检索结果-内蒙古大学图书馆

2020 IEEE Sustainable power and Energy Conference, iSPEC 2020

作者： Wang, Conghui Tian, Liting Zhang, Fang Cheng, Lin School of Electrical Engineering Beijing Jiaotong University Beijing China State Key Laboratory of Control and Simulation of Power Systems and Generation Equipment Tsinghua University Beijing China

ISBN: (纸本)9781728191645

This paper focuses on optimal sizing of photovoltaic (PV) and battery energy storage system (BESS) of special-use charging station for electric taxi cabs. Aiming to minimize annual equivalent cost of the charging station under two-part electricity pricing mechanism, an optimal sizing algorithm of PV and BESS is established considering the randomness of PV output and the power constraint of the grid, as well as whether charging station participates in demand response (DR). The cooperative operation strategies of charging facilities, PV and BESS under typical scenarios are proposed. Considering the factors that affect the optimal results, this paper provides sensitivity analysis in a charging station. Finally, the proposed optimal sizing algorithm is verified in the charging station equipped with 24 EV charging piles, and the economic analysis of the optimal sizing scheme is carried out. Based on economical analysis of optimal sizing results, it is found out that the equivalent cost of EV charging station is lower when participating in demand response. The results show that the annual equivalent total cost of the charging station is significantly reduced under the new optimal sizing scheme. © 2020 IEEE.

关键词： Sensitivity analysis

来源：评论

学校读者我要写书评

暂无评论

simulation and feature extraction of inter-shaft bearing fault in rotor-bearing-casing system 26

Simulation and feature extraction of inter-shaft bearing fau...

引用

26th International Congress on Sound and Vibration, ICSV 2019

作者： Yang, Yizhou Liu, Chao Jiang, Dongxiang Han, Te State Key Lab of Control and Simulation of Power Systems and Generation Equipment Department of Thermal Engineering Tsinghua University Beijing100084 China

ISBN: (纸本)9781999181000

The inter-shaft bearing could simplify the supporting structure of a dual-rotor system, so it is widely used in rotating machinery like gas turbine engine. When monitoring the vibration of an inter-shaft bearing, sensors usually could not be installed inside the engine because of the compact structure, then will be installed on the casing. The vibration of the inter-shaft bearing will be transmitted though both the two rotors to the supporting bearings then to the casing, and both the inner and outer ring rotate, making the condition monitoring much more difficult than normal bearings. In this paper, a dual-rotor system dynamic model with the rotor-bearing-casing structure is built to simulate the vibration of an inter-shaft bearing. The rotors and the casing are modelled using finite element method and the bearings are modelled using a nonlinear multi-body dynamic model. The normal state of the inter-shaft bearing is simulated, then the bearing fault states with localized defects on the inner race, the outer race and one of the rolling elements are simulated. Signal processing methods are utilized to extract bearing fault features from the casing vibration acceleration signal. Besides the fixed rotating speed condition, rotors under variable speeds are also simulated, then the vibration signal and fault feature become more complex and the signal analysis becomes a bigger challenge © Proceedings of the 26th International Congress on Sound and Vibration, ICSV 2019. All rights reserved.

关键词： Dynamic models

来源：评论

学校读者我要写书评

暂无评论

Modeling and Analysis of Unit Commitment Considering RCAES System 33

Modeling and Analysis of Unit Commitment Considering RCAES S...

引用

第三十三届中国控制会议

作者： LIU Bin CHEN Laijun ZHANG Yu FANG Chen MEI Shengwei ZHOU Yuan State Key Lab of Control and Simulation of Power Systems and Generation Equipment Department of Electrical EngineeringTsinghua University Electric Power Research Institute State Grid Shanghai Municipal Electric Power Company Key Laboratory of Cryogenics Technical Institute of Physics and ChemistryChinese Academy of Sciences

ISBN: (纸本)9781479947249

Regenerative compressed air energy storage(RCAES) system is a practical and efficient solution to large-scale integration of renewable energy problems faced by power systems currently. Appropriately modeling of RCAES system is critical to its practical application, whereas research in this area has been very limited. According to the energy storage and transformation process, a concise model of RCAES system applicable to power scheduling field is proposed. Then, a unit commitment model with RCAES system is formulated as a MILP problem which can be accurately solved with high computation efficiency by CPLEX. A modified IEEE 39 bus system is used to study the impacts of parameters of RCAES system on unit commitment and the effectiveness of the proposed model is then validated. Furthermore, the proposed model can also be employed to optimize key parameters of RCAES system, e.g. efficiency and capacity of each part in an integrated way.

