检索结果-内蒙古大学图书馆

Strengthening and toughening mechanisms of martensite-bainite microstructure in 2 GPa ultra-high strength steel during hot stamping

引用

Science China Technological Sciences 2025年第5期68卷 19-33页

作者： Yanli SONG Ye LI Jue LU Lin HUA Yanfeng GU Yikuan YANG Hubei Key Laboratory of Advanced Technology for Automotive Components Wuhan University of Technology State Key Laboratory of Advanced Technology for Materials Synthesis and Processing Wuhan University of Technology

In response to the growing demand for energy efficiency, safety, and lightweight designs in new energy vehicles, this study addresses the challenge of balancing strength and toughness in ultra-high strength steel(UHSS) components produced by hot stamping. An innovative hot stamping process based on a martensite-bainite(M-B) complex-phase microstructure was proposed to enhance the strength and toughness of UHSS. The microstructural evolution of the M-B complexphase during the hot stamping process was investigated using commercial B1800HS steel. With a microstructure consisting of 87.4.% martensite, 8.7% lower bainite, and 3.9% film-like retained austenite by volume fraction, the steel achieved a tensile strength of 1944 MPa, total elongation of 9.66%, and impact energy of 25.8 J. Compared with conventional hot stamping, the strength of the material showed only a slight improvement, whereas elongation and impact energy were enhanced by approximately 53% and 32%, respectively. A quantitative relationship among process parameters, resulting microstructure, and mechanical properties was established. Optimization between strength and toughness was observed when the low bainite volume fraction ranged from 5.06% to 8.73%. The toughening mechanisms are attributed to the refinement of martensite lath bundles(width of 202 nm) facilitated by bainite formation, the increase in high-angle grain boundaries, and the presence of nanoscale retained austenite(width of 80 nm) between the laths. Additionally, the refinement of grains and the formation of nanoscale(Nb, Ti)C precipitates(diameter of 17 nm) further contributed to the overall strength. The developed M-B complexphase process, which involves medium-temperature slow cooling followed by rapid low-temperature quenching, provides an optimal combination of strength and toughness for a wide range of applications.

关键词： ultra-high strength steel hot stamping strengthening and toughening mechanisms martensite-bainite complex-phase microstructure

来源：评论

学校读者我要写书评

暂无评论

Degradation mechanism,direct regeneration and upcycling of ternary cathode material for retired lithium-ion power batteries

引用

Journal of Energy Chemistry 2025年第3期102卷 534-554页

作者： Juan Wang Dongqi Li Weihao Zeng Xingye Chen Yixin Zhang Shaojie Zhang Zhongpeng Li Changhao Li Shichun Mu State Key Laboratory of Advanced Technology for Materials Synthesis and Processing Wuhan University of TechnologyWuhan 430070HubeiChina

With the approaching of large-scale retirement of power lithium-ion batteries(LIBs),their urgent handling is required for environmental protection and resource ***,at present,substantial spent power batteries,especially for those high recovery value cathode materials,have not been greenly,sustainably,and efficiently *** to the traditional recovery method for cathode materials with high energy consumption and severe secondary pollution,the direct repair regeneration,as a new type of short-process and efficient treatment methods,has attracted widespread ***,it still faces challenges in homogenization repair,electrochemical performance decline,and scaling-up *** promote the direct regeneration technology development of failed NCM materials,herein we deeply discuss the failure mechanism of nickel-cobalt-manganese(NCM)ternary cathode materials,including element loss,Li/Ni mixing,phase transformation,structural defects,oxygen release,and surface degradation and *** on this,the detailed analysis and summary of the direct regeneration method embracing solid-phase sintering,eutectic salt assistance,solvothermal synthesis,sol-gel process,spray drying,and redox mediation are ***,the upcycling strategy for regeneration materials,such as single-crystallization and high-nickelization,structural regulation,ion doping,and surface engineering,are discussed in ***,the challenges faced by the direct regeneration and corresponding countermeasures are pointed ***,this review provides valuable guidance for the efficient and high-value recovery of failed cathode materials.

