检索结果-内蒙古大学图书馆

Numerical Investigation on the Performance of Different Primary Nozzle Structures in the Supersonic Ejector

Energy Procedia 2017年 105卷 4997-5004页

作者： Kangkang Xue Kaihua Li Weixiong Chen Daotong Chong Junjie Yan State Key Laboratory of Multiphase Flow in Power Engineering Xi’an JiaotongUniversity Xi’an Shaanxi 710049 P.R. China

Computational fluid dynamics (CFD) technique is employed to investigate the effect of primary nozzle structures on the supersonic ejector performance. The performance of the supersonic ejectors with three different nozzle structures, including conical nozzle, petalage nozzle and crenation nozzle, have been compared under the same conditions. Compared with the ejector equipped with the conical nozzle, the entrainment ratio of petalage nozzle is slightly smaller, while the critical back pressure increases by 5.2%. Just the opposite, the entrainment ratio of crenation nozzle is slightly higher, and the critical back pressure would decrease by 2.1%. In addition, the effects of primary/induced fluid pressure on the flow field (pressure and Mach number along the ejector centerline) are observed and analyzed to explain the mixing process occurring inside the ejector. It finds out that the shape of the mixing layer in the supersonic ejector with different nozzles is different.

关键词： Supersonic ejector CFD Primary nozzle Entrainment ratio Critical back pressure

来源：评论

学校读者我要写书评

暂无评论

Spontaneous photoelectric field-enhancement effect prompts the low cost hierarchical growth of highly ordered heteronanostructures for solar water splitting

引用

Nano Research 2016年第6期9卷 1561-1569页

作者： Yankuan Wei Jinzhan Su XiaokangWan Liejin Guo Lionel Vayssieres International Research Center for Renewable Energy State Key Laboratory for Multiphase Flow in Power Engineering School of Energy &Power Engineering Xi'an Jiaotong University Xi'an 710049 China

In this study, a potentially universal new strategy is reported for the large-scale, low-cost fabrication of visible-light-active highly ordered heteronanostructures based on the spontaneous photoelectric-field-enhancement effect inherent in pyramidal morphology. The hierarchical vertically oriented arrayed structures comprise an active molecular co-catalyst at the apex of a visible-light-active large band gap semiconductor for low-cost solar water splitting in a neutral aqueous medium without the use of a sacrificial agent.

关键词： bismuth vanadate co-catalysts photocatalysis solar water splitting oxygen evolution

来源：评论

学校读者我要写书评

暂无评论

Thermodynamic Optimization of a Double-pressure Organic Rankine Cycle Driven by Geothermal Heat Source

引用

Energy Procedia 2017年 129卷 591-598页

作者： Qingxuan Sun Yaxiong Wang Ziyang Cheng Jiangfeng Wang Pan Zhao Yiping Dai Institute of Turbomachinery State Key Laboratory of Multiphase Flow in Power Engineering School of Energy and Power Engineering Xi’an Jiaotong University Xi’an 710049 People’s Republic of China

Geothermal energy, as a typical low-temperature heat source, has been exploited for decades to generate electricity. Organic Rankine cycle (ORC) system has a high energy conversion efficiency due to the good performance of organic fluids under the geothermal water temperature. In this study, a double-pressure organic Rankine cycle system driven by geothermal heat source is used to generate electricity. The double-pressure ORC system achieves the cascaded utilization of energy, which can improve the efficiency of energy conversion. Mathematical model is established based on thermodynamic laws, and the overall system performance has been evaluated. A parametric analysis is conducted to examine the effects of some key thermodynamic parameters, namely turbine high-level inlet pressure, turbine low-level inlet pressure, turbine high-level inlet temperature, on the system performance. Parametric optimization is conducted by means of genetic algorithm (GA) to find the maximum system performance. At the same time, the performances of three organic working fluids are examined. Results indicate that R245fa has a better performance among the three organic fluids. The exergy efficiency of overall system exceeds 5.8% under the supply water of 120℃, and it produce more than 800kW electricity with the geothermal water at the mass flow rate of 250t/h. It is also found that the exergy efficiency has peak value under the effect of turbine high-level inlet pressure and turbine low-level inlet pressure. In addition, increasing turbine high-level inlet temperature brings a positive effect to the system performance. Exergy analysis is also conducted and the result shows that the main exergy loss occurs in high-pressure evaporator. By system optimization, the double-pressure organic Rankine cycle has a better performance in utilizing geothermal energy than single-pressure system.