关键词： unit commitment,regenerative,CAES,efficiency analysis,schedule

来源：评论

学校读者我要写书评

暂无评论

Design, simulation and analysis of the low stray inductance bus bar for voltage source inverters

Design, simulation and analysis of the low stray inductance ...

引用

2011 International Conference on Electrical Machines and systems, ICEMS 2011

作者： Yuan, Liqiang Yu, Hualong Wang, Xuesong Zhao, Zhengming State Key Laboratory of Control and Simulation of Power System and Generation Equipment Department of Electrical Engineering Tsinghua University Beijing 100084 China

ISBN: (纸本)9781457710445

Hard-switching technique under the high voltage and high current is one of main trends of high power inverters. Under this switching mode, the stray parameters of the commutating loops, especially the stray inductance of the DC bus bar, have significant influence on the switching process, electromagnetic interference and component stress of the semiconductor switches. It becomes one of the key points for the safe operation of inverters. Based on an actual 55kW inverter, the design, simulation and analysis for its bus bar is described in this paper. The bus bar model is built with the method of Partial Element Equivalent Circuit (PEEC), and the stray parameters are extracted from PEEC model and applied in the circuit simulation. Compared with the experimental results, the modeling validity is proved, and the simplified modeling process and design principles for complex physical bus bar are presented. © 2011 IEEE.

关键词： Circuit simulation

来源：评论

学校读者我要写书评

暂无评论

Convolution Neural Network-based Load Model Parameter Selection Considering Short-term Voltage Stability

引用

CSEE Journal of power and Energy systems 2024年第3期10卷 1064-1074页

作者： Ying Wang Chao Lu Xinran Zhang School of Technology Beijing Forestry UniversityBeijing 100083China State Key Laboratory of Control and Simulation of Power System and Generation Equipment Tsinghua UniversityBeijing 100084China School of Automation Science and Electrical Engineering Beihang UniversityBeijing 100083China IEEE

The recently proposed ambient signal-based load modeling approach offers an important and effective idea to study the time-varying and distributed characteristics of power ***,it also brings new *** the load model parameters of power loads can be obtained in real-time for each load bus,the numerous identified parameters make parameter application *** order to obtain the parameters suitable for off-line applications,load model parameter selection(LMPS)is first introduced in this ***,the convolution neural network(CNN)is adopted to achieve the selection purpose from the perspective of short-term voltage *** begin with,the field phasor measurement unit(PMU)data from China Southern power Grid are obtained for load model parameter identification,and the identification results of different substations during different times indicate the necessity of ***,the simulation case of Guangdong power Grid shows the process of LMPS,and the results from the CNNbased LMPS confirm its effectiveness.

关键词： Ambient signal CNN field PMU data load model parameter selection short-term voltage stability

来源：评论

学校读者我要写书评

暂无评论

A systematic and qualitative assessment method and software design for energy efficiency of typical electric machine systems with pumps and fans

A systematic and qualitative assessment method and software ...

引用

11th International Conference on Electrical Machines and systems, ICEMS 2008

作者： Yi, Lei Zhengming, Zhao Jing, Xue State Key Laboratory of Control and Simulation of Power System and Generation Equipment Department of Electrical Engineering Tsinghua University Beijing 100084 China

ISBN: (纸本)9787506292214

Three-phase induction motors as well as power converters are intrinsically efficient machines and devices. However, due to the common misapplication of them with loads like pumps and fans, these electric machine systems are considered a great potential of energy conservation in industries. As to assessing methods of energy conservation, neither the study of induction machine efficiency nor the analysis of pumps and fans performance is new. However, the systematic and qualitative analysis and assessment of the energy efficiency of induction machines, loads and control devices acting as a whole system are still complicated yet indispensable for electric machine system energy conservation program in China. In this paper, a systematic and qualitative assessment method for energy application efficiency of electric machine system is raised. Based on this method, an assessing computer program is designed to provide referencing information for making investment decisions regarding energy efficiency measures at manufacturing plants. An expert system is also designed to choose equipments that match each other.

关键词： Investments

来源：评论

学校读者我要写书评

暂无评论

A predictive DC voltage control scheme for back-to-back converters based on energy balance modeling

A predictive DC voltage control scheme for back-to-back conv...

引用

2011 International Conference on Electrical Machines and systems, ICEMS 2011

作者： Yin, Lu Zhao, Zhengming Lu, Ting He, Fanbo Yuan, Liqiang State Key Laboratory of Control and Simulation of Power System and Generation Equipment Department of Electrical Engineering Tsinghua University Beijing 100084 China

ISBN: (纸本)9781457710445

This paper presents a predictive control scheme of DC-link voltage for back-to-back converters based on energy balance modeling. Since the variation of DC-link voltage is affected by the energy mismatch between rectifier and inverter, the energy distribution in a rectifier-inverter is analyzed. Moreover, in order to calculate the input and output energy in one control period accurately, the grid current is regulated by predictive control and the instantaneous active power consumed by the induction motor is estimated. Then, an equation based on energy balance in one control period is established, and the DC-link voltage can be controlled by solving it. Finally, simulation results show that with the proposed control scheme, the back-to-back converter exhibits both good dynamic and steady-state performances. © 2011 IEEE.

