检索结果-内蒙古大学图书馆

Strengthening and toughening mechanisms of martensite-bainite microstructure in 2 GPa ultra-high strength steel during hot stamping

引用

Science China Technological Sciences 2025年第5期68卷 19-33页

作者： Yanli SONG Ye LI Jue LU Lin HUA Yanfeng GU Yikuan YANG Hubei Key Laboratory of Advanced Technology for Automotive Components Wuhan University of Technology State Key Laboratory of Advanced Technology for Materials Synthesis and Processing Wuhan University of Technology

In response to the growing demand for energy efficiency, safety, and lightweight designs in new energy vehicles, this study addresses the challenge of balancing strength and toughness in ultra-high strength steel(UHSS) components produced by hot stamping. An innovative hot stamping process based on a martensite-bainite(M-B) complex-phase microstructure was proposed to enhance the strength and toughness of UHSS. The microstructural evolution of the M-B complexphase during the hot stamping process was investigated using commercial B1800HS steel. With a microstructure consisting of 87.4.% martensite, 8.7% lower bainite, and 3.9% film-like retained austenite by volume fraction, the steel achieved a tensile strength of 1944 MPa, total elongation of 9.66%, and impact energy of 25.8 J. Compared with conventional hot stamping, the strength of the material showed only a slight improvement, whereas elongation and impact energy were enhanced by approximately 53% and 32%, respectively. A quantitative relationship among process parameters, resulting microstructure, and mechanical properties was established. Optimization between strength and toughness was observed when the low bainite volume fraction ranged from 5.06% to 8.73%. The toughening mechanisms are attributed to the refinement of martensite lath bundles(width of 202 nm) facilitated by bainite formation, the increase in high-angle grain boundaries, and the presence of nanoscale retained austenite(width of 80 nm) between the laths. Additionally, the refinement of grains and the formation of nanoscale(Nb, Ti)C precipitates(diameter of 17 nm) further contributed to the overall strength. The developed M-B complexphase process, which involves medium-temperature slow cooling followed by rapid low-temperature quenching, provides an optimal combination of strength and toughness for a wide range of applications.

关键词： ultra-high strength steel hot stamping strengthening and toughening mechanisms martensite-bainite complex-phase microstructure

来源：评论

学校读者我要写书评

暂无评论

Degradation mechanism,direct regeneration and upcycling of ternary cathode material for retired lithium-ion power batteries

引用

Journal of Energy Chemistry 2025年第3期102卷 534-554页

作者： Juan Wang Dongqi Li Weihao Zeng Xingye Chen Yixin Zhang Shaojie Zhang Zhongpeng Li Changhao Li Shichun Mu State Key Laboratory of Advanced Technology for Materials Synthesis and Processing Wuhan University of TechnologyWuhan 430070HubeiChina

With the approaching of large-scale retirement of power lithium-ion batteries(LIBs),their urgent handling is required for environmental protection and resource ***,at present,substantial spent power batteries,especially for those high recovery value cathode materials,have not been greenly,sustainably,and efficiently *** to the traditional recovery method for cathode materials with high energy consumption and severe secondary pollution,the direct repair regeneration,as a new type of short-process and efficient treatment methods,has attracted widespread ***,it still faces challenges in homogenization repair,electrochemical performance decline,and scaling-up *** promote the direct regeneration technology development of failed NCM materials,herein we deeply discuss the failure mechanism of nickel-cobalt-manganese(NCM)ternary cathode materials,including element loss,Li/Ni mixing,phase transformation,structural defects,oxygen release,and surface degradation and *** on this,the detailed analysis and summary of the direct regeneration method embracing solid-phase sintering,eutectic salt assistance,solvothermal synthesis,sol-gel process,spray drying,and redox mediation are ***,the upcycling strategy for regeneration materials,such as single-crystallization and high-nickelization,structural regulation,ion doping,and surface engineering,are discussed in ***,the challenges faced by the direct regeneration and corresponding countermeasures are pointed ***,this review provides valuable guidance for the efficient and high-value recovery of failed cathode materials.

关键词： Spent NCM materials Retired lithium-ion power battery Degradation mechanism Direct regeneration Upcycling strategy

来源：评论

学校读者我要写书评

暂无评论

Effect of Ti Additions on Mechanical and Thermodynamic Properties of W-Ti Alloys: A First-principles Study

引用

Journal of Wuhan University of technology(materials Science) 2025年第1期40卷 246-257页

作者： ZHANG Jian NIE Wei HUANG Jin ZHU Ke LIU Ruxia ZHANG Ruizhi LUO Guoqiang SHEN Qiang State Key Laboratory of Advanced Technology for Materials Synthesis and Processing Wuhan University of TechnologyWuhan 430070China Institute for Carbon Neutrality University of Science and Technology BeijingBeijing 100083China

