检索结果-内蒙古大学图书馆

computer Vision and Machine Intelligence (CVMI), International Conference on

作者： Seizan Tsugawa Takao Toma Shiho Oshiro Tomohisa Wada Computer Science and Intelligent Systems Program University of the Ryukyus Okinawa Japan Magna Design Net Inc Okinawa Japan Information Technology Center University of the Ryukyus Okinawa Japan Dept. of Engineering Area of Computer Science and Intelligent Systems University of the Ryukyus Okinawa Japan

This paper proposed Scalability in Autoencoder-based Orthogonal Frequency Division Multiplexing(OFDM) communication system. In the previous research, only the comparison between IEEE802.11a and Autoencoder by the conventional OFDM communication system was performed, and it was proved that the communication system created by Autoencoder exceeded the performance of the conventional system. Therefore, in this paper, it uses IEEE802.11n and compare whether it can be improved by expanding the bandwidth and using ***802.11n standard has an FFT length of 128, a subcarrier number of 114 (108 for data), and modulation schemes of Quadrature Phase Shift Keying(QPSK), 16 Quadrature Amplitude Modulation (16QAM). The GI length is 800ns and the symbol length is 4000ns. In the simulation, a computer simulation was performed using a conventional OFDM communication system and a communication system generated by Autoencoder. Assuming that the simulation environment had an Signal-to-Noise Ratio (SNR) of 0 to 30 and an amplitude r of 0.0 to 1.0, the Symbol Error Rate (SER) status for each SNR was output. As a result of computer simulation, QPSK converged at SNR 27 ㏈ at IEEE 802.11a, but was able to reduce SER overwhelmingly to SNR 12 ㏈ at IEEE 802.11n. Also, in 16QAM the convergence at r=0.0 is the same as for SNR22 ㏈, but in IEEE 802.11a it does not converge after r=0.6, but in IEEE 802.11n it does not converge only at r=0.9 and r=1.0 . As a future task, it will use IEEE802.11ac, which enables communication speeds several times faster than IEEE802.11n, examine whether it is possible to further improve accuracy. And it will continue our research to correspond MIMO communication.

关键词：

来源：评论

学校读者我要写书评

暂无评论

Intelligent Constellation Generation based on Autoencoder Communication System

Intelligent Constellation Generation based on Autoencoder Co...

引用

computer Vision and Machine Intelligence (CVMI), International Conference on

作者： Kaisei Matsumoto Takao Toma Shiho Oshiro Tomohisa Wada Computer Science and Intelligent Systems Program University of the Ryukyus Okinawa Japan Magna Design Net Inc Okinawa Japan Information Technology Center University of the Ryukyus Okinawa Japan Dept. of Engineering Area of Computer Science and Intelligent Systems University of the Ryukyus Okinawa Japan

This paper discusses intelligent constellation generation based on autoencoder communication system. In previous studies, the amplitude was set to fluctuate between r=0.0 and 1.0. However, when checking the generated constellation, distortion was confirmed instead of the conventional symbol arrangement. Therefore, in this paper, it compares the case where the amplitude is constant, the case where the average amplitude within a Minibatch is 1, and the case where the average amplitude is 1 for Interval time. The communication standard used in this research is IEEE 802.11a, assuming wireless Local Area Network (LAN) specifications. The IEEE 802.11a standard has an Fast Fourier Transform (FFT) length of 64, a subcarrier number of 52, and Quadrature Phase Shift Keying (QPSK) and 16 Quadrature Amplitude Modulation (QAM), modulation methods. A guard interval of 800 ns is added and the symbol length is 4000 ns. First, a simulation was performed under the condition that the amplitude was kept constant. QPSK with 4 symbols, constant amplitude model is rounded more than previous research result. 16QAM with 16 symbols is arranged regularly like lined up on a line. Second, the simulation was performed under the condition that the average amplitude within the minibatch was set to 1. QPSK with 4 symbols, appears to rotate clockwise. 16QAM with 16 symbols has a more uniform symbol placement than previous research result. Third, a simulation was performed under the condition that the average amplitude within Interval time was set to 1. QPSK with 4 symbols, is the closest to square among QPSK output results so far. The direction is slightly tilted, but if it can be rotated a little more, it may be possible to reproduce the same symbol arrangement as before. 16QAM with 16 symbols, the symbol arrangement is biased as a whole. However, it can be seen that are arranged in line on the line, perhaps due to regularity. As future work, in addition to the conditions set this time, it will exa