关键词： Spent NCM materials Retired lithium-ion power battery Degradation mechanism Direct regeneration Upcycling strategy

来源：评论

学校读者我要写书评

暂无评论

Effect of Molecular Weight on Thermoelectric Performance of P3HT Analogues with 2-Propoxyethyl Side Chains

引用

Journal of Wuhan University of technology(materials Science) 2024年第2期39卷 268-281页

作者：董得福 WANG Wei ZHAN Chun LI Chenglong ZHOU Qisheng 肖生强 State Key Laboratory of Advanced Technology for Materials Synthesis and Processing Wuhan University of TechnologyWuhan 430070China

By replacing hexyl chains in poly(3-hexylthiophene)(P3HT)with 2-propoxyethyls,four poly(3-(2-propoxyethyl)thiophene)(P3POET)homopolymers with comparable polydispersity indexes(PDI)and regioregularities were prepared herein in addition with step increment of about 7 kDa on numberaverage molecular weight(M_(n))from around 11 to 32 kDa(accordingly denoted as P11k,P18k,P25k,and P32k).When doped in film by FeCl_(3)at the optimized conditions,the maximum power factor(PF_(max))increases greatly from 4.3μW·m^(-1)·K^(-2)for P11k to 8.8μW·m^(-1)·K^(-2)for P18k,and further to 9.7μW·m^(-1)·K^(-2)for P25k,followed by a slight decrease to 9.2μW·m^(-1)·K^(-2)for *** close Seebeck coefficients(S)at PF_(max)are observed in these doped polymer films due to their consistent frontier orbital energy levels and Fermi *** main contribution to this PF_(max)evolution thus comes from the corresponding conductivities(σ).Theσvariation of the doped films can be rationally correlated with their microstructure evolution.

关键词： conjugated polymer molecular weight microstructure thermoelectric performance

来源：评论

学校读者我要写书评

暂无评论

Control of interfacial reaction and defect formation in Gd/Bi_(2)Te_(2.7)Se_(0.3) composites with excellent thermoelectric and magnetocaloric properties

引用

Chinese Physics B 2024年第8期33卷 474-481页

作者：薛天畅魏平刘承姗李龙舟朱婉婷聂晓蕾赵文俞 State Key Laboratory of Advanced Technology for Materials Synthesis and Processing Wuhan University of TechnologyWuhan 430070China

The method to combine thermoelectric(TE)and magnetocaloric(MC)cooling techniques lies in developing a new material that simultaneously possesses a large TE and good MC cooling *** this work,using n-type Bi_(2)Te_(2.7)Se_(0.3)(BTS)as the TE base material and Gd as the second-phase MC material,Gd/BTS composites were prepared by the spark plasma sintering *** the composites,interfacial reaction between Gd and BTS was identified,resulting in the formation of Gd Te,which has a large impact on the electron concentration through the adjustment of defect *** MC/TE composite containing 2.5 wt%Gd exhibited a ZT value of 0.6 at 300 K,essentially retaining the original TE performance,while all the composites largely maintained the excellent MC performance of *** work provides a potential pathway to achieving high performance in MC/TE composites.

关键词： thermo-electro-magnetic energy conversion materials interfacial reaction thermoelectric performance magnetic entropy change

来源：评论

学校读者我要写书评

暂无评论

Microstructure Regulation and Combustion Performance Optimization of PVDF/Al Composite Powder by Non-covalent Functionalized Graphenes

引用

Journal of Wuhan University of technology(materials Science) 2024年第4期39卷 904-911页

作者：易卓然 DENG Haoyuan QIN Mei 孙一 LUO Guoqiang State Key Laboratory of Advanced Technology for Materials Synthesis and Processing Wuhan University of TechnologyWuhan 430070China

Graphene prepared by non-covalent modification of sulfonated poly(ether-ether-ketone)(SPG)was combined with polyvinylidene fluoride(PVDF)/Al to improve the PVDF/Al thermal conductivity while reducing the effect of the thermal resistance at the graphene-polymer *** regulation rule of SPG with different contents on the energy release of fluorine-containing system was *** the content of SPG is 4%,the peak pressure and rise rate of SPG/PVDF/Al composite powder during ignition reach the maximum of 4845.28 kPa and 8683.58 kPa/*** the content of SPG is 5%,the PVDF/Al composite powder is completely coated by SPG,and the calorific value of the material reachs the maximum of 29.094 kJ/*** the design and micro-control of the composite powder,the calorific value of the material can be effectively improved,but the improvement of the mass release rate still depends on the graphene content and surface modification state.

