检索结果-内蒙古大学图书馆

Mechatronics and robotics Engineering (ICMRE), International Conference on

作者： Yao Huang Haotian Ju Songhao Guo Tianjiao Zheng Jie Zhao Yanhe Zhu State Key Laboratory of Robotics and System Harbin Institute of Technology Harbin China

ISBN: (数字)9798331509293

ISBN: (纸本)9798331509309

For knee rehabilitation patients, it is difficult to maintain balance while walking, and completing a normal gait cycle is challenging. Therefore, we propose a lower limb exosuit tailored for the knee rehabilitation patients to assist in normal walking, and experimentally evaluated the assistance effect of the lower limb exosuit. We mimic the mechanism of the skeletal muscles near the knee joint, by contracting and relaxing the length of the flexible Bowden cable between the thigh and calf, generating assistive torque on the knee joint periodically. We use Inertial Measurement Unit (IMU) to measure lower limb motion parameters, identify gait cycle states, and calculate corresponding plantar pressure and knee joint torque for each phase. We compared surface electromyography (sEMG) signals of three muscle groups (biceps femoris (BF), quadriceps femoris (QF), and gastrocnemius (G)) under conditions of wearing and not wearing the exosuit. The experimental results show that compared to not wearing the exosuit, the mean normalized sEMG signals of the three muscle groups decreased by 4.61 %, 2.41 %, and 3.97% respectively while wearing it, the peak values decreased by 11.60%, 25.69%, and 14.99% respectively, with the quadriceps femoris receiving the highest degree of assistance.

关键词： Knee Legged locomotion Limbs Torque Measurement units Thigh Muscles Pressure measurement Torque measurement Robots

来源：评论

学校读者我要写书评

暂无评论

Optimization method for operation configuration of space manipulator for on-orbit assembly 24

Optimization method for operation configuration of space man...

引用

4th International Conference on Control and Intelligent robotics, ICCIR 2024

作者： Li, Mengfei Liu, Yang Feng, Weichao Cao, Baoshi Xie, Zongwu Xie, Yuteng Li, Chongyang Guo, Chuangqiang State Key Laboratory of Robotics and System Harbin Institute of Technology Harbin150001 China School of Resources and Environment Northeast Agricultural University Harbin150006 China Agile Robots Beijing Beijing100192 China

ISBN: (纸本)9798400709937

Aiming at the insertion requirements of large space structures during the on-orbit assembly process, a redundant manipulator operation configuration selection method using joint angle variation as a performance evaluation index is proposed, which achieves operation configuration optimization among multiple sets of inverse solutions. At the same time, the risk of collision during installation is reduced. Firstly, the joint angle parameterization method is used to solve all feasible solutions of the redundant manipulator. Then, trapezoidal velocity planning is employed to analyse the operation configuration after the end effector of the manipulator moves a certain distance in different directions of the coordinate system, and the joint weight coefficient is introduced to calculate the weighted value of the angle variation. Finally, select the operation configuration corresponding to the minimum weighted value as the initial configuration for the manipulator. The calculation results show that this method can select an effective solution that satisfies the posture constraints from multiple sets of inverse solutions, giving full play to the redundant characteristics of the SSRMS-type manipulator and ensuring the safety and reliability of the on-orbit assembly process. © 2024 Copyright held by the owner/author(s).

关键词： Inverse kinematics

来源：评论

学校读者我要写书评

暂无评论

Tool geometry design and microstructure fabrication by micro flat-end milling on soft-brittle LiF surface

引用

Journal of Manufacturing Processes 2025年 149卷 868-877页

作者： Lei, Hongqin Zhang, Zixiao Chen, Liang Guo, Yanqiu Cheng, Jian Zhao, Linjie Chen, Mingjun Yang, Dinghuai Chen, Guang State Key Laboratory of Robotics and System Harbin Institute of Technology Harbin 150001 China School of Mechatronics Engineering Harbin Institute of Technology Harbin 150001 China