The mechanical and thermodynamic properties of W-Ti alloys(including W_(15)Ti_(1),W_(14)Ti_(2),W_(12)Ti_(4) and W_(8)Ti_(8) alloys)were investigated by the first-principles approach based on density functional *** results indicate that W-Ti alloys except W_(8)Ti_(8) are thermodynamically *** modulus and hardness of W-Ti alloys are smaller than those of pure tungsten and gradually decrease with increasing Ti ***,their B/G ratios and Poisson's ratios exceed those of pure tungsten,suggesting that the introduction of Ti decreases the mechanical strength while enhancing the ductility of W-Ti *** thermal expansion coefficients for W-Ti alloys all surpass those of pure tungsten,indicating that the introduction of titanium exacerbates the thermal expansion behavior of W-Ti ***,elevated pressure has the capacity to suppress the thermal expansion tendencies in titanium-doped tungsten *** study offers theoretical insights for the design of nuclear materials by exploring the mechanical and thermodynamic properties of W-Ti alloys.

关键词： first-principles mechanical properties thermodynamic properties tungsten-titanium alloys

来源：评论

学校读者我要写书评

暂无评论

Ionic liquids-assisted in-situ targeted defect-healing strategy for high-performance sprayed perovskite modules

引用

Journal of Energy Chemistry 2025年第5期104卷 756-764页

作者： Jize Wang Xinxin Yu Cong Geng Wangnan Li Ying Liang Bin Li Yong Peng Yi-Bing Cheng State Key Laboratory of Advanced Technology for Materials Synthesis and Processing Wuhan University of Technology Hubei Key Laboratory of Low Dimensional Optoelectronic Materials and Devices Hubei University of Arts and Science Hubei Longzhong Laboratory Wuhan University of Technology (Xiangyang Demonstration Zone)

In the process of spraying coating perovskite films,the "coffee ring" effect （CRE） leads to the problem of excessive organic ammonium salt accumulation in local areas that cannot be completely *** introduce an in-situ targeted defect-healing strategy by incorporating butylamine formate （BAFa） ionic liquid into the spray *** liquids,due to their long carbon chain structure,tend to target flow towards the CRE region during the droplet evaporation *** coordination between the lone pair electrons in the C=O group of BAFa and Pb2+effectively reduces defects in perovskite and suppresses non-radiative recombination ***,amine ligands,which are repelled to the film surface and grain boundaries,form a thin insulating monolayer in the CRE areas,forcing charge carriers to transport through areas of the perovskite with fewer *** approach enables the crystallization control and defect-heal over the Cs0.19FA0.81PbI3-x-yBrxClyperovskite ***,the champion perovskite solar cell achieved a power conversion efficiency of 22.04%,while mini-modules with an effective area of 64.8 cm2reached a peak power conversion efficiency of 18.35%,demonstrating the significant potential for commercializing large-area perovskite solar cells.

关键词： Ion liquid Perovskite solar cell Spray-coating Targeted defect-healing “Coffee-ring” effect

来源：评论

学校读者我要写书评

暂无评论

Designing carboxymethyl cellulose based hydrogel electrolyte membranes enhanced by inorganic nanoparticle toward stable zinc anode

引用

Green Energy & Environment 2025年第3期10卷 537-550页

作者： Xiangye Li Yuan Li Yu Jiang Dahui Wang Fen Ran State Key Laboratory of Advanced Processing and Recycling of Non-ferrous Metals Department of Polymeric Materials EngineeringSchool of Material Science and EngineeringLanzhou University of TechnologyLanzhou730050China

Aqueous zinc metal batteries have garnered substantial attention ascribing to affordability,intrinsic safety,and environmental benignity Nevertheless,zinc metal batteries yet are challenged with potential service life issues resulted from dendrites and side *** this paper,a strategy of nanoparticles doped hydrogel is proposed for constructing carboxymethyl cellulose/graphite oxide hybrid hydrogel electrolyte membranes with exceptional ionic conductivity,anti-swelling property,and simultaneously addressing the dendrites and parasitic *** pivotal functions of the carboxymethyl cellulose/graphite oxide hydrogel electrolyte in mitigating hydrogen evolution and fostering accelerated Zn deposition have been elucidated based on principles of thermodynamic and reaction *** carboxymethyl cellulose/graphite oxide hydrogel electrolyte endows exceptional cycling longevity (800 h at 1 mA cm^(-2)/1 mAh cm^(-2)) for Znjj Zn battery,as well as high Coulombic efficiency for Znjj Cu battery (averagely 99.14%within 439 cycles at 1 mA cm^(-2)/1 mAh cm^(-2)).The assembled Znjj NH_(4)V_(4)O_(10)battery delivers a high reversible specific capacity of 328.5 mAh g^(-1)at 0.1 A g^(-1).Moreover,the device of Znjj NH_(4)V_(4)O_(10)pouch battery remains operational under severe conditions like bending and *** work provides valuable reference in developing inorganic nanoparticle hybrid hydrogel electrolyte for realizing high-performance zinc metal batteries.

