Thin films of anatase TiO 2 nanotube arrays (TiO2 NTs) were prepared in this study. Pt and Ag were coated on the TiO2 NTs films, which intend to increase the photocatalytic activity under ultraviolet- visible (UV-vis)...
详细信息
Ignition delay times are obtained for kerosene/air mixtures behind the reflected shock waves at temperatures between 1445 and 1650 K,at a pressure of 0.11 MPa and an equivalence ratio of 1.0.A nebulization device with...
详细信息
Ignition delay times are obtained for kerosene/air mixtures behind the reflected shock waves at temperatures between 1445 and 1650 K,at a pressure of 0.11 MPa and an equivalence ratio of 1.0.A nebulization device with Laval nozzle is used to nebulize kerosene and form an aerosol phase,which evaporates and diffuses rapidly behind the incident shock *** auto-ignite behind the reflected shock *** ICCD is used to visualize the kerosene/air mixture's ignition *** mixture's ignition intensity increases with increase in initial *** and irregular flames exist below 1515 K while plane and discontinuous flames exist over 1560 *** delay times decrease with increase in initial *** data shows good agreement with results reported previously in the literature.A new surrogate (consisting of 10% toluene,10% ethylbenzene and 80% n-decane) is proposed for *** et al.'s mechanism is used to simulate the ignition of kerosene with calculations agreeing well with the experimental *** sensitivity of reaction H+O2 <=>OH+O,which shows the highest sensitivity to the ignition delay time,increases with an increase in *** chain breaching reaction of CH3 with O2 accelerates the total reaction rate and the H-atom abstraction of n-decane controls the total reaction *** rate of production and instantaneous heat production indicate that two reactions,H+O2 <=>OH+O and O+H2 <=>OH+H,are the key reactions to the formation of OH radicals,as well as the main endothermic ***,the reaction of R3 is the main heat release reaction during *** structure analysis shows that initial pressure is increased slightly as CO and H2O will appear before main ignition.
In this work a series of Eosin Y-ZnO(x%)/TiO2 were prepared. ZnO well dispersed on the surface of TiO2, which improves the adsorption of Eosin Y and the excited electron to transfer to the conduction band of TiO2. The...
详细信息
In this paper, a three-layer Back Propagation (BP) algorithm artificial neural network (ANN) for predicting critical heat flux (CHF) in saturated forced convective boiling on a heated surface with impinging jets was t...
详细信息
The Ni-doped (CuIn)0.2Zn1.6S2 photocatalysts were prepared via a two-step ultrasonic-hydrothermal method under an environmental-friendly condition. XRD pattern profiles suggested that Ni2+ successfully doped into (CuI...
详细信息
As the speed of high-speed train (HST) increases continuously, aerodynamic noise has become more important compared with the wheel/rail noise, which affects the inhabited environment around the railway and the comfort...
详细信息
An effective way to boost natural gas production from low pressure gas field was introduced in the paper. The supersonic ejector used the energ off high pressure gas wells, which was generally wasted through the choke...
详细信息
The experiment of flow boiling heat transfer on micro-pin-finned chips in FC-72 with jet impingement was *** experimental conditions consisted of two different liquid subcooling degrees (25,35°C),three different ...
详细信息
The experiment of flow boiling heat transfer on micro-pin-finned chips in FC-72 with jet impingement was *** experimental conditions consisted of two different liquid subcooling degrees (25,35°C),three different cross flow velocities (Vc=0.5,1,1.5 m/s) and three different jet velocities (Vj=0,1,2 m/s).The dimensions of the silicon chips were 10 mm×10 mm×0.5 mm (length×width×thickness) on which two kinds of micro-pin-fins with the dimensions of 30 μm×120 μm,50 μm×120 μm (thickness×height) were fabricated by the dry etching technique. A smooth surface was also tested for comparison. The correlations for nucleate boiling curves and the maximum allowable heat flux curves were obtained. The results show that the heat transfer performance was improved with increasing liquid subcooling and flow velocity. All micro-pin-finned surfaces displayed a considerable heat transfer enhancement. The addition of jet impingement further enhanced the heat transfer at a high heat flux and increased the CHF. At a certain cross flow velocity, the enhancement was more significant as the jet velocity increased, especially for Vc=0.5 m/s, Vj=2 m/s. For the micro-pin-finned chips, the CHF increased by more than 93% while the subcooling was 35°C compared with Vc=0.5 m/s, Vj=0 m/s. As the cross velocity increased, the intensification degree of jet impingement decreased and the increase of CHF also decreased.
暂无评论