检索结果-内蒙古大学图书馆

第八届国际振动工程会议

作者： Ruiqin Wu Wei Zhu Tianjin Key Laboratory of the Design and Intelligent Control of the Advanced Mechatronical System School of Mechanical EngineeringTianjin University of Technology

The amplitude-frequency characteristics of a non-planar complex structure composed of a flexible beam and a ring are systematically investigated. The kinetic and strain potential energy expressions are theoretically calculated for the beam-ring system. Hamilton's principle is employed to derive the nonlinear governing equations of motion of the beam-ring structure. The nonlinear partial governing differential equation of motion for the beam-ring system is discretized into two coupled ordinary differential equations including quadratic and cubic nonlinearities by using Galerkin's technique. The method of multiple scales is utilized to approximately analyze the dynamical system and yield a set of autonomous equations. The amplitude-frequency characteristics and the stability of the steady-state solution are studied numerically. The frequency-response curves show that there exist multi-value solution and jump phenomenon in the system and some parameters of the amplitude-frequency equations have significant contributions to the nonlinear responses of the beam-ring system.

关键词： the beam-ring structure amplitude-frequency characteristics steady-state solution jump phenomenon

来源：评论

学校读者我要写书评

暂无评论

Pickup Manipulator design and Its Kinematics Simulation 2

Pickup Manipulator Design and Its Kinematics Simulation

引用

2018 2nd International Symposium on Resource Exploration and Environmental Science, REES 2018

作者： Zhang, Zhongdang Zhang, Zhaoqiang Ma, Shitai Zhou, Haibo Tianjin University of Technology Tianjin Key Laboratory for Advanced Mechatronic System Design and Intelligent Control Tianjin300384 China National Demonstration Center for Experimental Mechanical and Electrical Engineering Education Tianjin300384 China

In order to improve the flexibility of the pickup manipulator and solve the problem of picking up small sports balls in training ground such as golfing, tennis, and table tennis, a 5-DOF pickup manipulator structure is designed. According to the pickup task requirements of the manipulator, through theoretical calculations, the 86HS series stepping motor is selected as the driving motors of the front end joints. Based on this, the stepping motor control system is designed to realize the closed-loop control of the manipulator. Then the manipulator model is built using D-H method, the inverse kinematics solution is calculated, and the analysis of kinematic theory is conducted. Finally, the targeted pickup point is selected to carry out case simulation analysis of the manipulator, the motion law of the manipulator is verified to be reasonable and the task of picking up small sports balls is completed. © Published under licence by IOP Publishing Ltd.

关键词： Manipulators

来源：评论

学校读者我要写书评

暂无评论

Nonlinear Deep Subspace Network for Micro-expression Recognition 3

Nonlinear Deep Subspace Network for Micro-expression Recogni...

引用

3rd Workshop on Facial Micro-Expression: advanced Techniques for Multi-Modal Facial Expression Analysis, FME 2023

作者： Feng, Weijia Xu, Manlu Chen, Yuanxu Wang, Xiaofeng Guo, Jia Dai, Lei Wang, Nan Zuo, Xinyu Li, Xiaoxue College of Computer and Information Engineering Tianjin Normal University Tianjin China Ping An Technology Shenzhen China Tianjin Key Laboratory for Advanced Mechatronic System Design and Intelligent Control Tianjin University of Technology Tianjin China

ISBN: (纸本)9798400702853

Deep learning (DL) models have been widely studied in the field of micro-expression recognition (MER). However, micro-expressions (MEs) suffer from small number of samples and difficulty in extracting subtle and transient features, resulting in limited improvement in the recognition performance. In addition, DL models are prone to overfitting problems and are difficult to extract discriminative features of facial actions from ME images or sequences. To address these issues, we propose a MER method that combines a nonlinear deep subspace network and optical flow features. Firstly, facial motion features are captured using optical flow computation, and then the optical flow features are input into a kernel principal component analysis network (KPCANet) to further learn deeper spatio-temporal features. Finally, a linear support vector machine (SVM) is used for ME classification. Experiments conducted on four public spontaneous ME datasets including SMIC, CASME, CASME II and SAMM validate the effectiveness of the proposed method. The experimental results demonstrate that the proposed method achieves even better recognition performance compared to existing state-of-the-art MER methods. © 2023 ACM.

