检索结果-内蒙古大学图书馆

Experimental Investigation on Heat Transfer Characteristics of Water in Inclined Downward Tube of a Supercritical Pressure CFB Boiler

引用

Journal of Thermal Science 2015年第5期24卷 478-487页

作者： WANG Siyang YANG Dong XIE Beibei WANG Long WANG Yongjie State Key Laboratory of Multiphase Flow in Power Engineering Xi’an Jiaotong University

In this study, experiments have been performed for an investigation on heat transfer of water in an inclined downward tube with an inner diameter of 20 mm and an inclined angle of 45° from the horizon, with the range of pressure from 11.5 to 28 MPa, mass flux from 450 to 1550 kg/(m2 s), and heat flux from 50 to 585 k W/m2. Based on the experimental data, the temperature distribution in the tube wall was derived. The heat transfer characteristics of inclined downward flow were compared with that of vertical downward flow. The effects of heat flux on wall temperature were analyzed and the corresponding empirical correlations were presented. The results show that heat transfer characteristics of water in the inclined downward tube are not uniform along the circumference from the top surface to the bottom surface. An increase in heat flux exacerbates the non-uniformity. At subcritical pressures, both dry-out and departure from nucleate boiling(DNB) occur at the top surface of the inclined downward tube; inversely, only dry-out takes place on the bottom surface of the inclined downward tube and in the vertical downward tube. At near-critical pressures, DNB and dry-out occur in the comparing tubes with greater possibility. At supercritical pressures, heat transfer gets enhanced in the pseudo-critical enthalpy region; in the high enthalpy region, the top surface temperature of the inclined downward tube decreases obviously.

关键词： inclined downward tube wall temperature circumferential non-uniformity heat transfer deterioration

来源：评论

学校读者我要写书评

暂无评论

Industrialization prospects for hydrogen production by coal gasification in supercritical water and novel thermodynamic cycle power generation system with no pollution emission

引用

Science China(Technological Sciences) 2015年第12期58卷 1989-2002页

作者： GUO LieJin JIN Hui GE ZhiWei LU YouJun CAO ChangQing State Key Laboratory of Multiphase Flow in Power Engineering Xi'an Jiaotong University

Energy conversion and utilization, particularly carbon-based fuel burning in air phase, have caused great environmental pollution and serious problems to society. The reactions in water phase may have the potential to realize clean and efficient energy conversion and utilization. Coal gasification in supercritical water is a typical carbon-based fuel conversion process in water phase, and it takes the advantages of the unique chemical and physical properties of supercritical water to convert organic matter in coal to H2 and CO2. N, S, P, Hg and other elements are deposited as inorganic salts to avoid pollution emission. The state key laboratory of multiphase flow in Power engineering has obtained extensive experimental and theoretical results based on coal gasification in supercritical water. Supercritical water fluidized bed reactor was developed for coal gasification and seven kinds of typical feedstock were selected. The hydrogen yield covers from 0.67 to 1.74 Nm3/kg and the carbon gasification efficiency is no less than 97%. This technology has a bright future in industrialization not only in electricity generation but also in hydrogen production and high value-added chemicals. Given the gas yield obtained in laboratory-scale unit, the hydrogen production cost is U.S.$ 0.111 Nm3 when the throughput capacity is 2000 t/d. A novel thermodynamic cycle power generation system based on coal gasification in supercritical water was proposed with the obvious advantages of high coal-electricity conversion efficiency and zero pollutant emission. The cost of U.S.$ 3.69 billion for desulfuration, denitration and dust removal in China in 2013 would have been saved with this technology. Five kinds of heat supply methods are analyzed and the rates of return of investment are roughly estimated. An integrated cooperative innovation center called a new type of high-efficient coal gasification technology and its large-scale utilization was founded to enhance the industrialization o

关键词： industrialization prospects hydrogen production supercritical water gasification power generation zero emission

来源：评论

学校读者我要写书评

暂无评论

Numerical Analysis of flow Instability in the Water Wall of a Supercritical CFB Boiler with Annular Furnace

引用

Journal of Thermal Science 2016年第4期25卷 372-379页

作者： XIE Beibei YANG Dong XIE Haiyan NIE Xin LIU Wanyu State Key Laboratory of Multiphase Flow in Power Engineering Xi'an Jiaotong University