关键词： Geothermal Organic Rankine cycle Double-pressure

来源：评论

学校读者我要写书评

暂无评论

Three-dimensional analysis of condensation nanofluid film on an inclined rotating disk by efficient analytical methods

引用

Arab Journal of Basic and Applied Sciences 2018年第1期25卷 28-37页

作者： Hatami, M. Jing, D. Yousif, Majeed A. Department of Mechanical Engineering Esfarayen University of Technology Esfarayen Iran State Key Laboratory of Multiphase Flow in Power Engineering & International Research Center for Renewable Energy Xi’an Jiaotong University Xi’an China Department of Mathematics Faculty of Science University of Zakho Zakho Iraq

In this study, least square method (LSM) and differential transform method (DTM) applied to solve the three dimensional problem of steady nanofluid deposition on an inclined rotating disk is illustrated. The governing non-linear partial differential equations are reduced to the nonlinear ordinary differential equations system by similarity transform. There is a good agreement between the present analytical and numerical results. Results indicate that increasing nanofluid volume fraction leads to increase in temperature profile and highest temperature obtained for aluminium oxide (Al₂O₃)-water case. © 2018, © 2018 The Author(s). Published by Informa UK Limited, trading as Taylor & Francis Group on behalf of the University of Bahrain.

关键词： condensation film DTM film thickness LSM Nanofluid rotating disk

来源：评论

学校读者我要写书评

暂无评论

Black TiO_(2) for solar hydrogen conversion

引用

Journal of Materiomics 2017年第2期3卷 96-111页

作者： Bin Wang Shaohua Shen Samuel S.Mao School of Science MOE Key Laboratory for Non-equilibrium Synthesis and Modulation of Condensed MatterState Key Laboratory for Mechanical Behavior of MaterialsXi'an Jiaotong UniversityXi'an710049China International Research Centre for Renewable Energy State Key Laboratory of Multiphase Flow in Power EngineeringXi'an Jiaotong UniversityShaanxi710049China Xi'an Jiaotong University Suzhou Academy SuzhouJiangsu215123China Department of Mechanical Engineering University of California at BerkeleyBerkeleyCA94720United States Samuel Mao Institute of New Energy Science Hall1003 Shangbu RoadShenzhen518031China

Titanium dioxide(TiO_(2))has been widely investigated for photocatalytic H_(2) evolution and photoelectrochemical(PEC)water splitting since ***,its wide bandgap(3.0-3.2 eV)limits the optical absorption of TiO_(2) for sufficient utilization of solar *** TiO_(2) has been proposed as an effective strategy to enhance its solar absorption and thus the photocatalytic and PEC activities,and aroused widespread research *** this article,we reviewed the recent progress of black TiO_(2) for photocatalytic H_(2) evolution and PEC water splitting,along with detailed introduction to its unique structural features,optical property,charge carrier transfer property and related theoretical *** summarized in this review article,black TiO_(2) could be a promising candidate for photoelectrocatalytic hydrogen generation via water splitting,and continuous efforts are deserved for improving its solar hydrogen efficiency.

关键词： Black TiO_(2) Photoelectrochemical water splitting Photocatalytic Hydrogen evolution

来源：评论

学校读者我要写书评

暂无评论

Prediction on bubble departure diameter of high pressure boiling water in vertical upward smooth tubes 17

Prediction on bubble departure diameter of high pressure boi...

