =0- 0. 40 ） were synthesized. The effect of Y filling fraction on thermoelectric properties of Yy Fex Co4-x Sb12 was investigated. All samples showed p-type condu...
详细信息
Yttrium-filled sku, tterudites Yy Fex Co4-x Sb12
（ Y =0- 0. 40 ） were synthesized. The effect of Y filling fraction on thermoelectric properties of Yy Fex Co4-x Sb12
was investigated. All samples showed p-type conduct. The electrical conductivity decreased with increasing filling fraction y. The Seebeck coefficient inreased with increasing temperature. The lattice thermal conductivity decreased with increasing filling fraction y and showed the minimum value at a certain filling fraction y = 0.3. The effect of different filling atoms M（ M： Ba, Ce, Y） on the lattice thermal conductivity of MyFexCo4-xSb12 was discussed. The maximum ZT value of O. 7 was obtained for Y0.06 Fe0.7 Co3.3 Sb12 at 750 K.
The rods that were shaped from nanocrystalline WC- 10.21 Co-0.42 VC/ Cr3 C2 （ wt% ） composite powders by using powder extrusion molding （PEM） were investigated. The nanocrystalline WC- 10.21 Co- 0. 42 VC/ Cr3 C2 ...
详细信息
The rods that were shaped from nanocrystalline WC- 10.21 Co-0.42 VC/ Cr3 C2 （ wt% ） composite powders by using powder extrusion molding （PEM） were investigated. The nanocrystalline WC- 10.21 Co- 0. 42 VC/ Cr3 C2 （ wt% ） composite powders were prepared by the spray thermal decomposition-continuous reduction and carburization technology. In order to improve the properties of rods shaped by using powder extrusion molding, the cold isostatic pressing （CIP） technology was used before or after debinding. Specimens were siutered by vacuum siutering and hot isostatic pressing （HIP）. The density, Rockwell A hardness, magnetic coercivity , and magnetic saturation induction of siutered specimen were measured. The microstructure of the green bodies and the siutered specimens was studied by scanning electron microscopy （SEM）. Results show that the rod formed by using powder extrusion molding after debinding and followed by cold isostatic pressing can be siutered to 99.5% density of composite cemented carbide rods with an average grain size of about 200- 300 nm, magnetic coercivity of 30.4 KA / m, Rockwell A hardness of 92.6 and magnetic saturation induction of 85% . Superfine WC- 10 Co cemented carbide rods with excellent properties were obtained.
SiCp/ Al composites containing high volume fraction of SiC particles were fabricated by spark plasma sintering （SPS）. and their thermophysical properties, such as thermal conductivity （TC） and *** of thermal expan...
详细信息
SiCp/ Al composites containing high volume fraction of SiC particles were fabricated by spark plasma sintering （SPS）. and their thermophysical properties, such as thermal conductivity （TC） and *** of thermal expansion （CTE）, were characterized. The electric field in the vacuum column was calculated and the generation condition of the spark was analyzed. Spark can be generated by a low current if the cavity in the green body is large enough. A high relative density of the composites was successfully achieved through the optimization of sintering parameters. The measured TCs of the SiCp/ Al composites fabricated by SPS are higher than 195 W/m ·K.
Both silica and boron-silica glass materials doped with terbium organic complex were prepared by in situ sol-gel method respectively. XRD and SEM measurements were performed to verify the non-crystalline structure of ...
详细信息
Both silica and boron-silica glass materials doped with terbium organic complex were prepared by in situ sol-gel method respectively. XRD and SEM measurements were performed to verify the non-crystalline structure of the glass. The influence of the glass contents on the structure of the glass and the erwrgy level of the doped Tb （Ⅲ） ions was analyzed by the emission spectra and IR spectra. The effect of B2O3 on the photolumirwscence properties of rare earth organic complex in silica- based glass was investigated. The IR spectra indicate that the in situ sylthesized rare earth complex molecule was confined to the micropores of the bost and the vibration of the ligands was frozen. When B2O3 was added into the silica host gel, B2O3 had little influence on the noncrystallirw structure of the glass, and BO3 triangle, which had a layer structure different from the silica framework, could form. So the silica network became more inhomogenous, and the luminescence of terbium complexes was quenched with the increase of the B2O23 amount.