In order to expand the study on flow instability of supercritical circulating fluidized bed(CFB) boiler,a new numerical computational model considering the heat storage of the tube wall metal was presented in this *** lumped parameter method was proposed for wall temperature calculation and the single channel model was adopted for the analysis of flow *** on the time-domain method,a new numerical computational program suitable for the analysis of flow instability in the water wall of supercritical CFB boiler with annular furnace was *** verify the code,calculation results were respectively compared with data of commercial *** to the comparisons,the new code was proved to be reasonable and accurate for practical engineering application in analysis of flow *** on the new program,the flow instability of supercritical CFB boiler with annular furnace was simulated by time-domain *** 1.2 times heat load disturbance was applied on the loop,results showed that the inlet flow rate,outlet flow rate and wall temperature fluctuated with time eventually remained at constant values,suggesting that the hydrodynamic flow was *** results also showed that in the case of considering the heat storage,the flow in the water wall is easier to return to stable state than without considering heat storage.

关键词： supercritical CFB with annular furnace heat storage flow instability wall temperature numerical analysis

来源：评论

学校读者我要写书评

暂无评论

Occurrence and flow Characteristics of Methane in High-Temperature and High-Pressure Nanopores of Deep Shale

引用

Kung Cheng Je Wu Li Hsueh Pao/Journal of engineering Thermophysics 2025年第4期46卷 1200-1204页

作者： Wang, Rui Sun, Chengzhen Yang, Xu State Key Laboratory of Multiphase Flow in Power Engineering Xi’an Jiaotong University Xi’an710049 China Petroleum Engineering School Southwest Petroleum University Chengdu610500 China

The understanding of gas transport in deep shale nanopores is still not clear. In this study, molecular simulations of methane occurrence and flow in illite slits of deep shales under the condition of high-temperature and high-pressure was carried out. The occurrence, diffusion and flow characteristics of methane molecules were analyzed. The effects of temperature and pressure on methane occurrence and flow were elucidated. The results show that the distribution of methane density in illite slits is nonuniform, and there are density peaks near the wall. Compared with Middle and Shallow shales, more methane molecules can exist in the pores of deep shale, and the diffusion ability is limited. The methane flow flux decreases with the decrease of pressure (5∼80 MPa) and increases with the decrease of temperature (60∼120◦C). Pressure is the main dominating factor of flow flux, and the flow flux decreases gradually during depressurization. © 2025 Science Press. All rights reserved.

关键词： Nanopores

来源：评论

学校读者我要写书评

暂无评论

Critical anomaly and finite size scaling of the self-diffusion coefficient for Lennard Jones fluids by non-equilibrium molecular dynamic simulation

引用

Chinese Physics B 2011年第10期20卷 362-367页

作者： Ahmed Asad 吴江涛 State Key Laboratory of Multiphase Flow in Power Engineering Xi'an Jiaotong University

We use non-equilibrium molecular dynamics simulations to calculate the self-diffusion coefficient, D, of a Lennard Jones fluid over a wide density and temperature range. The change in self-diffusion coefficient with temperature decreases by increasing density. For density ρ＊ = ρσ3 = 0.84 we observe a peak at the value of the self-diffusion coefficient and the critical temperature T＊ = kT/ε = 1.25. The value of the self-diffusion coefficient strongly depends on system size. The data of the self-diffusion coefficient are fitted to a simple analytic relation based on hydrodynamic arguments. This correction scales as N-α, where α is an adjustable parameter and N is the number of particles. It is observed that the values of a 〈 1 provide quite a good correction to the simulation data. The system size dependence is very strong for lower densities, but it is not as strong for higher densities. The self-diffusion coefficient calculated with non-equilibrium molecular dynamic simulations at different temperatures and densities is in good agreement with other calculations fronl the literature.

关键词： self-diffusion coefficient non-equilibrium molecular dynamic simulation Lennard Jonesfluid critical dynamics

来源：评论

学校读者我要写书评

暂无评论

A 3D-dimensional interconnected structured poly (m-phenylene isophthalamide) nanofiber separator with Li1.5Al0.5Ge1.5(PO4)3 for high-safety lithium-sulfur batteries

引用

Journal of Power Sources 2025年 645卷

作者： Liu, Jianwei Zhu, Lei Chai, Qinqin Sun, Shiyi Yang, Xiaomeng Sun, Jingyun Zhang, Yating Zhu, Youyu Yan, Wei College of Chemistry and Chemical Engineering Xi'an University of Science and Technology Shaanxi Xi'an710054 China Key Laboratory of Multiphase Flow in Power Engineering Xi'an Jiao tong University Shaanxi Xi'an710049 China Xi'an Hantang Analysis & Test Co. Ltd Shaanxi Xi'an710201 China

