检索结果-内蒙古大学图书馆

Simulation Study on Hydrogen-Heating-Power Poly-Generation System based on Solar Driven Supercritical Water Biomass Gasification with Compressed Gas Products as an Energy Storage System

学校读者我要写书评

暂无评论

Journal of Thermal Science 2020年第2期29卷 365-377页

作者： JIN Hui WANG Cui FAN Chao State Key Laboratory of Multiphase Flow in Power Engineering Xi'an Jiaotong UniversityXi'an 710049China

Supercritical water gasification driven by solar energy is a promising way for clean utilization of biomass with high moisture content, but direct discharge of liquid residual causes energy waste and decreases energy efficiency. To reduce energy waste, a poly-generation system for hydrogen-rich gas production coupling heat supply and power generation based on supercritical water gasification of biomass driven by concentrated solar energy was established in this paper, which also provided a novel energy storage method to overcome the shortcomings of solar discontinuity. Thermodynamic model of the system was proposed and life cycle assessment(LCA) of the system was conducted. Influence of different parameters(temperature of 600℃ to 800℃, outlet temperature of heat exchanger of 42℃ to 56℃, biomass slurry concentration of 5% to 6.5%) on the gasification performance, energy and exergy efficiency, energy distribution and global warming potential(GWP) was discussed. The results indicated that hydrogen yield increased as gasification temperature increased since free radical reaction was enhanced which gas production reaction was classified into. Molar fraction of hydrogen increased as gasification temperature increased and reached 65.6% at 750℃. Energy and exergy efficiency of the system reached 74.84% and 34.87% at 700℃ and 600℃ respectively and that of gas production was 18.15% at 650℃, which was the highest. Increasing reaction temperature and decreasing biomass slurry concentration were effective ways to decrease GWP. Optimal operating parameter was reaction temperature of 650℃, outlet temperature of heat exchanger of 50℃ and biomass concentration of 5%.

关键词： biomass supercritical water gasification poly-generation system thermodynamics analysis energy storage life cycle assessment

Molecular dynamics revealing the non-monotonic variation of oil–water interfacial tension under the effect of cations and asphaltenes

学校读者我要写书评

暂无评论

Journal of Molecular Liquids 2025年 431卷

作者： Zhang, Faxue Wen, Boyao Lu, Xi Wang, Haibo Luo, Zhengyuan Bai, Bofeng State Key Laboratory of Multiphase Flow in Power Engineering Xi'an Jiaotong University Shaanxi Xi'an710049 China Petroleum Exploration and Production Research Institute of Sinopec Beijing China

The cations can significantly affect the interfacial dynamics of asphaltene molecules, which greatly change the mechanics of oil–water interfaces and thus have a remarkable impact on the chemical flooding process of heavy oil. However, Due to the weak amphiphilic property of asphaltene, the effects of cations on the interfacial behaviors of asphaltene as well as the interfacial mechanics are still unclear. Here, we study the effects of different types and concentrations of cations (Na+, Ca2+ and Mg2+) on the interfacial tension of oil–water systems with different asphaltenes (C5Pe) concentrations by using molecular dynamics simulations. As asphaltene concentration rises, the stronger interactions between cation and asphaltene induce an interfacial enrichment of asphaltenes, resulting in a decrease of interfacial tension. The cations have a more prominent impact on the interfacial tension when the oil–water interfaces reach supersaturated adsorption state of asphaltene molecules. The interfacial tension shows a non-monotonic variation with cation concentration increasing, which has a minimum at intermediate cation concentrations in our simulations. We explain this non-monotonic dependence of interfacial tension on cation concentration by a coupling effect of cations and asphaltene molecules. Under low cation concentrations, the interaction between cations and asphaltenes gradually enhances with cation concentration increasing, leading to a weaker π–π interaction between asphaltenes. Consequently, the asphaltene aggregates disperse and individual asphaltene molecules can easily migrate to the interface. The surface density of asphaltene thus increases, causing a reduction in interfacial tension. At high cation concentrations, cations strongly shield the electrostatic attraction between asphaltene and water molecules, so that the adsorption ability of asphaltenes at interface will weaken or even desorb, thus the interfacial tension elevate. Our results reveal the under