关键词：

来源：评论

学校读者我要写书评

暂无评论

Comparative Analysis between Three-Leg Interleaved and Conventional Bidirectional Converters Applied in Battery of Wind Power-Battery Unit Supplying an Islanded Microgrid

Comparative Analysis between Three-Leg Interleaved and Conve...

引用

IEEE General Meeting Power& Energy Society

作者： André C. Do Nascimento Giusep M. S. Ribeiro Lindemberg R. de Lima Pedro A. de Alcântara Luana C. S. Soares Luciano S. Barros Camila M. V. Barros Electrical Engineering Graduate Program Federal Institute of Pará Belém Brazil Electrical Engineering Graduate Program Federal University of Paraíba João Pessoa Brazil Mathematics and Computational Modeling Graduate Program Federal University of Paraíba João Pessoa Brazil Computer Systems Department Federal University of Paraíba João Pessoa Brazil

ISBN: (数字)9798350381832

ISBN: (纸本)9798350381849

Battery energy storage systems (BESS) are crucial for microgrids, enhancing dynamic performance and mitigating uncertainties inherent to isolated environments characterized by intermittent power generation. When microgrid is supplied by wind power in connection with BESS, the bidirectional DC-DC converter associated with BESS assumes a critical responsibility—ensuring the control of a wind power supplied DC-link. This permits the Voltage Source Inverter (VSI) to synthesize consistent voltages for the connected AC load. However, challenges emerge, particularly in arduous stress on switches of the bidirectional converter attributed to elevated current ripple. This stress does not only prejudice the overall system’s functioning but can also potentially leading it to shutdown in case of switch failure. Traditionally, the conventional buck-boost converter topology has been the go-to choice for this application, nevertheless, exploring novel converter topologies, such as interleaved bidirectional DC-DC converter (IBDC) has garnered attention, promising enhanced performance. This paper’s goal is to conduct a comparative analysis of the operation of these converters in an islanded microgrid supplied by a single Permanent Magnet Synchronous Generators (PMSG) small-scale wind turbine with a BESS system. Load variation with Maximum Power Point Tracking (MPPT) operation of the PMSG is performed during MATLAB/Simulink environment simulations. The results suggest significant advantages for the interleaved three-phase converter, such as reduced battery charging current ripple, switch disturbance, and voltage ripple in the DC-link.

关键词： Maximum power point trackers Magnetic separation Microgrids DC-DC power converters Wind power generation Permanent magnets Batteries Topology Wind turbines Stress

来源：评论

学校读者我要写书评

暂无评论

Orchard: building large cancer phylogenies using stochastic combinatorial search

arXiv

引用

arXiv 2023年

作者： Kulman, Ethan Kuang, Rui Morris, Quaid Computational and Systems Biology Program Sloan Kettering Institute New YorkNY United States Department of Computer Science and Engineering University of Minnesota MinneapolisMN United States