关键词： Energy balance

来源：评论

学校读者我要写书评

暂无评论

Optimal design of the back-to-back IGBT-based converter with the concept of systematic safe operating area

Optimal design of the back-to-back IGBT-based converter with...

引用

2011 International Conference on Electrical Machines and systems, ICEMS 2011

作者： Zou, Gaoyu Zhao, Zhengming Yuan, Liqiang Wang, Xuesong Lu, Ting State Key Laboratory of Control and Simulation of Power System and Generation Equipment Department of Electrical Engineering Tsinghua University Beijing 100084 China

ISBN: (纸本)9781457710445

The key parameters of SOA (safe operating area) of semiconductor devices are hard to be measured when converter is operating, which is not helpful to protect converter at any time. On the other hand, surplus estimating method is widely used to design the main circuit. In order to guarantee the whole system works safely and improve utilization rate of devices, the concept of SSOA (systematic safe operating area) is presented. By determining the relationship of key parameters between devices and converter, the expression of SSOA is described quantitatively. Then it is implemented as a basic rule to design a back-to-back converter based on IGBT for 55kW induction motor optimally. Rated value of DC-link voltage and grid filter of the system is obtained reasonably as well. © 2011 IEEE.

关键词： Insulated gate bipolar transistors (IGBT)

来源：评论

学校读者我要写书评

暂无评论

Nonlinear E-field simulation of HVDC Converter Transformer Busing and Its Structure Optimization With RBF Neural Network and NSGA-II Algorithm 13

Nonlinear E-field Simulation of HVDC Converter Transformer B...

引用

13th International Conference on power and Energy systems, ICPES 2023

作者： He, Yongsheng Zhang, Shiling Lu, Zongxiang Wang, Pengbo State Grid Chongqing Electric Power Company Chongqing Electric Power Research Institute Chongqing China State Key Lab of Control and Simulation of Power Systems and Generation Equipment Haidian China Transmission Equipment and System Security and New Technology Dept Name of State Key Laboratory of Power Chongqing China

ISBN: (纸本)9798350345063

Static DC and PR are typical operation conditions of HVDC converter transformer bushing outlet device, moreover, the electrical parameters of RIP, transformer oil and OIP have the nonlinear relationship with E-field stress and temperature. Under the temperature gradient, the electrical parameters will modify the static DC and PR E-field distribution of the composite insulation. In order to simulate static DC and PR electric field of the composite insulation structure, this paper established the full model of the converter transformer outlet. Then, the structure parameters of converter transformer outlet have been optimized using combined RBF neural network and NSGA-II algorithm. Moreover, electric field verification calculation has been carried out under AC and PR conditions. The results show that under uniform temperature condition, E-field strength is larger than that under iso-thermal condition. The overshoot coefficient of the bushing end and barrier reach 65% and 45%, respectively. The study can provide reference for the design of outlet structure of the converter transformer. © 2023 IEEE.

关键词： DC transformers

来源：评论

学校读者我要写书评

暂无评论

A computer control and monitoring system for high power converters

A computer control and monitoring system for high power conv...

引用

ICEMS 2005: 8th International Conference on Electrical Machines nd systems

作者： Rong, Yi Zhenming, Zhao Xiaoying, Sun Liqiang, Yuan Jue, Qian Department of Electrical Engineering State Key Laboratory of Control and Simulation of Power System and Generation Equipment Tsinghua University Beijing 100086 China

ISBN: (纸本)7506274078

Computer control and monitoring system (CCMS) is quite important for high power converters (HPCs) operation. This paper presents a novel CCMS, which integrates a database management system (DBMS) into the monitoring software to get the beneficial features such as simple configuration and compact structure. In its communication system, an advanced optical fiber communication (OFC) technology is applied and priority-based communications is proposed to improve the reliability and the real time of the communications. Furthermore, a friendly standard Windows human-machine interface (HMI) is provided. The reliability and performance of the system are verified by system tests and practical operations.

关键词： power converters

来源：评论

学校读者我要写书评

暂无评论

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

请选择保存的检索档案：

请选择收藏分类：

通借通还

建议与咨询 留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

请选择保存的检索档案： 新增检索档案 确定 取消

请选择收藏分类： 新增自定义分类 确定 取消

通借通还

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

请选择保存的检索档案：

请选择收藏分类：