关键词： Adsorption Aggregation Asphaltenes Cations Interfacial tension Molecular dynamics

Hydrodynamic Interaction of Two Droplets Covered with Insoluble Surfactant in Shear flow

学校读者我要写书评

暂无评论

SSRN 2023年

作者： Wei, Wei Luo, Zhengyuan Bai, Bofeng State Key Laboratory of Multiphase Flow in Power Engineering Xi’an Jiaotong University Xi’an710049 China

Despite its significance in various applications, e.g., droplet microfluidics and enhancing oil recovery, the effects of surfactants on the hydrodynamic interactions of droplets in shear flow still need to be clarified. This paper presents a systematic investigation on the hydrodynamic interaction of two droplets covered with the insoluble surfactant in a simple shear flow, which is realized by using our own three-dimensional front-tracking code. Our results indicate that surfactants significantly affect the hydrodynamic interactions of droplets, characterized by the maximum deviation in the z-direction and the shear-induced self-diffusion. Then we examine the effects of surfactant-relevant parameters, i.e., the surface Peclet number and the elasticity number. Both the maximum deviation in the z-direction and the shear-induced self-diffusion increase with the elasticity number and the surface Peclet number. Specifically, we find two mechanisms underlying the effects of surfactant on the hydrodynamic interaction of two droplets. First, Marangoni stress induced by surfactant sharply increases the maximum deviation in the z-direction when the surface Peclet number is large. It is because that Marangoni stress hinders liquid drainage from the near-contact region and thickens the liquid film between the droplets. Second, hydrodynamic interactions during crossing lead to considerable alterations of the shape and local surfactant concentration, resulting in an irreversible trajectory shift of the droplets. So, the shear-induced self-diffusion sharply rises at the high surface Peclet number. © 2023, The Authors. All rights reserved.

关键词： Surface active agents

Dynamic Response of Offshore Wind Turbine on 3×3 Barge Array Floating Platform under Extreme Sea Conditions

学校读者我要写书评

暂无评论

China Ocean engineering 2021年第2期35卷 186-200页

作者： LIU Qing-song MIAO Wei-pao YUE Min-nan LI Chun WANG Bo DING Qingwei School of Energy and Power Engineering University of Shanghai for Science and TechnologyShanghai 200093China Shanghai Key Laboratory of Multiphase Flow and Heat Transfer in Power Engineering Shanghai 200093China

Offshore wind farm construction is nowadays state of the art in the wind power generation ***,deep water areas with huge amount of wind energy require innovative floating platforms to arrange and install wind turbines in order to harness wind energy and generate *** conventional floating offshore wind turbine system is typically in the state of force imbalance due to the unique sway characteristics caused by the unfixed foundation and the high center of gravity of the ***,a floating wind farm for 3×3 barge array platforms with shared mooring system is presented here to increase stability for floating *** NREL 5 MW wind turbine and ITI Energy barge reference model is taken as a basis for this ***,the unsteady aerodynamic load solution model of the floating wind turbine is established considering the tip loss,hub loss and dynamic stall correction based on the blade element momentum(BEM)*** second development of AQWA is realized by FORTRAN programming language,and aerodynamic-hydrodynamic-Mooring coupled dynamics model is established to realize the algorithm solution of the ***,the 6 degrees of freedom(DOF)dynamic response of single barge platform and barge array under extreme sea condition considering the coupling effect of wind and wave were observed and investigated in *** research results validate the feasibility of establishing barge array floating wind farm,and provide theoretical basis for further research on new floating wind farm.