Phylogenies depicting the evolutionary history of genetically heterogeneous subpopulations of cells from the same cancer, i.e., cancer phylogenies, offer valuable insights about cancer development and guide treatment strategies. Many methods exist that reconstruct cancer phylogenies using point mutations detected with bulk DNA sequencing. However, these methods become inaccurate when reconstructing phylogenies with more than 30 mutations, or, in some cases, fail to recover a phylogeny altogether. Here, we introduce Orchard, a cancer phylogeny reconstruction algorithm that is fast and accurate using up to 1000 mutations. Orchard samples without replacement from a factorized approximation of the posterior distribution over phylogenies, a novel result derived in this paper. Each factor in this approximate posterior corresponds to a conditional distribution for adding a new mutation to a partially built phylogeny. Orchard optimizes each factor sequentially, generating a sequence of incrementally larger phylogenies that ultimately culminate in a complete tree containing all mutations. Our evaluations demonstrate that Orchard outperforms state-of-the-art cancer phylogeny reconstruction methods in reconstructing more plausible phylogenies across 90 simulated cancers and 14 B-progenitor acute lymphoblastic leukemias (B-ALLs). Remarkably, Orchard accurately reconstructs cancer phylogenies using up to 1,000 mutations. Additionally, we demonstrate that the large and accurate phylogenies reconstructed by Orchard are useful for identifying patterns of somatic mutations and genetic variations among distinct cancer cell subpopulations. © 2023, CC BY.

关键词： Plant diseases

来源：评论

学校读者我要写书评

暂无评论

Implementation and Evaluation of 0.6 µm CMOS Complex RCPF for Accurate Frequency Response Measurement

IEEJ Transactions on Electronics, Information and Systems

引用

IEEJ Transactions on Electronics, Information and systems 2025年第1期145卷 25-37页

作者： Sato, Lina Fukagawa, Kanta Shouno, Kazuhiro Tanimoto, Hiroshi Muto, Cosy Moriyama, Seijiro Takahashi, Chikau Yoshino, Michitaka Graduate School of Science and Technology Degree Programs in Systems and Information Engineering Master’s Program in Computer Science University of Tsukuba Japan Division of Information Engineering University of Tsukuba 1-1-1 Tennoudai Ibaraki Tsukuba305-8573 Japan Kitami Institute of Technology 165 Koen-cho Hokkaido Kitami090-8507 Japan Faculty of Education Nagasaki University 1-14 Bunkyo-machi Nagasaki852-8521 Japan Anagix Corporation 3-22-27 Numama Kanagawa Zushi249-0004 Japan Takamori Corporation Japan Research Center for Micro-Nano Technology Hosei University 3-11-15 Midori-cho Koganei Tokyo184-0003 Japan

This paper describes the implementation and evaluation of an RC polyphase filter (RCPF) and circuitry for measuring its frequency characteristics. The integrated circuit is fabricated on a 0.6 µm CMOS process and its supply voltage is 5 V. The integrated circuit includes a filter under test (FUT), a four-phase square wave generator, several analog switches and differential amplifiers to amplify the high-impedance signals of the RCPF. This FUT is a third-order complex RCPF whose passband is 8 − 40 MHz. This paper describes the design of these circuits in detail. This integrated circuit can select two measurement methods by means of external control signals. The first method uses a four-phase square wave. The frequency characteristics are measured by using an on-chip four-phase square wave generator driven by an external clock generator and by a spectrum analyzer tuned to the fundamental frequency. The second method uses an external network analyzer. Furthermore, this integrated circuit is equipped with a calibration circuit to measure the frequency characteristics of the circuitry except FUT by passing through the input / output signals of the FUT. As a result, the frequency characteristics of the FUT itself can be accurately measured. The effectiveness is confirmed through evaluation of the fabricated integrated circuit. © 2025 The Institute of Electrical Engineers of Japan.