关键词： Principal component analysis

来源：评论

学校读者我要写书评

暂无评论

A copula-based reliability model for phased mission systems with dependent components (vol 39, pg 1533, 2023)

引用

QUALITY AND RELIABILITY ENGINEERING INTERNATIONAL 2023年第7期39卷 3179-3179页

作者： Li, X. Zhan, K. Xiong, X. Vu, T. Q. Key Laboratory of Advanced Transducers and Intelligent Control System Ministry of Education Taiyuan University of Technology Taiyuan China School of Media Design College of Technology and Design University of Economics Ho Chi Minh City Vietnam

Recently, researches on the reliability analysis of phased mission systems (PMSs) are very popular. And most of the existing research on PMSs assumed that all the components are statistically independent on each other, which is not meet the engineering reality. The system structure changes from phase to phase in the PMSs, so the dependency among components may also change in different phases. Meanwhile, the well-known phase dependency is also existing in the system reliability modeling. To model the varying dependency among components and phase dependency at the same time, a copula-based method is proposed for the reliability analysis of PMS with correlated components. Firstly, the system reliability of multi-state PMS with dependent components is evaluated by different copula functions. Then, multiple indicators are used to select the optimal copula functions for different phases. And an engineering case is illustrated to show the proposed copula-based method.

关键词： copula dependent components modular method phased mission system

来源：评论

学校读者我要写书评

暂无评论

Mechanism design and Motion Simulation of Mobile Robot with Compound Motion Mode

Mechanism Design and Motion Simulation of Mobile Robot with ...

引用

2021 IEEE International Conference on Electrical Engineering and Mechatronics Technology, ICEEMT 2021

作者： Shi, Yanan Yang, Yuwei Liu, Zhenzhong Zhang, Haiming Tianjin University of Technology National Demonstration Center For Experimental Mechanical and Electrical Engineering Education Tianjin Key Laboratory For Advanced Mechatronic System Design and Intelligent Control School of Mechanical Engineering Tianjin China

ISBN: (纸本)9781665441285

Aiming at the problem of poor trafficability and difficulty in dealing with complex environment of traditional mobile robot, we proposed a climbing and hopping hybrid mobile robot. In this paper, we took the spring four-bar linkage mechanism as the hopping mechanism and the C-shaped wheel foot mechanism as the walking mechanism. Completed the structure design of the robot. Realized the assembly and disassembly of the virtual prototype, and completed the motion simulation and analysis. The results show that the robot is stable in the aspects of structure design and its jumping height can reach 988mm, and has a great potential in reconnaissance, monitoring, survey etc. © 2021 IEEE.

关键词： Mobile robots

来源：评论

学校读者我要写书评

暂无评论

Simulation Study on the Influence of Drilling Parameters on the Temperature of Skull Drilling

Simulation Study on the Influence of Drilling Parameters on ...

引用

2021 IEEE International Conference on Electrical Engineering and Mechatronics Technology, ICEEMT 2021

作者： Jiang, Wenyu Liu, Zhenzhong Tianjin University of Technology National Demonstration Center For Experimental Mechanical and Electrical Engineering Education School of Mechanical Engineering Tianjin Key Laboratory For Advanced Mechatronic System Design and Intelligent Control Tianjin China

ISBN: (纸本)9781665441285

Skull drilling is an important and difficult process in neurosurgical craniotomy, which will inevitably produce a lot of heat. Correct understanding of the heat production law of skull drilling has important guiding significance for craniotomy robot. In this study, cortical bone and cancellous bone were layered to establish models according to the 3D reconstruction data of skull. The finite element method based on ABAQUS is used to establish the skull drilling model and realize the simulation of bone tissue surgical instrument interaction state for surgical robot. The results show that when the drill rotation speed and feed speed increase, the drilling temperature will also increase, but the drill rotation speed will have a more significant effect on bone drilling temperature, and when the drill rotation speed is low (300r/min, 600r/min), the drill bit diameter has little effect on the drilling temperature, but when the drill rotation speed is higher (900r/min, 1200r/min), the larger diameter drill bit(11mm) will produce more drilling heat. © 2021 IEEE.

关键词： Finite element method

来源：评论

学校读者我要写书评

暂无评论

design of wearable squat booster for automobile assembler based on ergonomics 6

Design of wearable squat booster for automobile assembler ba...