关键词： energetic materials PVDF/Al composites graphene modification energy release combustion

来源：评论

学校读者我要写书评

暂无评论

Ultrastrong MXene film bridged by liquid metal

引用

Science China materials 2024年第12期67卷 4115-4116页

作者： Zhengyi Fu State Key Laboratory of Advanced Technology for Materials Synthesis and Processing Wuhan University of TechnologyWuhan 430070China

Two-dimensional(2D)titanium carbide(Ti_(3)C_(2)T_(x))MXene nanosheets show promising mechanical and electrical properties,indicating great potential applications in aerospace and electronic devices,etc.[1,2].There are many assembling approaches including vacuum filtration,blade coating and layer-by-layer[3–5].However,it still remains a great challenge to realize the intrinsic performance of MXene nanosheets into macroscopic film due to low stress transfer efficiency,which usually is indued by the voids and misalignment during the assembling process[6].Thus,it remains a great challenge to assemble MXene nanosheets into high-performance macroscopic MXene films.

关键词： carbide coating film

来源：评论

学校读者我要写书评

暂无评论

Thermal Stability and Degeneration Behavior of Solar Selective Absorber Based on WTi-Al_(2)O_(3)Cermet

引用

Journal of Wuhan University of technology(materials Science) 2024年第6期39卷 1555-1564页

作者： WANG Xiaobo FANG Wei MA Yuchao CHENG Xudong LI Kewei Department of Physics and Electronic Engineering Jinzhong UniversityJinzhong 030619China College of Materials Science and Engineering Taiyuan University of TechnologyTaiyuan 030024China State Key Laboratory of Advanced Technology for Materials Synthesis and Progressing Wuhan University of TechnologyWuhan 430070China

A WTi-Al_(2)O_(3)cermet-based solar selective absorber was prepared to investigate the atomic diffusion induced spectral selectivity *** as-deposited coating exhibits superior absorptance(0.934)and low thermal emittance(0.098),as well as excellent thermal stability with a selectivity of 0.900/0.07 even after annealing at 923 K for 400 h in Ar ***,the multilayer coating failed after being subjected to annealing at 923 K for 400 h in an air environment,as indicated by a decrease in solar absorptance to 0.912 and an increase in thermal emittance to *** microstructure characterizations reveal that the annealed coating exhibits a columnar morphology along the vertical direction of the *** presence of abundant grain boundaries in the multilayer coating promotes the outward diffusion of Cr and Mn atoms in the stainless-steel *** Mn atoms,in particular,possess the capability to migrate towards the surface of the coating and undergo an oxidation reaction with oxygen,facilitating the formation of a thick Mn_(2)O_(3)*** roughness of the coating surface was significantly increased in this case,adversely affecting solar absorptance due to amplified sunlight *** addition,the rocketing of thermal emittance is attributed to the destabilization of W infrared reflective layer during the *** findings highlight the importance of considering the outward diffusion of Mn and Cr elements in the stainless-steel substrate when optimizing solar selective absorbers.