关键词： Differential amplifiers

来源：评论

学校读者我要写书评

暂无评论

Dividing and Conquering a BlackBox to a Mixture of Interpretable Models: Route, Interpret, Repeat

arXiv

引用

arXiv 2023年

作者： Ghosh, Shantanu Yu, Ke Arabshahi, Forough Batmanghelich, Kayhan Department of Electrical and Computer Engineering Boston University MA United States Intelligent Systems Program University of Pittsburgh PA United States MetaAI MenloParkCA United States

ML model design either starts with an interpretable model or a Blackbox and explains it post hoc. Blackbox models are flexible but difficult to explain, while interpretable models are inherently explainable. Yet, interpretable models require extensive ML knowledge and tend to be less flexible and underperforming than their Blackbox variants. This paper aims to blur the distinction between a post hoc explanation of a Blackbox and constructing interpretable models. Beginning with a Blackbox, we iteratively carve out a mixture of interpretable experts (MoIE) and a residual network. Each interpretable model specializes in a subset of samples and explains them using First Order Logic (FOL), providing basic reasoning on concepts from the Blackbox. We route the remaining samples through a flexible residual. We repeat the method on the residual network until all the interpretable models explain the desired proportion of data. Our extensive experiments show that our route, interpret, and repeat approach (1) identifies a diverse set of instance-specific concepts with high concept completeness via MoIE without compromising in performance, (2) identifies the relatively "harder" samples to explain via residuals, (3) outperforms the interpretable by-design models by significant margins during test-time interventions, and (4) fixes the shortcut learned by the original Blackbox. The code for MoIE is publicly available at: https://***/batmanlab/ ICML-2023-Route-interpret-repeat. © 2023, CC BY.

关键词： Iterative methods

来源：评论

学校读者我要写书评

暂无评论

Exploring Personal Knowledge Ecologies: Dealing with Digital Platform Asymmetries

Exploring Personal Knowledge Ecologies: Dealing with Digital...

引用

International Conference on computer Supported Cooperative Work in Design

作者： Marcos Antonio De Almeida Jano Moreira De Souza António Correia Daniel Schneider Systems Engineering and Computer Science Program (PESC/COPPE/UFRJ) Rio de Janeiro Brazil Faculty of Information Technology University of Jyväskylä Jyväskylä Finland Postgraduate Program in Informatics PPGI/UFRJ Rio de Janeiro Brazil Tércio Pacitti Institute of Computer Applications and Research NCE/UFRJ Rio de Janeiro Brazil

ISBN: (数字)9798350349184

ISBN: (纸本)9798350349191

The rise of artificial intelligence agents and information technology platforms governed by data-driven algorithms has had profound impacts on the way knowledge work is managed and carried out. Concerning the novel uses of digital work platforms, the arising tensions might suggest that the socio-technical design frameworks adopted by major tech firms are becoming less viable and in some cases ineffective. We propose a conceptual architecture to support a socio-technical framework for exploring Personal Knowledge Ecologies in the context of the digital knowledge economy. This framework aims to increase the degree of individual freedom for the interoperation of these knowledge information infrastructures.

关键词： Knowledge engineering Sociotechnical systems computer architecture Ecology Software Heterogeneous networks Complexity theory

来源：评论

学校读者我要写书评

暂无评论

Control Design for 3-Phase Bidirectional Battery Chargers with Multiple Battery Charging Capabilities for Electric Vehicle Fleet Applications

Control Design for 3-Phase Bidirectional Battery Chargers wi...

引用

2021 North American Power Symposium, NAPS 2021

作者： Okon, Queen Urquizo, Javier Kondrath, Nisha Singh, Pritpal College of Engineering Sustainable Engineering Program Villanova University Department of Electrical and Computer Engineering VillanovaPA United States L3Harris Technologies Maritime Power Systems PhiladelphiaPA United States

ISBN: (纸本)9781665420815

This paper describes a control structure for a bidirectional battery charger model design which consists of three-phase PWM ac/DC converters linked to a DC/DC converter with a CLLC-type resonant tank circuit. It presents a control structure that accommodates: constant current, constant voltage (CCCV) charging algorithm of an Energy Storage System (ESS), a multiple battery charger setup, and the automation of the combined control system based upon certain conditions being satisfied. The proposed control scheme was simulated and validated for a system integrating two battery charger modules using the PLECS software tool while charging a Li-ion battery model. The interactions between the two modules during the charging process were investigated with and without the introduction of a DC bus. © 2021 IEEE.