The LiF crystal with the three-layer step microstructure is vital in the laser-driven quasi-isentropic compression experiment. However, due to the high chemical activity and easy deliquescence of soft-brittle LiF crystals, brittle fracture can easily occur during the microstructure preparation achieved by the micro-milling technology. Therefore, it is essential to determine the optimal tool geometry and preferred processing parameters to achieve an ultra-smooth surface. A finite element (FE) model of the tool geometry optimization for LiF crystals is constructed based on dimensional analysis and the stress-strain curve obtained by nanoindentation tests. Micro-slot and microstructure preparation experiments are conducted to verify the cutting performance of the manufactured cutters with optimal geometry. It is found that the optimal negative rake/relief angles of side- and bottom edges are determined to be −35°/9° and − 25°/20° for tool I from the perspectives of the tensile stress, cutting force, and tool surface stress (σ1), respectively. For tool II, optimal negative rake/relief angles of the side- and bottom edges are −60°/15° and − 55°/20°, respectively. The σ1 of tool II is 110.3 MPa, which is 0.74 times and 0.95 times that of tool I (149 MPa) and the CBN tool (116.1 MPa), respectively, indicating that tool II has the most substantial wear resistance under the same processing parameters. Besides, compared with other tool structures, the cutting force and tensile stress are the smallest when using the tool II. The small stress can make the milling process stable, and the vibration and impact generated by the tool are smaller, which helps to make the micro-milled surface smooth. Therefore, the average surface roughness processed by tool II is 0.70 times and 0.47 times that of the CBN tool and tool I, respectively, further illustrating the best cutting performance of tool II. Furthermore, for tool II, the optimal spindle speed and feed per tooth are 40,000 r/min a

关键词： Cutting performance Flat-end milling LiF crystals Microstructure fabrication Tool geometry

来源：评论

学校读者我要写书评

暂无评论

A Lower Limb Exosuit for Assisting Knee Joint in Rehabilitation During Walking 11

A Lower Limb Exosuit for Assisting Knee Joint in Rehabilitat...

引用

11th International Conference on Mechatronics and robotics Engineering, ICMRE 2025

作者： Huang, Yao Ju, Haotian Guo, Songhao Zheng, Tianjiao Zhao, Jie Zhu, Yanhe Harbin Institute of Technology State Key Laboratory of Robotics and System Harbin China

ISBN: (纸本)9798331509293

关键词： Neuromuscular rehabilitation

来源：评论

学校读者我要写书评

暂无评论

Recent Advances in Twisted and Coiled Artificial Muscles and Their Applications

SmartBot

引用

SmartBot 2025年第1期1卷 121-140页

作者： Jin Sun Shijing Zhang Jie Deng Jing Li Dehong Wang Junkao Liu Yingxiang Liu State Key Laboratory of Robotics and Systems Harbin Institute of TechnologyHarbinChina

Twisted and coiled artificial muscles(TAMs)have been extensively studied in the field of soft robots due to their exceptional properties,including high energy density,large load-to-weight ratio,large deformation,low driving voltage,and low *** advancements of TAMs hold the potential for enhancing the performance and broadening their functional capabilities of soft robots,thus demonstrating substantial practical *** review outlines the recent progress in TAMs and their diverse applications in soft ***,the commonly used materials to fabricate TAMs,including inorganic fibers,composite fibers,organic fibers,and natural fibers,are discussed along with their ***,the actuation strategies are summarized across four aspects:thermal method,solvent method,electrochemical method and other non-contact ***,the configurations of TAMs are classified into single,parallel and braided *** addition,various soft robots driven by TAMs are introduced according to their functions,including manipulation,locomotion,smart textile,and ***,the research hotspots and development trends of TAMs are *** is expected that this review article can serve as a valuable reference and source of inspiration for researchers in the field of soft actuators and robots.

关键词： actuation strategies artificial muscles soft actuator soft robots

来源：评论

学校读者我要写书评

暂无评论

Design of A Rigid-soft Hybrid Robotic Glove with Force Sensing Function

Design of A Rigid-soft Hybrid Robotic Glove with Force Sensi...