Safety concerns have consistently presented substantial obstacles to the widespread adoption of lithium-sulfur (Li-S) batteries. Conventional polyolefin separators, which are characterized by low flash points and insufficient mechanical strength, pose potential safety hazards, including risks of fire and explosion under extreme operating conditions. In this study, we introduce a thermally stable and non-flammable poly-m-phenyleneisophthalamide (PMIA)-based multifunctional separator (L-PMIA separator), which is enhanced with lithium aluminum germanium phosphate (Li1.5Al0.5Ge1.5(PO4)3 or LAGP) fillers. By incorporating g high-ionic-conductivity LAGP and establishing an interconnected framework, this design effectively mitigates the issues of particle agglomeration and uneven commonly ion transport associated with traditional separators. The L-PMIA separator demonstrates remarkable mechanical strength (with a tensile strength of 8.5 MPa and a puncture force of 0.72 N) and thermal stability (showing no dimensional shrinkage even at 200 °C), while also facilitating the formation of continuous ion channels that inhibit lithium dendrite growth. Consequently, Li-S batteries utilizing the 4L-PMIA separator demonstrated a reversible capacity of 4.97 mAh cm−2 after 150 cycles, even under conditions of high sulfur loading (6.75 mg cm−2), limited electrolyte availability (E/S = 7), and elevated temperatures. This approach offers novel insights for the development of future energy storage systems characterized by enhanced safety and performance. © 2025 Elsevier B.V.

关键词： Lithium sulfur batteries

来源：评论

学校读者我要写书评

暂无评论

Calculation of the Critical Speed and Stability Analysis of Cryogenic Turboexpanders with Different Structures

引用

Plasma Science and Technology 2012年第10期14卷 919-926页

作者：陈双涛赵红利马斌侯予 State Key Laboratory of Multiphase Flow in Power Engineering Xi'an Jiaotong University

A modularized code based on the Finite Element QZ （FEQZ） method is developed, for a better estimate of the critical speed and a more convenient method of rotor-dynamic stability analysis for a gas bearing high speed turboexpander rotor system with actual structure and application of a cryogenic turboexpander. This code is then validated by the experimental data of a gas bearing turboexpander, with a rotor diameter of 25 mm and a rated speed of 106,400 rpm. With this code, four rotors with different structures, available to the turboexpander, are parametrically analyzed by the available speed range, vibration modes and logarithmic attenuation rate. The results suggest that the rotor with a structure of two thrust collars on the system exhibits a better performance in the designed conditions.

关键词： critical speed gas bearing cryogenic turboexpander

来源：评论

学校读者我要写书评

暂无评论

Experimental Investigation on Critical Heat Flux for Water flowing in a Vertical Uniformly Heated Rifled Tube under Near-critical Pressures

引用

Journal of Thermal Science 2018年第6期27卷 527-540页

作者： XIE Haiyan YANG Dong ZHAO Yunjie JIANG Huiqing QU Mofeng State Key Laboratory of Multiphase Flow in Power Engineering Xi'an Jiaotong University

This study experimentally investigated the critical heat flux(CHF) of departure from nucleate boiling(DNB) of water flowing under near-critical pressures in a 2 m-long vertical upward rifled tube with the size of Φ35 × 5.67 mm. Operating conditions included pressures of 18–21 MPa, mass fluxes of 475–1000 kg·m^(-2)·s^(-1), inlet subcooling temperatures of 3–5°C, and wall heat fluxes of 40–960 kW·m^(-2). Tube wall temperature distribution and heat transfer performance in different test conditions were obtained. The effects of the operating parameters on CHF were analyzed. Four heat transfer coefficient correlations were evaluated against our experimental data for further investigation of the two-phase heat transfer characteristics. A heat transfer correlation based on Martinelli number utilized in two-phase region and two empirical correlations used to predict the CHF in rifled tube at near-critical pressures were proposed. Meanwhile, experimental CHF data in rifled tube were compared with six widely used correlations and a CHF look-up table. The CHF enhancement effect in rifled tube is obvious as compared with the CHF data in smooth tube. Results show that DNB occurs at low vapor quality and subcooled region in the rifled tube at near-critical pressures. The increase in pressure leads to the early occurrence of DNB and the decrease in CHF, whereas the increase in mass flux delays the occurrence of DNB and results in the increase in CHF. DNB presents a tendency to move toward the inlet of the rifled tube. At individual operating conditions, DNB and dryout coexist at different sections of the rifled tube.