引用

2020 6th International Forum on Engineering Materials and Manufacturing Technology, IFEMMT 2020

作者： Chen, Zhewen Qiao, Zhifeng Bao, Tianxu Dou, Fuchao Chen, Xinpu Tianjin University of Technology Tianjin Key Laboratory for Advanced Mechatronic System Design and Intelligent Control School of Mechanical Engineering National Demonstration Center for Experimental Mechanical and Electrical Engineering Education Tianjin China

Aiming at the problem that automobile assembler need to squat for a long time, a wearable squatting assistance system with low cost, simple control and easy to squat and walk is designed. Based on ergonomics and finite element theory, UG was used to draw a three-dimensional solid model of the wearable squatting power system for automobile assemblers. With the help of ANSYS software, the statics analysis of key components is carried out to check their strength and stiffness. It is concluded that the wearable squatting power assist device for automotive fitters based on ergonomics has reached the design requirements in terms of function use and strength and stiffness. © Published under licence by IOP Publishing Ltd.

关键词： Ergonomics

来源：评论

学校读者我要写书评

暂无评论

Optimization of Robot Hopping Mechanism Based on Parametric Model Method

Optimization of Robot Hopping Mechanism Based on Parametric ...

引用

2021 IEEE International Conference on Electrical Engineering and Mechatronics Technology, ICEEMT 2021

作者： Shi, Yanan Yang, Yuwei Liu, Zhenzhong Zhang, Haiming Tianjin University of Technology National Demonstration Center For Experimental Mechanical and Electrical Engineering Education School of Mechanical Engineering Tianjin Key Laboratory For Advanced Mechatronic System Design and Intelligent Control Tianjin China

ISBN: (纸本)9781665441285

In order to solve the problem of hopping mechanism design of robot, we proposed a method of optimization of transmission mechanism based on parametric model. In this paper, the optimization of energy transfer efficiency of robot jump mechanism is completed by parametric model method through the mechanism simplification, parametric modeling and parameter optimization. The results show that the method can greatly optimize the energy transfer efficiency and reduce the driving torque required by 74.6%. It provides a feasible optimization method for the design of the robot hopping structure. © 2021 IEEE.

关键词： Energy transfer

来源：评论

学校读者我要写书评

暂无评论

Dynamic Modeling and Simulation of Flexible Load system Operated by Reconfigurable Manipulators Under Different Constraints

Dynamic Modeling and Simulation of Flexible Load System Oper...

引用

IEEE International Conference on Mechatronics and Automation

作者： Huidong Ma Jinjin Guo Weimin Ge Xiaofeng Wang School of Mechanical Engineering Tianjin University of Technology Tianjin Key Laboratory of the Design and Intelligent Control of the Advanced Mechatronical System Tianjin China

This paper aims at solving the problems that the manipulator will be constrained by the flexible load, and the caused constraint force is difficult to control. Based on the deflection screw theory, the dynamic model of the manipulator system is established by using the Lagrange equation. Firstly, according to the interaction of the end effector, the flexible load and the environmental constraints of the manipulator, the equation of motion of the entire system is built. Secondly, the dynamic model of the manipulator system is set up, that the system including the flexible load and the manipulator. Finally, Under the certain known environmental constraints, the dynamic modeling of a manipulator is performed. The effectiveness of the proposed method is verified by the simulation of a flexible beam operated by a 3-DOF manipulator.

关键词： Manipulator dynamics Force Mathematical model Load modeling Dynamics Torque

来源：评论

学校读者我要写书评

暂无评论

Tooth Surface design for Variable Transmission Ratio Bevel Gearing

引用

Applied Mathematics 2015年第10期6卷 1685-1695页

作者： Nan Yang Dawei Zhang Yanling Tian School of Mechanical Engineering Tianjin University Tianjin China Tianjin Key Laboratory of the Design and Intelligent Control of the Advanced Mechatronical System School of Mechanical Engineering Tianjin University of Technology Tianjin China

A novel CAD method for tooth profile based on the gearing feature has been proposed in this paper, and this method could be applied to the variable transmission ratio and three-dimension situation. The two pitch curves of the two gears can be generated due to the given transmission ratio. The tooth profile curves are formed in each coordinate system of its pitch curve by the gearing process. Finally, the tooth profile could be extracted and translated into a real dimension by CAD method. It is provided a simply thought for tooth profile design to avoid so much complicated mathematical reasoning.

关键词： Computer-Aided design Computational Geometry Gear design Gear Geometry

来源：评论

学校读者我要写书评

暂无评论

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

请选择保存的检索档案：

请选择收藏分类：

通借通还

建议与咨询 留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

请选择保存的检索档案： 新增检索档案 确定 取消

请选择收藏分类： 新增自定义分类 确定 取消

通借通还

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

请选择保存的检索档案：

请选择收藏分类：