引用

17th International Topical Meeting on Nuclear Reactor Thermal Hydraulics, NURETH 2017

作者： Guo, Kaikai Li, Huixiong Zhang, Qing Kong, Xiangfei Luo, Qing Xue, Yuqing State Key Laboratory of Multiphase Flow in Power Engineering Xi’an Jiaotong University Xi'an Shaanxi China China Huaneng Clean Energy Research Institute Beijing102209 China Xi’an Thermal Power Research Institute Co. Ltd Xi'an Shaanxi China

As one of the most important parameters of boiling phenomena, the bubble departure diameter has great influence on the vapor-liquid interfacial heat transfer and the convection heat transfer between the wall and the fluid involved. At present, the RPI wall boiling model has been often used to simulate the boiling phenomenon, however, due to the fact that the existing bubble departure diameter models embedded in the RPI wall boiling model were mostly derived from fitting of limited experimental data, there exists great limitation to the applicability of the RPI wall boiling model. Moreover, the experimental data of the bubble departure diameter was mostly obtained at low and middle pressures, and no experimental data of the bubble departure diameter was measured at high pressure (more than 10 MPa). So the effectiveness of the RPI wall boiling model at high pressures should be studied further. A series experimental investigations on the heat transfer of high pressure boiling water in vertical upward tubes has been conducted at the Hi-TaP-XJTU test loop, and wall temperatures of vertical upward tubes were acquired at pressures ranging from 1 to 19 MPa. In combinations with the experimental studies, numerical simulations were performed on the heat transfer of high pressure boiling water flow in vertical upward tubes by using the RPI wall boiling model under conditions corresponding to the experimental investigation. Then,, the reference diameter (dref) used in the Tolubinsky bubble departure diameter model was modified and selected for a specific water pressure so as to make the numerically-obtained wall temperature to satisfactorily match the corresponding experimentally-measured wall temperature at the specific pressure. It was found that the value of dref was closely related to the pressures of the boiling water, but was independent of the mass flux of the water and the heat flux on the wall at a specific pressure. Based on a correlation between the water pressures a

关键词： Heat flux

来源：评论

学校读者我要写书评

暂无评论

Ferrites boosting photocatalytic hydrogen evolution over graphitic carbon nitride: a case study of(Co, Ni)Fe_2O_4 modification

引用

Science Bulletin 2016年第4期61卷 292-301页

作者： Jie Chen Daming Zhao Zhidan Diao Miao Wang Shaohua Shen International Research Center for Renewable Energy State Key Laboratory of Multiphase Flow in Power Engineering Xi’an Jiaotong University

The charge cartier separation and surface catalytic redox reactions are of primary importance as elementary steps in photocatalytic hydrogen evolution. In this study, both of these two processes in photocatalytic hydrogen evolution over graphitic carbon nitride （g-C3N4） were greatly promoted with the earth-abundant ferrites （Co, Ni）Fe2O4 modification. CoFe2O4 was further demonstrated to be a better modifier for g-C3N4 as compared to NiFe2O4, due to the more efficient charge carrier transfer as well as superior surface oxidative catalytic activity. When together loading CoFe2O4 and reductive hydrogen production electrocatalyst Pt onto g-C3N4, the obtained Pt/g-C3N4/CoFe2O4 photocatalyst achieved visible-light （2 〉 420 nm） hydrogen production rate 3.5 times as high as Pt/g-C3N4, with the apparent quantum yield reaching 3.35 % at 420 nm.

关键词： Graphitic carbon nitride FerritesPhotocatalytic water splitting Solar hydrogenconversion

来源：评论

学校读者我要写书评

暂无评论

Correlations of Coal Chemical Properties in China: Quantitative Analysis from Thousands of Data

引用

Energy Procedia 2017年 105卷 1339-1343页

作者： Chang’an Wang Song Wu Wufeng Chen Qiang Lv Defu Che State Key Laboratory of Multiphase Flow in Power Engineering School of Energy and Power Engineering Xi’an Jiaotong University No 28 Xianning West Road Xi’an 710049 China

Coal chemical properties show conspicuous impacts on its reactivity and thermal conversion. Nevertheless, the quantitative analysis of coal property indice in China is insufficient. Here, we quantitatively analyzed the correlations of various chemical properties of coals from thousands of data. Noteworthy variations were captured with some quantified expressions between coal properties obtained.