关键词： Barge floating platform extreme sea conditions dynamic response stability

Experimental Study on Boiling Heat Transfer Characteristics in Helical Coils with Large Coiled Diameters

学校读者我要写书评

暂无评论

SSRN 2024年

作者： Shi, Yanggen Wu, Zhiyuan Li, Kepiao Zhang, Kui Tian, Wenxi Qiu, Suizheng State Key Laboratory of Multiphase Flow in Power Engineering Department of Nuclear Science and Technology Xi’an Jiaotong University Xi’an710049 China

The boiling heat transfer characteristics in helical coils were investigated by experimental study. Experimental results indicated that the distribution of wall temperature trended to be more uniform due to weakened influence of centrifugal force and gravity force when the bulk fluid is closed to saturation temperature. Increase in heat flux decreases the quality of ONB (onset of nucleate boiling) while increase in mass flux delay ONB. The heat transfer was dominated by nucleate boiling with quality range of 00.6 in saturated boiling region. The quality of dryou decreases with the increase of pressure and it’s scarcely affected by heat flux. Dryout rends to occur at lower quality with the increase of heat flux at high pressure since redeposition rate decreases at higher pressure and entrainment rate increases due to higher heat flux © 2024, The Authors. All rights reserved.

关键词： Heat flux

Numerical Simulation of Fluid-Particle flow of Jet in Supercritical Water Environment

学校读者我要写书评

暂无评论

SSRN 2023年

作者： Zhang, Chuan Shang, Yuqi Su, Haozhe Ge, Zhiwei Guo, Liejin State Key Laboratory of Multiphase Flow in Power Engineering Xi’an Jiaotong University Xi’an710049 China

Supercritical water gasification provides a new approach to the green transformation of coal. Nevertheless, the flow behaviour of the fluid and particles inject into the reactor through the nozzle still warrant further research. In this paper, a three-dimensional numerical simulation of the particle jet in supercritical water environment is carried out using LES-DPM. The simulations focus on the effects of particle size, Stokes number, mass flux ratio and fluid initial velocity on the flow characteristics of the fluid-solid flow. The findings were that as the particle size decreases and the initial fluid velocity increases, the evolution of vortex structures became increasingly fierce, such as the destruction of large-scale coherent structures, the disappearance of vortex ribs, and the lateral expansion of vortices in the development section. Particle distribution exhibited characteristics similar to the vortex structure due to particles stuck closely with the carrier fluid when Stokes number is small (St1), the particles were freer from fluid interference and kept their original motion state moving forward. The fluid velocity at the center of the transverse interface jet decreased with increased mass flow ratio. © 2023, The Authors. All rights reserved.

关键词： Vortex flow

Influence of Wellbore Trajectory on Pressure Drop and Fluid Discharge

学校读者我要写书评

暂无评论

Fluid Dynamics & Materials Processing 2023年第8期19卷 2053-2066页

作者： Ruidong Wu Guowei Wang Zhixing Yang Ruiquan Liao Yang Cheng Shanghai Branch of CNOOC(China)Co. Ltd.Shanghai200335 CNPC Key Laboratory of Oil and Gas Productions on Yangtze University Jingzhou434023China Petrochina Multiphase Flow Laboratory of Gas Lift Innovation Center Wuhan430100China Petroleum Engineering College of Yangtze University Wuhan430100China

An experimental analysis has been conducted to study the process of fluid accumulation for different borehole *** specifically,five heel angles have been experimentally realized to simulate the borehole trajectory of the sloping section of the *** fluid-carrying capacity,pressure drop and fluid discharge volatility have been investigated for these conditions and,accordingly,the relationship between heel angle and wellbore pressure drop fluid-carrying capacity has been *** results show that while the reasonable roll angle can increase the pressure loss in the wellbore,it is beneficial to *** terms of pressure loss and liquid-carrying capacity,when the heeling angle is 50°,the latter is increased while the former becomes very high,which indicates that when drilling and completing wells on site,a 50°roll angle should be *** is found that the main reason for the increase of the total pressure drop in the wellbore is the increase of the local pressure loss in the inclined *** the perspective of drainage stability,when there is heeling in the inclined section of the horizontal well,the fluctuation of the wellbore drainage tends to be *** the comparison of the Beggs-Brill(B-B)and Mukherjee-Brill liquid holdup methods,it is found that B-B method better predicts liquid holdup.A new method for calculating the pressure drop in the inclined section in the presence of lateral inclination is obtained by taking into account the pressure drop in the curved *** comparison with experimental data,it is found that the error is within 20%,and the prediction accuracy is high.