关键词： Charging (batteries)

来源：评论

学校读者我要写书评

暂无评论

Analysis of DFIG differential protection based on Park transform

Analysis of DFIG differential protection based on Park trans...

引用

2021 IEEE PES Innovative Smart Grid Technologies Conference - Latin America, ISGT Latin America 2021

作者： De Queiroz, Janailson Maciel Barros, Luciano Sales Barbosa, Daniel Graduate Program on Electrical and Computer Engineering Federal Un. of Rio Grande Do Norte Natal Brazil Federal Un. of Paraíba João Department of Computer Systems Pessoa Brazil

ISBN: (纸本)9781665444217

In recent years, the use of wind energy in the world has grown. Consequently, the need for studies related to the impact of wind turbines on the electrical system has increased including protection of them and associated equipment. For DFIG-based wind turbines, differential protection has recently been proposed, however, there are few studies on this type of application and in this paper it proposes criteria in the decision-making using the Park transform in which, in addition to the restriction current, voltage level and current direction at the stator terminals are considered. In a DFIG operating with 1.51 MW tests of faults internal and external to the protection zone were made, of the single-phase and three-phase type with various levels of voltage drops. Interturn faults in the rotor and stator of the machine were also tested with various levels of defects. So, with the proper definition of the operating logic, it was possible to show the effectiveness of the protection. © 2021 IEEE.

关键词： Wind power

来源：评论

学校读者我要写书评

暂无评论

Application of factor analysis method to support the users acceptance model of ERP systems implementation 4

Application of factor analysis method to support the users a...

引用

4th International Conference on Combinatorics, Graph Theory, and Network Topology, ICCGANT 2020

作者： Sardjono, W. Sudirwan, J. Priatna, W. Putra, G.R. Information Systems Management Department BINUS Graduate Program Master of Information Systems Management Bina Nusantara University Jakarta11480 Indonesia School of Information Systems Department BINUS Undergraduate Program Bina Nusantara University Jakarta11480 Indonesia Informatics Engineering Engineering Bhayangkara University Jakarta Raya Indonesia Computer Science Study Program Faculty of Mathematics and Natural Sciences Pakuan University Bogor Indonesia

An e-Commerce company has been using an Enterprise Resource Planning (ERP) system for several years, but is still constrained in its implementation, this is reflected in the number of issue/change request tickets submitted by users who have not been able to reach ideal conditions. To overcome this problem, we need an appropriate reference model, the ERP system user acceptance model in companies. The study conducted factors that influence the level of acceptance of SAP ERP users in the XYZ group to then determine a model that is able to explain practically the level of ERP system user acceptance, which in turn can produce concrete proposals to increase ERP system user acceptance. Research is quantitative descriptive using factor analysis and regression analysis methods. The research method uses a questionnaire with a total of 107 valid respondents coming from 8 company names under the XYZ group in 6 Southeast Asian countries. The conclusion of the study is that there are 24 indicators and 4 factors that influence user acceptance of the SAP ERP system. These four factors are the low contribution of the ERP system, the quality of ERP systems and data, the development of ERP systems, and also the low quality of ERP system supporters. It is hoped that by optimizing the value of the 4 factors, the XYZ group can increase user acceptance of the SAP ERP system so that the system can provide benefits expected by the company to be competitive advantage. © 2021 Published under licence by IOP Publishing Ltd.

关键词： Factor analysis

来源：评论

学校读者我要写书评

暂无评论

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

请选择保存的检索档案：

请选择收藏分类：

通借通还

建议与咨询 留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

请选择保存的检索档案： 新增检索档案 确定 取消

请选择收藏分类： 新增自定义分类 确定 取消

通借通还

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

请选择保存的检索档案：

请选择收藏分类：