关键词： coal property quantitative analysis fuel ratio coal rank energy conversion fossil fuel

来源：评论

学校读者我要写书评

暂无评论

Multi-objective optimization of a printed circuit heat exchanger design 17

Multi-objective optimization of a printed circuit heat excha...

引用

17th International Topical Meeting on Nuclear Reactor Thermal Hydraulics, NURETH 2017

作者： Wang, L. Chen, M. Shi, S. Che, D. Sun, X. Department of Nuclear Engineering and Radiological Sciences University of Michigan 2355 Bonisteel Blvd. Ann ArborMI48109-2104 United States State Key Laboratory of Multiphase Flow in Power Engineering Xi’an Jiaotong University Xi’an Shaanxi710049 China

Due to their high effectiveness and compact size, printed circuit heat exchangers (PCHEs) appear promising to be employed as intermediate heat exchangers (IHXs) in High-Temperature Gas-cooled Reactors (HTGRs). In the literature, PCHEs of zigzag mini-channel designs have demonstrated superior performance in heat transfer and pressure drop. In this research, a three-dimensional numerical simulation was performed for a PCHE using computational fluid dynamics (CFD) tool ANSYS FLUENT to study the effects of the zigzag pitch and angle, and channel diameter on its thermal-hydraulic performance. The mass, momentum, and energy equations were solved using a finite volume method by considering steady-state, incompressible laminar flow. The FLUENT numerical model was validated by comparing the simulation results with the experimental data obtained in a high-temperature helium test facility. The comparison showed overall good agreement between the simulations and experiments. In addition, it was challenging to obtain accurate correlations/models for the Nusselt number and friction factor with various geometrical and operational parameters considered. In our study, two artificial neural network (ANN) models were applied by utilizing the CFD results to predict the Nusselt number and friction factor in PCHE zigzag channels with different geometrical configurations and operational parameters. Consequently, the computation time needed for the PCHE design optimization process could be significantly reduced. The comparison between the ANN predictions and CFD results showed that the ANN models could predict the numerical data with good accuracies. Furthermore, to achieve an optimal heat exchanger design, two conflicting evaluation criteria were proposed based on the capital and operational costs. Finally, the Non-dominated Sorting Genetic Algorithms (NSGA-II) and the proposed ANN models were combined and utilized to optimize the geometrical design parameters of the zigzag-channel PCHEs.

关键词： Multiobjective optimization

来源：评论

学校读者我要写书评

暂无评论

Effects of Coal Blending and Operating Conditions on Combustion and NO x Emission Characteristics in a Tangentially-fired Utility Boiler

引用

Energy Procedia 2017年 105卷 4015-4020页

作者： Debo Li Qiang Lv Yongxin Feng Chang’an Wang Xuan Liu Kai Chen Kai Xu Jun Zhong Defu Che Electric Power Research Institute of Guangdong Power Grid Corporation Guangzhou 510080 China State Key Laboratory of Multiphase Flow in Power Engineering School of Energy and Power Engineering Xi’an Jiaotong University Xi’an 710049 China

The influences of operating conditions, such as excess air ratio and SOFA arrangement, on temperature distributions, species distributions, NO x emissions and burnout of a tangentially-fired utility boiler using bituminous and blended coal were investigated by numerical approach in the present study. The simulation results show that the fuel type exhibits certain effect on the temperature distributions and the NO x emissions. Moreover, higher excess air ratio could restrain the CO formation but promote NO x emission. The temperature and the species distributions are highly related to the SOFA arrangement. In addition, SOFA technology is still an effective approach to control the NO x emissions during blended coal combustion, while the disadvantageous effect on char burnout should be considered.

关键词： coal blending combustion NOx emission numerical simulation utility boiler

来源：评论

学校读者我要写书评

暂无评论

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

请选择保存的检索档案：

请选择收藏分类：

通借通还

建议与咨询 留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

请选择保存的检索档案： 新增检索档案 确定 取消

请选择收藏分类： 新增自定义分类 确定 取消

通借通还

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

请选择保存的检索档案：

请选择收藏分类：