BaCO3 whiskers exhibiting different morphologies were fabricated by a simple precipitation reaction of barium ch/oride with sodium carbonate in the absence and presence of poly-（styrene-alt-maleic acid） （PSMA） as ...
详细信息
BaCO3 whiskers exhibiting different morphologies were fabricated by a simple precipitation reaction of barium ch/oride with sodium carbonate in the absence and presence of poly-（styrene-alt-maleic acid） （PSMA） as a crystal growth modifier at room temperature. The as-prepared products were characterized by scanning electron microscopy （SEM）, transmission electron microscopy （TEM）, and X-ray diffraction （XRD）. The influences of experimental parameters on the size and morphology of BaCO3 whiskers were investigated and discussed. It was found that the as-prepared BaCO3 whiskers are single crystals with diameter ranging from 100 to 300 run, and grow along the crystallographic a-axis or [100] direction. BaCO3 whiskers with different morphologies, such as branching and dendritic structure, can be obtained depending on the experimental conditions. With increasing PSMA concentration, the diameter of BaCO3 whiskers decreases.
Novel ordered mesoporous Eu(DBM)3phen/APTES-SBA-15 (EAS) composites with reasonable photoluminescence property and interesting morphology of bundles of pearl-like chains were synthesized. The characteristics of the me...
详细信息
Novel ordered mesoporous Eu(DBM)3phen/APTES-SBA-15 (EAS) composites with reasonable photoluminescence property and interesting morphology of bundles of pearl-like chains were synthesized. The characteristics of the mesostructure and the optical properties of the prepared samples were investigated by means of XRD, FTIR, SEM, TEM, N2 adsorption–desorption and PL spectroscopy. The results indicate that the as-made EAS composites have long-distance ordered mesoporous structure. Compared with the Eu(DBM)3phen complex, it is found that the EAS composites perform a considerable photoluminescence with good color purity. It is proposed that the anchored amine from the APTES and quantum size effect of the Eu(DBM)3phen complex have great effect on the photoluminescence of the EAS composites.
Ordered iron fiber arrays were electrodeposited on the surface of zinc foils using ＂FeSO4 solution-sodium caprylate-Decanol＂ 3-component reverse hexagonal liquid crystal as soft templates. The structure of the soft ...
详细信息
Ordered iron fiber arrays were electrodeposited on the surface of zinc foils using ＂FeSO4 solution-sodium caprylate-Decanol＂ 3-component reverse hexagonal liquid crystal as soft templates. The structure of the soft templates and the synthesized iron ,fibers were characterized by polarizing microscopy, X-ray diffraction （XRD）, scanning electron microscopy （SEM） and energy dispersive X-ray microanalysis etc. The experimental results shou that the synthesized iron fibers with a crystal phase grew up in the form of fiber clusters of about 200 nm along the direction perpendicular to the cathode surface. Each cluster was composed of several tens of fibers. The fibers had almost the same length of more than 10μm with a diameter of about 50 nm.
Pulse current heating (PCH) was used to join Ti-6Al-4V alloy at two cases of with die and without die. Hot-pressing (HP) method was used to provide a comparison between the two methods. Microstructures near the contac...
详细信息
Pulse current heating (PCH) was used to join Ti-6Al-4V alloy at two cases of with die and without die. Hot-pressing (HP) method was used to provide a comparison between the two methods. Microstructures near the contacting surfaces were observed in optical microscope. Temperature distribution was analyzed. After joining, the tensile properties of the samples were evaluated. Experimental results show that grains and phases grow transversely on contacting surfaces, which makes two parts into a whole with a certain of tensile strength. PCH joining is a different temperature joining method. The highest temperature is located at the interface. The comparison of tensile strengths of samples joined by the two methods indicates that joining temperature and holding time needed by PCH are lower and less than those needed for HP.
暂无评论