关键词： critical heat flux near-critical pressure rifled tube DNB heat transfer

来源：评论

学校读者我要写书评

暂无评论

Effect of the Density Difference on Fluid Distribution in Layered Rock Samples

引用

Energy & Fuels 2025年第9期39卷 4412-4420页

作者： Yongfei Yang Tonghui Liu Yingwen Li Weichen Sun Hai Sun Lei Zhang Junjie Zhong Kai Zhang Jun Yao State Key Laboratory of Deep Oil and Gas China University of Petroleum (East China) Qingdao 266580 P. R. China；Research Center of Multiphase Flow in Porous Media School of Petroleum Engineering China University of Petroleum (East China) Qingdao 266580 P. R. China Geosteering & Logging Research Institute Sinopec Matrix Corporation Qingdao 266071 P. R. China Research Center of Multiphase Flow in Porous Media School of Petroleum Engineering China University of Petroleum (East China) Qingdao 266580 P. R. China

During geological CO2storage, gravity segregation due to fluid density differences significantly affects the efficiency and safety of the process. This can result in premature CO2breakthrough, reduced storage efficiency, and increased leakage risks. This study aims to investigate how gas migrates in layered heterogeneous reservoirs over time due to prolonged density differences and to assess the resulting impact on fluid distribution. We use artificially layered heterogeneous sandstone cores for experimentation. After completing gas injection and water flooding experiments, the core was positioned with the low permeability layer (LPL) at the top and the high permeability layer (HPL) at the bottom for an extended period. Because the effects of density differences are not easily discernible during gas–water two-phase flow under typical driving forces, we applied micro-CT imaging technology to visualize and analyze how density differences influence gas flow within the core. The results demonstrate that during the static placement period following displacement, gas clusters exhibit different flow behaviors at the pore throats. Most gas clusters struggle to overcome the Jamin effect and enter into the upper pores; a few large-volume gas clusters, driven by density differences, partially pass through the throats into the upper pores, while the remaining portions are stranded within the throats, leading to a snap-off phenomenon; while some gas clusters successfully overcome the Jamin effect and enter the upper pores in significant numbers. The experimental findings indicate that the LPL effectively hinder the upward migration of the nonwetting phase gases from bottom and fluid density differences significantly influence gas–water distribution changes. This study provides critical insights for optimizing CO2storage and offers a new perspective on fluid behavior in layered heterogeneous reservoirs.

关键词：

来源：评论

学校读者我要写书评

暂无评论

Impact of lipophilic particles on oil-water separation efficiency in hydrocyclones

引用

Chemical engineering and Processing - Process Intensification 2025年 214卷

作者： Zhao [赵立新], Lixin Wang [王丽娜], Lina Zhang [张爽], Shuang Guo [郭昭阳], Zhaoyang Lu [卢梦媚], Mengmei School of Mechanical Science and Engineering Northeast Petroleum University Heilongjiang Daqing163318 China Heilongjiang Key Laboratory of Petroleum and Petrochemical Multiphase Treatment and Pollution Prevention Heilongjiang Daqing163318 China State Key Laboratory of Continental Shale Oil Heilongjiang Daqing163318 China

Currently, oilfields have generally entered the high water content extraction period. The ASP (alkali-surfactant-polymer) flooding technology is widely used;however, the presence of polymer in the extracted fluid makes subsequent processing difficult, and it is challenging to achieve efficient oil-water separation using existing hydrocyclone separation technology alone. Therefore, in this study, lipophilic particles were added to the oil-water mixture to be separated, in order to adsorb and transport oil droplets, thereby improving oil-water separation efficiency. An experimental research program was proposed to treat an oil-water mixture using activated carbon as an adsorbent. The effects of parameters such as particle dosage, oil concentration in the mixture, and adsorption time on the adsorption effectiveness of activated carbon were investigated. Comparative analyses were conducted on particle transport trajectories and separation performance between conventional hydrocyclone and lipophilic particle-coupled hydrocyclone. The results show that the addition of lipophilic particles can effectively adsorb and transport oil droplets, significantly improving the oil-water separation efficiency, with the separation efficiency reaching up to 99.97 %. © 2025 Elsevier B.V.

关键词： Petroleum transportation

来源：评论

学校读者我要写书评

暂无评论

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

请选择保存的检索档案：

请选择收藏分类：

通借通还

建议与咨询 留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

请选择保存的检索档案： 新增检索档案 确定 取消

请选择收藏分类： 新增自定义分类 确定 取消

通借通还

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

请选择保存的检索档案：

请选择收藏分类：