关键词： Horizontal well slant section heel angle pressure drop drainage quantity

Experimental Study on the Plate-Type Fuel Melting Behaviors Based on Alternative Materials

学校读者我要写书评

暂无评论

SSRN 2024年

作者： Wu, Zhiyuan Li, Kepiao Zhang, Kui Chen, Ronghua Tian, Wenxi Qiu, Suizheng State Key Laboratory of Multiphase Flow in Power Engineering Department of Nuclear Science and Technology Xi’an Jiaotong University Xi’an710049 China

In this paper, low-temperature experiments are carried out on the visualized experimental device to study the melting behavior of plate-type fuel in severe accidents of the reactor. In the experiments, the plate-type fuel with different sizes made of nickel-chromium alloy, zinc and aluminum was used to carry out the visualized experiments in air, argon, and vacuum environment. It was found that both the size of the plate and the experimental environment have a significant influence on the melting behavior in this study. And the temperature distribution, melting behavior characteristic, the key parameters such as foaming position, foaming size, breaking position and breaking size were also obtained. Based on the experimental data, the physical phenomena and processes related to the blistering and melting of the fuel plates are analyzed in this paper, which provides experimental data support for the development of analysis model and formulating perfect mitigation strategies for severe accidents. © 2024, The Authors. All rights reserved.

关键词： Melting

Manipulating metal-oxygen local atomic structures in singlejunctional p-Si/WO_(3) photocathodes for efficient solar hydrogen generation

学校读者我要写书评

暂无评论

Nano Research 2021年第7期14卷 2285-2293页

作者： Wu Zhou Chung-Li Dong Yiqing Wang Yu-Cheng Huang Lingyun He Han-Wei Chang Shaohua Shen International Research Center for Renewable Energy State Key Laboratory of Multiphase Flow in Power EngineeringXi’an Jiaotong UniversityShaanxi 710049China Department of Physics Tamkang UniversityTamsui 25137TaiwanChina

Self-passivation in aqueous solution and sluggish surface reaction kinetics significantly limit the photoelectrochemical(PEC)performances of silicon-based ***,a WO_(3) thin layer is deposited on the p-Si substrate by pulsed laser deposition(PLD),acting as a photocathode for PEC hydrogen *** to bare p-Si,the single-junctional p-Si/WO_(3) photoelectrodes exhibit excellent and stable PEC performances with significantly increased cathodic photocurrent density and exceptional anodic shift in onset potential for water *** is revealed that the WO_(3) layer could reduce the charge transfer resistance across the electrode/electrolyte interface by eliminating the effect of Fermi level pinning on the surface of *** importantly,by varying the oxygen pressures during PLD,the collaborative modulation of W–O bond covalency and WO6 octahedral structure symmetry contributes to the promoted charge carrier transport and ***,a large band bending at the p-Si/WO_(3) junction,induced by the optimized O vacancy contents in WO_(3),could provide a photovoltage as high as~500 mV to efficiently drive charge transfer to overcome the water reduction ***,by manipulating W–O local atomic structures in the deposited WO_(3) layer,a great improvement in PEC performance could be achieved over the singlejunctional p-Si/WO_(3) photocathodes for solar hydrogen generation.

关键词： silicon local atomic structure water splitting photocathodes hydrogen generation