引用

IEEE International Conference on robotics and Automation (ICRA)

作者： Hexin Li Li Jiang Ruichen Zhen Ming Cheng Kehan Ding State Key Laboratory of Robotics and System Harbin Institute of Technology

ISBN: (数字)9798350384574

ISBN: (纸本)9798350384581

Soft robotic gloves can not only provide timely, effective, safe and cheap rehabilitation training for patients with impaired movement function of hand, but also assist in completing daily grasping activities. However, most soft robotic gloves are completely composed of flexible structures. Although they have high flexibility and safety, there are problems such as poor fit and low output force. In order to solve these problems, this paper refers to the structure of the human hand and designs an articulated rigid-soft hybrid robotic glove, which combines the advantages of rigid robotic gloves and soft robotic gloves, and has high flexibility, high output force and good fit. In addition, soft robotic gloves generally lack the ability to sense the force between the human hand and the glove. Therefore, this paper designed an array flexible force sensor, and studied the structure, signal acquisition and preparation process of the sensor. Finally, a complete test platform was built to test the performance of the rigid-soft hybrid robotic glove with force sensing function. The test results show that the robotic glove has good fit and high output force, can effectively assist training and assist grasping, and can perceive the contact force.

关键词： Training Sensitivity Force Grasping Soft robotics Robot sensing systems Safety

来源：评论

学校读者我要写书评

暂无评论

A deep learning-based model for automated STN localization using local field potentials in Parkinson’s disease

引用

Soft Computing 2025年第4期29卷 2343-2362页

作者： Hosny, Mohamed Naeem, Mohamed A. Zhu, Minwei Gao, Wenpeng Elshenhab, Ahmed M. Fu, Yili Department of Electrical Engineering Benha Faculty of Engineering Benha University Benha Egypt State Key Laboratory of Robotics and Systems Harbin Institute of Technology Harbin150080 China Department of Mechatronics and Robotics Engineering Faculty of Engineering South Valley University Qena Egypt First Affiliated Hospital Harbin Medical University Harbin150001 China School of Life Science and Technology Harbin Institute of Technology Harbin150080 China Department of Mathematics Faculty of Science Mansoura University Mansoura35516 Egypt

Accurate identification of the subthalamic nucleus (STN) borders is time-consuming, relying heavily on the neurosurgeon expertise in manually interpreting the electrophysiological signals. Local field potentials (LFPs) have garnered imperative attention due to their strong correlation with the STN. However, existing detection models often face challenges with high computational complexity, hyperparameter optimization and lack of explainability, making them unreliable for clinicians. Therefore, this study introduces an explanatory framework using convolutional neural networks (CNN) for detecting the STN region from LFPs. Continuous wavelet transform is employed to convert LFPs signals into scalogram images, which are then processed by sixteen CNN models. We evaluated our framework by examining the impact of various limiting factors on the classification performance, including model size, learning rate (LR), optimizers and data scaling. Deep features are extracted from the top-performing CNN architectures to capture rich representations of the scalograms. These features are then fused and classified using k-nearest neighbour algorithm. Gradient-weighted class activation mapping is used to explain the decisions made by the proposed model. Our approach achieved an accuracy of 99.61%, outperforming individual CNN models for STN localization. The experimental results revealed that CNN models, embedded with additional hyperparameters and layers, generally outperformed smaller models. Besides, low LR significantly enhanced the performance compared to high LR. Moreover, features extracted from untuned networks produced lower performance than tuned networks. The proposed system could revolutionize deep brain stimulation surgery by increasing efficiency and reducing reliance on clinician expertise for STN detection. © The Author(s), under exclusive licence to Springer-Verlag GmbH Germany, part of Springer Nature 2025.

关键词： Wavelet transforms

来源：评论

学校读者我要写书评

暂无评论

An Efficient and Robust Tightly Coupled Framework for Lidar-IMU Localization and Mapping

An Efficient and Robust Tightly Coupled Framework for Lidar-...