关键词： Carboxymethyl cellulose Graphite oxide Hydrogel electrolyte Anti-swelling

来源：评论

学校读者我要写书评

暂无评论

The effect of room temperature magnetic field on photoluminescence of Mn:CsPbBr_(3) quantum dots prepared by one-pot method in air

引用

Nano Research 2025年第4期18卷 561-568页

作者： Mengwei Chen Chenguang Shen Wei Huang Yingping Yang Jie Shen Department of Physics School of Physics and MechanicsWuhan University of TechnologyWuhan 430070China State Key Laboratory of Advanced Technology for Materials Synthesis and Processing School of Materials Science and EngineeringWuhan University of TechnologyWuhan 430070China

The generation and manipulation of spin-polarized electrons at room temperature are essential for the development of advanced spin-optoelectronic *** this work,a one-pot method was used to successfully synthesize homogenous Mn:CsPbBr_(3) perovskite quantum dots in air with particle sizes of 7−8 *** effects of Mn doping on the structure,optical and magnetic properties of CsPbBr_(3) quantum dots were *** findings demonstrated proper Mn doping improved the crystallinity and photoluminescence(PL)of quantum *** prepared quantum dots have a narrow full width at half maximum emission(FWHM)of about 17−20 *** magnetic properties of the doped samples and the effect of the magnetic field on the PL spectra properties were *** results show that trace Mn doping can improve the room-temperature ferromagnetism of CsPbBr_(3) quantum *** with magnetic elements makes CsPbBr_(3) quantum dots more responsive to the applied magnetic *** at a lower 50 mT magnetic field,the PL peak of Mn:CsPbBr_(3) still declined 5.91%.Mn:CsPbBr_(3) quantum dots are a new type of multifunctional material that is beneficial to spintronics *** work demonstrates a low-cost synthesis *** should make all-inorganic perovskite quantum dots a promising material for room-temperature spin optoelectronic devices.

关键词： CsPbBr_(3)quantum dots Mn doping one-pot method ferromagnetism magnetic field

来源：评论

学校读者我要写书评

暂无评论

Ultrafast Laser Irradiation Induced Oxidation of Dopant-Free Spiro-OMeTAD for Improving the Perovskite Solar Cells Performance

引用

Energy & Environmental materials 2025年第2期8卷 288-294页

作者： Jiaqi Meng Xiangyu Chen Weihan Li Nianyao Chai Zhongle Zeng Yunfan Yue Fengyi Zhao Xuewen Wang Center of Femtosecond Laser Manufacturing for Advanced Materials and Devices State Key Laboratory of Advanced Technology for Materials Synthesis and Processing Wuhan University of Technology School of Materials Science and Engineering Wuhan University of Technology International School of Materials Science and Engineering Wuhan University of Technology National Energy Key Laboratory for New Hydrogen-Ammonia Energy Technologies Foshan Xianhu Laboratory

The exceptional photoelectric performance and high compatibility of perovskite materials render perovskite solar cells highly promising for extensive development,thus garnering significant *** perovskite solar cells,the hole transport layer plays a crucial *** the commonly employed organic small molecule hole transport material Spiro-OMeTAD,a certain period of oxidation treatment is required to achieve complete transport ***,this posttreatment oxidation processes typically rely on ambient oxidation,which poses challenges in terms of precise control and leads to degradation of the perovskite light absorption *** approach fails to meet the demands for high efficiency and stability in practical ***,the mechanism of ultrafast laser on Spiro-OMeTAD and the reaction process for laser-induced oxidation of it are ***2at Perovskite/Spiro-OMeTAD interface breaks down to produce I2upon ultrafast laser irradiation and I2promote the oxidation *** the laser irradiation oxidation processing,a higher stability of perovskite solar cells is *** work establishes a new approach toward oxidation treatment of Spiro-OMeTAD.

关键词： hole transport layer perovskite solar cells ultrafast laser irradiation undoped Spiro-OMeTAD

来源：评论

学校读者我要写书评

暂无评论

Homologous CoS2 interface with directed electron transfer and strong chloridion repulsion for efficient seawater oxidation

引用

Science China Chemistry 2025年第5期68卷 1869-1878页

作者： Yuan Tian Jiang-Bo Chen Jie Ying Ge Tian Yu-Xuan Xiao Yi Lu Si-Ming Wu Wei Geng Ling Shen Xiao-Yu Yang State Key Laboratory of Advanced Technology for Materials Synthesis and Processing and School of Materials Science and Engineeringand Shenzhen Research Institute & Laoshan LaboratoryWuhan University of Technology School of Chemical Engineering and Technology Sun Yat-sen University National Energy Key Laboratory for New Hydrogen-Ammonia Energy Technologies Foshan Xianhu Laboratory