关键词： solar selective absorber thermal stability spectral selectivity optical properties

来源：评论

学校读者我要写书评

暂无评论

Bioprocess inspired formation of calcite mesocrystals by cation-mediated particle attachment mechanism

引用

National Science Review 2023年第4期10卷 159-168页

作者： Qihang Wang Bicheng Yuan Wenyang Huang Hang Ping Jingjing Xie Kun Wang Weimin Wang Zhaoyong Zou Zhengyi Fu State Key Laboratory of Advanced Technology for Materials Synthesis and Processing Wuhan University of Technology Hubei Longzhong Laboratory

Calcite mesocrystals were proposed, and have been widely reported, to form in the presence of polymer additives via oriented assembly of nanoparticles. However, the formation mechanism and the role of polymer additives remain elusive. Here, inspired by the biomineralization process of sea urchin spine comprising magnesium calcite mesocrystals, we show that calcite mesocrystals could also be obtained via atachment of amorphous calcium carbonate(ACC) nanoparticles in the presence of inorganic zinc ***, we demonstrate that zinc ions can induce the formation of temporarily stabilized amorphous nanoparticles of less than 20 nm at a significantly lower calcium carbonate concentration as compared to pure solution, which is energetically beneficial for the atachment and occlusion during calcite growth. The cation-mediated particle atachment crystallization significantly improves our understanding of mesocrystal formation mechanisms in biomineralization and offers new opportunities to bioprocess inspired inorganic ions regulated materials fabrication.

关键词： nonclassical crystallization mesocrystal calcium carbonate zinc ion particle attachment

来源：评论

学校读者我要写书评

暂无评论

Origin of shear induced‘catching bonds’on half Heusler thermoelectric compounds XFeSb(X=Nb,Ta)and SnNiY(Y=Ti,Zr,Hf)

引用

npj Computational materials 2024年第1期10卷 2607-2614页

作者： Haoqin Ma Xiege Huang Zhongtao Lu Xiaobin Feng Bo Duan Wenjuan Li Yinhan Liu Pengcheng Zhai Guodong Li Qingjie Zhang Hubei Key Laboratory of Theory and Application of Advanced Materials Mechanics School of ScienceWuhan University of Technology430070 WuhanChina State Key Laboratory of Advanced Technology for Materials Synthesis and Processing Wuhan University of Technology430070 WuhanChina

Half Heusler materials exhibit excellent thermoelectric and mechanical properties,rendering them potential candidates for advanced thermoelectric ***,the developments on interrelated devices are impeded by their inherent brittleness and limited ***,it exists the potential ductility on half Heusler materials with face-centered cubic sub-lattices through the expectation of the occurrence of shear-induced‘catching bonds’which can result in excellent ductility on other face-centered cubic materials.

关键词： ductility cubic rendering

来源：评论

学校读者我要写书评

暂无评论

Effect of Composite Composition on the Contact Angle of B_(4)C-xTiB_(2)/Cu

引用

Journal of Wuhan University of technology(materials Science) 2024年第5期39卷 1116-1120页

作者： HU Dong ZHANG Xin ZHANG Jinyong LEI Liwen State Key Laboratory of Advanced Technology for Materials Synthesis and Processing Wuhan University of TechnologyWuhan 430070China Hubei Key Laboratory of Theory and Application of Advanced Materials Mechanics Wuhan University of TechnologyWuhan 430070China

The wetting behavior of molten Cu on the B_(4)C-xTiB_(2)ceramic composites was investigated in this *** results show that the contact angle of molten Cu alloy on B_(4)C-TiB_(2)ceramic composites is linear with the composition rate of TiB_(2)or B_(4)C while the temperature is in the range of 1300 to 1350℃,consistent with the expectation of the commonly used theoretical ***,a nonlinear relationship between the contact angle and the composition rate unexpectedly occurred at temperatures ranging from 1400 to 1500℃.The big difference of the contact angles between the molten metal and the components in the composites was found to be the key *** result identifies that the commonly used theoretical method only works at a limited difference of the contact angle of the liquid on the different phases in the composites,and fails at a big difference.

关键词： wetting B_(4)C-TiB_(2) composites interfacial reaction

来源：评论

学校读者我要写书评

暂无评论

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

请选择保存的检索档案：

请选择收藏分类：

通借通还

建议与咨询 留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

请选择保存的检索档案： 新增检索档案 确定 取消

请选择收藏分类： 新增自定义分类 确定 取消

通借通还

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

请选择保存的检索档案：

请选择收藏分类：