引用

2023 IEEE International Conference on robotics and Biomimetics, ROBIO 2023

作者： Zhai, Yanwu Fu, Yili Li, Xu Zhejiang Laboratory Intelligent Robot Research Center Hangzhou311100 China Harbin Institute of Technology State Key Laboratory of Robotics and System Heilongjiang Province Harbin150001 China

ISBN: (纸本)9798350325706

In this article, we propose a framework for tightly-coupled lidar inertial odometry, which can achieve highly accuracy in real-time ego-motion estimation and map building of the robot. The estimated motion from inertial measurement unit (IMU) preintegration de-skews point clouds. Then, an initialization method based on MAP estimation is used to align the Lidar frame with the world frame and provide reliable initial values for the system. In order to make the scan matching more accurate, we track the state of each frame, and transform the feature points to the reference frame to build a local map for matching with key frames. To ensure high performance in real-time, an efficient sliding window was used to optimize the keyframes we chose. After obtaining the optimized pose of the keyframe, we further optimize the pose of the normal frame by pose constraints. In addition, loop detection is integrated into our algorithm framework to eliminate accumulated errors, making our algorithm to obtain a globally consistent estimate. The experiment results demonstrate that our method can achieve high accuracy in a variety of indoor and outdoor environments even under fast motion conditions or with insufficient features. © 2023 IEEE.

关键词：

来源：评论

学校读者我要写书评

暂无评论

6D Grasp Pose Detection in Cluttered Environment from a Single-view

6D Grasp Pose Detection in Cluttered Environment from a Sing...

引用

2023 IEEE International Conference on robotics and Biomimetics, ROBIO 2023

作者： Li, Enbo Fu, Yili Feng, Haibo Intelligent Robot Research Center Zhejiang Laboratory Hangzhou311100 China Harbin Institute of Technology State Key Laboratory of Robotics and System Heilongjiang Province Harbin150001 China

ISBN: (纸本)9798350325706

Robot grasping has always been a hot topic in the research field, but there are still a lot of problems to be solved. In this paper, we propose a general grasping method for the unknown objects in cluttered environment from a single-view. Our method is divided into three steps: sampling points selection, grasping pose sampling and grasping pose evaluation. Firstly, we generate a pixel-wise probability image based on the trained sampling affordance network from RGB images, and map the points with high probability to the 3D point cloud combined with the depth map. Then, we obtaine the candidate grasps by sampling on the proposal points, and finally we evaluate the candidate grasps through the trained grasp evaluation network. The network can capture the geometric structure represented by the point cloud information. The proposed method directly uses the original sensor data and can increases the sampling success rate. © 2023 IEEE.

关键词：

来源：评论

学校读者我要写书评

暂无评论

Precise semi-analytical inverse kinematic solution for 7-DOF offset manipulator with arm angle optimization

引用

Frontiers of Mechanical Engineering 2021年第3期16卷 435-450页

作者： Boyu MA Zongwu XIE Zainan JIANG Hong LIU School of Mechatronics Engineering Harbin Institute of TechnologyHarbin 150001China State Key Laboratory of Robotics and System Harbin Institute of TechnologyHarbin 150001China

Seven-degree-of-freedom redundant manipulators with link offset have many advantages,including obvious geometric significance and suitability for configuration *** configuration is similar to that of the experimental module manipulator(EMM)in the Chinese Space Station Remote Manipulator ***,finding the analytical solution of an EMM on the basis of arm angle parameterization is *** study proposes a high-precision,semi-analytical inverse method for ***,the analytical inverse kinematic solution is established based on joint angle ***,the analytical inverse kinematic solution for a non-offset spherical-roll-spherical(SRS)redundant manipulator is derived based on arm angle *** approximate solution of the EMM is calculated in accordance with the relationship between the joint angles of the EMM and the SRS ***,the error is corrected using a numerical method through the analytical inverse solution based on joint angle *** selecting the stride and termination condition,the precise inverse solution is computed for the EMM based on arm angle ***,case solutions confirm that this method has high precision,and the arm angle parameterization method is superior to the joint angle parameterization method in terms of parameter selection.

关键词： 7-DOF redundant manipulator inverse kinematics semi-analytical arm angle link offset

来源：评论

学校读者我要写书评

暂无评论

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

请选择保存的检索档案：

请选择收藏分类：

通借通还

建议与咨询 留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

请选择保存的检索档案： 新增检索档案 确定 取消

请选择收藏分类： 新增自定义分类 确定 取消

通借通还

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

请选择保存的检索档案：

请选择收藏分类：