Seawater electrolysis is a highly promising method to produce high energy density hydrogen,especially in dry areas that have scarce freshwater ***,application of seawater electrolysis is confronted by two major problems associated with catalysts employed for the anodic oxygen evolution reaction（OER） including the competitive hypochlorite evolution reaction（HCER） and strong chloridion（Cl-） triggered *** studies aimed at overcoming these problems,a facile method has been developed to synthesize a homologous CoS2heterojunction as an OER *** to a difference in work functions at the interface and increased electron density,this material has directed electron transfer and strong chloridion repulsion properties,*** have shown that CoS2achieves low overpotentials of 289 and 322 mV at 10 mA cm-2current density in respective alkaline（1 M KOH） and alkaline simulated seawater ***,the outstanding stability of CoS2is reflected in a negligible decline in activity during promotion of the OER for 100 *** of density functional theory calculations reveal that the homologous CoS2heterojunction promotes directed electron transport for optimizing adsorption/desorption of reactive species and heightens the Cl-adsorption energy for strongly repulsing Cl-,phenomena that enhance OER performance in alkaline simulated seawater.

关键词： metal sulfide homologous heterojunction directed transfer chloride ion repulsion seawater electrolysis

来源：评论

学校读者我要写书评

暂无评论

A numerical method for predicting bursting strength of composite rocket motor case considering filament winding process-induced stress

引用

Chinese Journal of Aeronautics 2025年第2期38卷 505-518页

作者： Jiqiu LIANG Fei ZHAO Dan WU Anxin DING Hubei Key Laboratory of Advanced Aerospace Propulsion Technology Wuhan 430040China System Design Institute of Hubei Aerospace Technology Academy Wuhan 430040China School of Materials Science and Engineering Wuhan University of TechnologyWuhan 430070China State Key Laboratory of Advanced Technology for Materials Synthesis and Processing Wuhan University of TechnologyWuhan 430070China

A numerical method to predict the bursting strength of filament wound composite rocket motor case is proposed *** method can evaluate the longitudinal stress evolution of each composite layer as impregnated filaments with fiber tension are wound layer by layer,and consider the effects of accumulated stress and deformation during filament winding on the bursting strength of composite ***∅520 mm composite cases as a case study,the filament-winding-process-induced stress and deformation as well as progressive damage behavior are numerically predicted,followed by a comparison with experimental *** numerical results show that the predicted bursting pressures for composite cases manufactured on the mandrels with and without a flexible component are 14.20 MPa and 21.40 MPa,*** values exhibit slight deviation from the measured pressures of 13.50 MPa and 21.57 ***,the predicted damage locations,situated respectively in the dome and cylinder,agree well with the experimental *** observations indicate that use of flexible component reduces the load-bearing capacity of the ***,it validates the reliability and accuracy of the proposed numerical method in predicting the bursting strength of composite cases.

关键词： Composite case Fiber tension Bursting strengt hProgressive damage analysis Filament winding

来源：评论

学校读者我要写书评

暂无评论

Design and characterization of 3D printed gradient scaffolds with spatial distribution of pore sizes

引用

Ceramics International 2025年第9期51卷 12185-12196页

作者： Ye, Fan Yang, He Hong, Chuhang Wu, Xiaopei Dai, Honglian State Key Laboratory of Advanced Technology for Materials Synthesis and Processing Wuhan University of Technology Wuhan430070 China National Energy Key Laboratory for New Hydrogen-ammonia Energy Technologies Foshan Xianhu Laboratory Foshan528200 China

In bone repair, scaffold structural design is essential for optimizing mechanical performance and osteogenic potential. Gradient structural scaffolds are engineered to balance mechanical qualities and permeability which can improve the material transport capacity of scaffolds. This study designed and fabricated gradient structural scaffolds with spatially distributed pore sizes, and investigated their mechanical and fluid dynamics properties, coupled with in vitro osteogenic experiments to understand the impact of pore sizes distribution. The results indicated that, compared to traditional uniform pore scaffolds, gradient scaffolds exhibited a significant increase in mechanical strength, fluid permeability, and in vitro osteogenic activity. To sum up, the gradient scaffolds demonstrated better comprehensive performance and potential for use in the structural design of bone repair scaffolds, offering an important reference value for the three-dimensional structural design of scaffolds. © 2025 Elsevier Ltd and Techna Group S.r.l.

关键词： Bone

来源：评论

学校读者我要写书评

暂无评论

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

请选择保存的检索档案：

请选择收藏分类：

通借通还

建议与咨询 留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

请选择保存的检索档案： 新增检索档案 确定 取消

请选择收藏分类： 新增自定义分类 确定 取消

通借通还

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

请选择保存的检索档案：

请选择收藏分类：